1.INSTALL ENGINE HANGER
12361
2.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.
12391
3.INSTALL FRONT ENGINE MOUNTING HEAT INSULATOR RH
Install the front engine mounting heat insulator RH to the front engine mounting insulator with the bolt.
82121
4.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
11000
5.REMOVE ENGINE FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
11000
6.INSTALL ENGINE ASSEMBLY
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.
Remove the 2 bolts and 2 engine hangers.
11355
7.INSTALL REAR END PLATE
Install the rear end plate to the cylinder block with the bolt.
Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.
32101
8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
13405
9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
31250
10.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
31210
11.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
31210
12.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
35000
13.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
14.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
41110F
15.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
44250
16.INSTALL POWER STEERING LINK ASSEMBLY (for 4WD)
45219
17.CONNECT STEERING SLIDING YOKE (for 4WD)
43410D
18.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)
43420
19.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)
43410
20.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
89543
21.CONNECT FRONT SPEED SENSOR LH (for 4WD)
48069
22.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)
23.CONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)
43502H
24.INSTALL FRONT AXLE SHAFT NUT (for 4WD)
43514C
25.INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
37100
26.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
37100
27.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
51569
28.INSTALL PROPELLER SHAFT GUARD
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
37140
29.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
except TSAM Made:
51561D
30.INSTALL PROPELLER SHAFT GUARD (for 4WD)
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
except TSAM Made:
17410
31.INSTALL FRONT EXHAUST PIPE ASSEMBLY
32.CONNECT ENGINE WIRE
Connect the sensor bracket to the right side of the frame with the bolt.
Connect the air fuel ratio sensor connector.
Connect the wire clamp to the front engine mounting bracket LH with the bolt.
Attach the clamp.
Connect the 2 connectors to the engine room relay block.
Connect the engine wire to the engine room relay block with the nut.
Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.
Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.
Attach the clamp and install the No. 2 engine wire with the bolt.
Position the No. 2 engine wire as shown in the illustration.
Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.
Install the battery tray.
Install the battery.
Install the battery hold down clamp with the 2 nuts.
Tighten the nut and install the positive (+) battery terminal.
Position the positive (+) battery terminal as shown in the illustration.
Connect the engine room main wire to the positive (+) battery terminal with the nut.
Connect the connector to the engine room main wire.
Push the engine wire through the dash panel into the cabin.
The wire should be within the range shown in the illustration.
w/ Secondary Air Injection System:
Connect the engine wire to the air injection control bracket with the bolt.
Attach the clamp.
Connect the air injection control driver connector.
w/o Secondary Air Injection System:
Connect the engine wire to the air injection control bracket with the bolt.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
89661
33.INSTALL ECM
55550
34.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
23271H
35.CONNECT NO. 1 FUEL HOSE
23273C
36.CONNECT NO. 2 FUEL HOSE
17344
37.CONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)
44774
38.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose to the intake manifold, and slide the clamp to secure the hose.
39.CONNECT PURGE LINE HOSE
Connect the purge line hose to the purge VSV, and slide the clamp to secure the hose.
28100
40.INSTALL STARTER ASSEMBLY
for 2.0 kW Type:
Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for 2.0 kW Type)>INSTALLATION
except 2.0 kW Type:
Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(except 2.0 kW Type)>INSTALLATION
for BOSCH Made:
Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for BOSCH Made)>INSTALLATION
88320
41.CONNECT COOLER COMPRESSOR ASSEMBLY
11452
42.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Install a new O-ring and the engine oil level dipstick guide with the bolt.
15301
43.INSTALL ENGINE OIL LEVEL DIPSTICK
44320
44.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly with the 2 bolts.
Connect the power steering oil pressure switch connector.
45.CONNECT HEATER HOSE
Connect the heater water outlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
Connect the heater water inlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
16400
46.INSTALL RADIATOR ASSEMBLY
32941
47.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)
32942
48.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)
16711
49.INSTALL FAN SHROUD
16470
50.INSTALL RADIATOR RESERVOIR
17621A
51.CONNECT AIR PUMP INLET (w/ Secondary Air Injection System)
16572
52.INSTALL RADIATOR HOSE OUTLET
16571
53.INSTALL RADIATOR HOSE INLET
16593
54.INSTALL NO. 1 RADIATOR AIR GUIDE
53294C
55.INSTALL RADIATOR SIDE DEFLECTOR LH
53293C
56.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
17861
57.INSTALL INTAKE AIR CONNECTOR
17701
58.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Attach the 3 wire harness clamps.
17801
59.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner cap sub-assembly.
17705
60.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Install the air cleaner cap sub-assembly with air cleaner hose and tighten the hose clamp.
Attach the 4 clamps.
Connect the intake mass air flow meter connector and attach the 2 wire harness clamps.
53301
61.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose to the hood sub-assembly.
Adjust the hood sub-assembly.
62.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
63.ADD ENGINE OIL
64.ADD ENGINE COOLANT
33820B
65.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)
66.INSPECT SHIFT LEVER POSITION (for Automatic Transmission)
67.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
68.ADJUST AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
69.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)
for R151F:
Click hereDrivetrain>R151F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSMISSION OIL>REPLACEMENT
70.ADD DIFFERENTIAL OIL (for 4WD)
71.INSPECT FOR FUEL LEAK
72.INSPECT FOR OIL LEAK
73.INSPECT FOR COOLANT LEAK
74.INSPECT FOR EXHAUST GAS LEAK
75.INSPECT IGNITION TIMING
76.INSPECT ENGINE IDLE SPEED
77.CHECK CO/HC
22030
78.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY
53882F
79.INSTALL FRONT FENDER SEAL LH
Install the front fender seal LH with 6 new clips.
53882F
80.INSTALL FRONT FENDER SEAL RH
Install the front fender seal RH with 6 new clips.
53737B
81.INSTALL FRONT UPPER FENDER APRON SEAL LH
Install the front upper fender apron seal LH with 6 new clips.
53736
82.INSTALL FRONT UPPER FENDER APRON SEAL RH
w/ Secondary Air Injection System:
Install the front upper fender apron seal RH with 5 new clips.
w/o Secondary Air Injection System:
Install the front upper fender apron seal RH with 6 new clips.
51407A
83.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Cover)
51442
84.INSTALL NO. 2 ENGINE UNDER COVER
51410
85.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
86.CHECK ABS SPEED SENSOR SIGNAL (for 4WD)