Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List MAP

Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

ECM not operating well

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP
·

With the engine switch on (IG) or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet
Data List Battery Voltage
When cranking, battery voltage is below 5 V.

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.



Start System
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter Signal
·

Engine switch on (STA) output:

ON: Starter is operating

OFF: Starter is not operating




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.



Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Fuel filter element assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Pressure Discharge Valve
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Common Rail Pressure decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Valve Pos
·

Generally, Actual EGR Valve Pos. = Target EGR Valve Pos +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Valve Pos (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the engine switch is turned to on (IG) (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Lrn. Val.,
·

When leaving the vehicle idling the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position

0%: Fully closed

100%: Fully open

·

When the engine switch on (IG) (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the engine switch is turned from on (IG) to off, the throttle is fully closed temporarily.





Data List Related to Starting Trouble


·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Battery Voltage

·

Starter Signal

·

Engine Speed of Cyl #1 (to #4)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Common Rail Pressure

·

Common Rail Pressure

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Valve Pos

·

Actual EGR Valve Pos

·

EGR Close Lrn. Val.



CAUTION / NOTICE / HINT

Explanation of Symptom



Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated by compression pressure. With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause



A210593E45
0.844,8.5 1.031,8.667 0.188,0.167 10 false A 3.594,0.948 5.208,1.135 1.615,0.188 10 false Depleted battery 0.25,0.115 1.281,0.302 1.031,0.188 10 false Difficult to start 0.865,0.927 2.25,1.094 1.385,0.167 10 false Does not crank at all 0.771,4.094 2.396,4.281 1.625,0.188 10 false Cranking speed too slow 0.792,5.594 2.813,5.781 2.021,0.188 10 false Difficult to start (cranking is OK) 3.594,1.688 6.021,1.896 2.427,0.208 10 false ECM power supply circuit malfunction 3.594,2.479 6.229,2.677 2.635,0.198 10 false Clutch start switch assembly malfunction 3.594,3.167 6.031,3.5 2.438,0.333 10 false Immobiliser system or entry and start system fault 3.594,4.083 4.854,4.271 1.26,0.188 10 false Depleted battery 4.115,6.521 6.781,6.698 2.667,0.177 10 false Fuel is not supplied to fuel supply pump 1.719,6.521 3.052,6.688 1.333,0.167 10 false Fuel pressure is low 4.115,7.292 6.021,7.5 1.906,0.208 10 false Fuel supply pump malfunction 4.115,8.063 6.385,8.26 2.271,0.198 10 false Common rail assembly malfunction 3.594,4.865 6.365,5.219 2.771,0.354 10 false Increased internal friction of the engine mechanical parts (oil too thick, seizure, etc.)

A183464E33
0.844,0.094 1,0.26 0.156,0.167 10 false A 4.188,0.729 6.292,0.917 2.104,0.188 10 false Injector power circuit malfunction 1.76,0.781 3.115,0.948 1.354,0.167 10 false Fuel pressure is high 4.177,1.5 5.667,1.708 1.49,0.208 10 false Air in injector assembly 4.198,2.354 6.115,2.542 1.917,0.188 10 false Injector assembly malfunction 1.771,2.396 3.156,2.594 1.385,0.198 10 false Specific cylinder fault 4.188,3.104 5.927,3.313 1.74,0.208 10 false Low compression pressure 4.188,3.969 5.813,4.156 1.625,0.188 10 false Glow system malfunction 1.76,4.01 3.406,4.208 1.646,0.198 10 false Difficult to start when cold 4.177,4.719 6.406,5.073 2.229,0.354 10 false Engine coolant temperature sensor malfunction 1.76,6.094 2.854,6.292 1.094,0.198 10 false Poor fuel quality

NOTICE:


HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result
Result Proceed to
Cranking is OK. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Does not crank at all. C



A

2.READ ALL OUTPUT DTCS

B

C

31.READ OUTPUT DTC (RELATED TO ENGINE)
2.READ ALL OUTPUT DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check the DTCs.

Result
Result Proceed to
No DTC is output A
Engine related DTCs are output B

HINT:

If only DTC P1604 is output, proceed to step 3.




