Home › Engine / Hybrid System › 1GD-FTV ENGINE MECHANICAL › ENGINE UNIT › 2015.11–2016.10
RM33J0E _51 Engine / Hybrid System _038421 1GD-FTV ENGINE MECHANICAL _0196026 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 44763C 1.REMOVE NO. 2 HOSE TO HOSE TUBE

a.
A343494

Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.


b.

Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.


Hide 12632 2.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 3.REMOVE ENGINE WIRE

Hide 26100G 5.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 8.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 12631A 12.REMOVE ENGINE COVER BRACKET

a.
A343495

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 89421C 14.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 15.REMOVE EGR VALVE BRACKET

Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.

except i-ART:

i.
A343587

Disconnect the connector from the common rail assembly.


ii.

Detach the 2 clamps and remove the connecting wire from the hose bracket.



b.
A343497

Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


c.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


d.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 19.REMOVE VACUUM CONTROL VALVE SET

Hide 16209 20.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343498C01
2.073,1.792 2.708,1.792 true 0.26,0.771 0.896,0.771 true 2.01,0.458 2.01,0.969 true 2.729,1.698 2.969,1.896 0.24,0.198 10 true *1 0.083,0.677 0.26,0.865 0.177,0.188 10 true *2 1.938,0.979 2.177,1.177 0.24,0.198 10 true *3
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


b.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


c.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


d.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 25800 21.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 22.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 23.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 24.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 26.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 27.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 28.REMOVE NO. 2 FUEL HOSE

Hide 23271H 29.REMOVE NO. 1 FUEL HOSE

Hide 23804D 30.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23815D 31.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 32.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 33.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 35.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 37.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 38.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A343500

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 39.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 40.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 41.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 42.REMOVE GLOW PLUG ASSEMBLY

Hide 44781 43.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300 44.REMOVE FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.
A347297

Remove the 2 nuts and fuel filter assembly from the cylinder block sub-assembly.


Hide 23780 45.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.
A343502

Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.


Hide 16025 46.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 47.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A343504

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422C 48.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 16282 49.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 50.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 23295D 51.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 52.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 16268 60.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A343505

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


Hide 16284 61.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 15407 64.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 83530 67.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 16207 68.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 69.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A365476C01
0.219,0.083 0.583,0.365 0.365,0.281 12 false *A 0.25,2.417 0.542,2.698 0.292,0.281 12 false *B
*A w/ DPF
*B w/o DPF


Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16321 70.REMOVE WATER INLET

a.
A343508

Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.


Hide 16331A 71.REMOVE THERMOSTAT

Hide 16603 72.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 73.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25706 74.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A343509

Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.


b.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 29300 75.REMOVE VACUUM PUMP ASSEMBLY

a.
A343510

Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.


b.

Remove the 2 O-rings from the vacuum pump assembly.


Hide 11382C 76.REMOVE CAMSHAFT OIL SEAL RETAINER

a.
A343511

Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 16575C 79.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.