Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2A00  A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).

DTC No. DTC Detection Condition Trouble Area
P2A00 Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor

·

Intake system

·

Fuel injector

·

Fuel pump

·

Fuel line

·

ECM



MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after the preconditions are met in order to measure the air fuel ratio sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the air fuel ratio sensor response rate. The ECM receives a signal from the air fuel ratio sensor while performing active A/F control and uses it to calculate the air fuel ratio sensor response rate deterioration level.

If the air fuel ratio sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.

A115363E87
4.26,1.5 4.125,1.115 false 4.51,1.74 4.74,1.125 false 0.104,0.052 2.333,0.25 2.229,0.198 12 false Air Fuel Ratio Sensor Output: 1,0.844 2.167,1.031 1.167,0.188 10 false Active A/F Control 0.354,1.771 2.188,1.958 1.833,0.188 10 false Air Fuel Ratio Sensor Output 3.635,1.042 4.135,1.229 0.5,0.188 10 false Normal 4.76,1.052 5.688,1.24 0.927,0.188 10 false Malfunctioning 4.083,0.156 5.802,0.344 1.719,0.188 10 false Approximately 10 Seconds 0.792,2.74 2.167,2.927 1.375,0.188 10 false Fuel Injection Volume 2.896,2.5 3.542,2.688 0.646,0.188 10 false Increase 2.896,2.958 3.542,3.146 0.646,0.188 10 false Decrease 4.76,0.75 5.156,0.896 0.396,0.146 10 false ON 2.719,0.49 3.094,0.677 0.375,0.188 10 false OFF

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active A/F control Executing
Active A/F control performed when following conditions met -
Engine coolant temperature 75°C (167°F) or higher
Idle OFF
Engine speed 1000 to 4000 rpm
Air fuel ratio sensor status Activated
Engine load 10 to 70%
Transmission gear 2nd or higher
Catalyst monitor Not executed
Intake air amount 10.8 to 43.1 gm/sec

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


C358633E01
1.26,0.969 1.885,0.479 1.885,0.479 2.083,0.479 false 0.219,0.146 2.208,0.344 1.99,0.198 10 false Vehicle Speed 2.146,0.406 4.896,0.656 2.75,0.25 10 false Between 75 and 100 km/h (47 and 63 mph) 0.135,1.24 1.458,1.49 1.323,0.25 10 false 60 km/h (38 mph) 0.875,2.323 1.792,2.521 0.917,0.198 10 false Idling 0.146,2.542 1.344,2.792 1.198,0.25 10 false Ignition Switch off 1.74,2.813 3.271,3.01 1.531,0.198 10 false Warming up 1.99,2.198 2.448,2.396 0.458,0.198 10 false [A] 3.438,1.375 3.896,1.573 0.458,0.198 10 false [B] 5.958,1 6.417,1.198 0.458,0.198 10 false [D] 4.333,3.229 4.792,3.427 0.458,0.198 10 false [C] 2.938,2.833 4.26,3.115 1.323,0.281 10 false 10 minutes or more 5.479,2.833 6.823,3.115 1.344,0.281 10 false 10 minutes or more 6.708,3.229 6.958,3.479 0.25,0.25 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more in a city area [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2A00.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.



14.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2A00.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Sensor 1 refers to the sensor mounted in front of the Three-way Catalytic Converter (TWC) and located near the engine assembly.

·

DTC P2A00 may be stored when the air-fuel ratio is stuck at a rich or lean value.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P2A00 is output A
P2A00 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean/Rich Lean/Rich Normal A
Lean Lean Actual air fuel ratio lean B
Rich Rich Actual air fuel ratio rich B
Lean Lean/Rich Air fuel ratio sensor malfunction C
Rich Lean/Rich Air fuel ratio sensor malfunction C


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)

B

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

C

8.REPLACE AIR FUEL RATIO SENSOR
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2A00.


j.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2A00 is output) B



A

B

8.REPLACE AIR FUEL RATIO SENSOR
4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

5.CHECK INTAKE SYSTEM

NG

5.CHECK INTAKE SYSTEM
a.

Check for vacuum leaks in the intake system.

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

6.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FUEL PRESSURE

OK

7.INSPECT FUEL INJECTOR ASSEMBLY

NG

12.INSPECT FUEL PUMP
7.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

8.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

8.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2A00.


j.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2A00 is output) A
NORMAL (DTC is not output) B



A

10.REPLACE ECM

B

END

10.REPLACE ECM

NEXT

11.PERFORM CONFIRMATION DRIVING PATTERN
11.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2A00.


j.

Check that the DTC judgment result is NORMAL.



NEXT

END

12.INSPECT FUEL PUMP
a.

Inspect the fuel pump.



Result:
Result Proceed to
OK A
NG
(for 5 door)
B
NG
(for 3 door)
C


HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

REPAIR OR REPLACE FUEL LINE

B

C