The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| Replacement of engine assembly | ·
Injector compensation code registration ·
Pilot quantity learning |
Engine starting |
|
| Clear Crank Time Compensation Data | Engine starting |
|
|
| Replacement of injector assembly | ·
Injector compensation code registration ·
Pilot quantity learning |
Engine starting |
|
·
Replacement of diesel throttle body assembly ·
Replacement of electric EGR control valve assembly ·
Replacement of turbocharger sub-assembly ·
Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor |
Perform initialization | - |
|
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
Make sure foreign matter does not enter the fuel path.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
1.REMOVE ENGINE ASSEMBLY
44763C
2.REMOVE NO. 2 HOSE TO HOSE TUBE
12632
3.REMOVE NO. 2 ENGINE COVER BRACKET
82121
4.REMOVE ENGINE WIRE
17363K
5.REMOVE INTERCOOLER AIR TUBE
26100G
6.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
25733A
10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
11.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
12.REMOVE PIPE CLAMP (w/ DPF)
12631A
13.REMOVE ENGINE COVER BRACKET
23265C
14.REMOVE GAS FILTER
89421C
15.REMOVE DIESEL TURBO PRESSURE SENSOR
25625
16.REMOVE EGR VALVE BRACKET
25612
17.REMOVE NO. 2 EGR PIPE
16206B
18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25601
19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
25804
20.REMOVE VACUUM CONTROL VALVE SET
16209
21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
25800
22.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
11409
23.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
24.REMOVE NO. 2 FUEL PIPE
25.REMOVE WIRING HARNESS CLAMP BRACKET
17118
26.REMOVE MANIFOLD STAY
22803
27.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
28.REMOVE FUEL PUMP MOTOR WIRE
23273H
29.REMOVE NO. 2 FUEL HOSE
23271H
30.REMOVE NO. 1 FUEL HOSE
23804D
31.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)
23815D
32.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804C
33.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
34.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
35.REMOVE INTAKE MANIFOLD
36.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
37.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
38.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
39.REMOVE WIRING HARNESS CLAMP BRACKET
23701
40.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
44781
41.REMOVE HOSE BRACKET
88431
42.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
16282
43.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
16281
44.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
23295D
45.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
89467B
46.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)
17167
47.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17271
48.REMOVE NO. 1 TURBO INSULATOR
49.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
50.REMOVE EXHAUST PIPE SUPPORT STAY
25051
51.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
12261
52.REMOVE PCV HOSE
16279
53.REMOVE NO. 3 WATER BY-PASS PIPE
16268
54.REMOVE NO. 1 WATER BY-PASS PIPE
16284
55.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
17293
56.REMOVE TURBOCHARGER STAY
15474
57.REMOVE TURBO OIL OUTLET PIPE
15407
58.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
59.REMOVE TURBOCHARGER SUB-ASSEMBLY
16207
60.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
16304
61.REMOVE WATER OUTLET SUB-ASSEMBLY
16321
62.REMOVE WATER INLET
16331A
63.REMOVE THERMOSTAT
16603
64.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.
16620
65.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.
13496
66.REMOVE CRANKSHAFT PULLY COVER
13471
67.REMOVE CRANKSHAFT PULLEY
16575C
68.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
12281A
69.REMOVE NO. 1 ENGINE HANGER
12501
70.REMOVE GENERATOR BRACKET SUB-ASSEMBLY
23670
71.REMOVE INJECTOR ASSEMBLY
23682
72.REMOVE NOZZLE HOLDER GASKET
11401G
73.REMOVE CAMSHAFT POSITION SENSOR
11201
74.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Nozzle Holder Clamp Seat |
Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
| *1 | Cylinder Head Cover Gasket |
| *2 | No. 2 Cylinder Head Cover Gasket |
| *3 | Camshaft Bearing Cap Oil Hole Gasket |
Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.
12144
75.REMOVE OIL PAN COVER SILENCER
Remove the 5 bolts and oil pan cover silencer from the oil pan sub-assembly.
89491
76.REMOVE ENGINE OIL LEVEL SENSOR
12101
77.REMOVE OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 23 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.
Be careful not to damage the cylinder block sub-assembly flange.
16100
78.REMOVE ENGINE WATER PUMP ASSEMBLY
79.SET NO. 1 CYLINDER TO TDC/COMPRESSION
11324
80.REMOVE TIMING CHAIN COVER PLATE
22100
81.REMOVE SUPPLY PUMP ASSEMBLY
22815A
82.REMOVE INJECTION PUMP INSULATOR
11302
83.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 20 bolts from the timing chain cover sub-assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.
Remove the timing chain case gasket from the timing chain case assembly.
11303A
84.REMOVE FRONT CRANKSHAFT OIL SEAL
| *a | Protective Tape |
| *b | Wooden Block |
Using a screwdriver and wooden block, pull out the front crankshaft oil seal.
Do not damage the surface of the front crankshaft oil seal press fit hole.
85.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR
Using a dial indicator, measure the backlash.
0.02 to 0.3 mm (0.000787 to 0.0118 in.)
0.42 mm (0.0165 in.)
If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.
13519
86.REMOVE OIL PUMP DRIVE GEAR
Remove the oil pump drive gear from the crankshaft.
13566B
87.REMOVE TIMING CHAIN GUIDE
13550
88.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
89.REMOVE NO. 2 CHAIN TENSIONER SLIPPER
13562
90.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13507
91.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
13540
92.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
93.REMOVE NO. 1 CHAIN TENSIONER SLIPPER
13561
94.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
95.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY
13523
96.REMOVE CAMSHAFT TIMING SPROCKET
11310
97.REMOVE TIMING CHAIN CASE ASSEMBLY
Remove the 15 bolts from the timing chain case assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.
Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.