A

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

B

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Starting.


d.

Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.





NEXT

4.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
4.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
a.

Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was started.

A227761E04
2.385,0.844 2.469,0.844 2.469,0.844 2.417,1.188 false 2.813,0.542 2.74,0.594 false 4.146,0.583 4.021,0.583 4.021,0.583 3.802,0.771 false 4.01,2.344 3.917,2.344 3.917,2.344 3.802,2.229 false 3.938,2.875 3.865,2.875 3.865,2.875 3.792,2.792 false 5.563,0.406 5.406,0.406 5.406,0.406 5.094,0.927 false 5.667,1.469 5.573,1.469 5.573,1.469 5.417,1.24 false 5.594,2.177 5.479,2.177 5.479,2.177 5.25,1.51 false 1.938,2.333 2.083,2.333 2.083,2.333 2.281,2.99 false 5.292,2.646 5.479,2.177 false 0.052,1.74 0.906,2.198 0.854,0.458 10 Common Rail Pressure 3.969,2.792 4.104,2.969 0.135,0.177 10 a 2.844,0.469 2.99,0.646 0.146,0.177 10 b 4.198,0.5 4.365,0.667 0.167,0.167 10 d 4.052,2.271 4.198,2.448 0.146,0.177 10 c 1.073,0.771 2.344,1.135 1.271,0.365 10 Target Common Rail Pressure 5.594,0.344 7.063,0.698 1.469,0.354 10 Abnormal Common Rail Pressure 1.083,2.229 1.948,2.552 0.865,0.323 10 Engine cranking start 2.469,3.198 3.573,3.375 1.104,0.177 10 About 2 seconds 5.594,2.104 7.083,2.479 1.49,0.375 10 Abnormal Common Rail Pressure 5.719,1.417 7.042,1.781 1.323,0.365 10 Normal Common Rail Pressure

Result
Result Proceed to
At the point in the illustration labeled "a", Common Rail Pressure is less than 10000 kPa from the value of Common Rail Pressure when cranking started A
At the point in the illustration labeled "c", Common Rail Pressure is below Target Common Rail Pressure by 15000 kPa or more B
Common Rail Pressure increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Common Rail Pressure is higher than Target Common Rail Pressure C
Except above D

HINT:
·

Even if Common Rail Pressure is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the fuel supply pump is normal.

·

Fuel pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.

·

Fuel pressure increases rapidly during cranking.





A

5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

B

13.READ VALUE USING GTS (COMMON RAIL PRESSURE)

C

25.INSPECT INJECTOR POWER SOURCE CIRCUIT

D

16.READ VALUE USING GTS (INJECTOR FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.


HINT:
·

When there is a lack of fuel, fuel pressure drops.

·

Inspect for fuel filter clogging (check that the fuel filter is not clogged).




c.

Reconnect the inlet hose.



OK

6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

11.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r6-1 - C150-3 (PCV+) Always Below 1 Ω
r6-2 - C150-4 (PCV-) Always Below 1 Ω
r6-1 or C150-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
r6-2 (PCV) or C150-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the pre-stroke control valve connector.


e.

Reconnect the ECM connector.



OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

9.READ VALUE USING GTS (COMMON RAIL PRESSURE)
9.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure.


d.

Start the engine.


e.

Read the values while cranking and idling the engine.

Result
Result Proceed to
The engine cannot be started or the engine can be started but Common Rail Pressure is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A



A

END

B

10.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
10.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly for all the cylinders (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.




c.

Install the glow plug assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>INSTALLATION).



NEXT

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
11.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
a.

Check and repair or replace the clogged fuel pipe.



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was warmed up.

Result
Result Proceed to
Difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more A
Except above B



A

14.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)

B

15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
14.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.





NEXT

21.REPLACE FUEL FILTER ELEMENT ASSEMBLY
16.READ VALUE USING GTS (INJECTOR FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
a.

Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.

Result
Result Proceed to
Injection Feedback Val #1 to #4 are 3 mm3/st or less.
Injection Volume is more than 10 mm3/st.
A*
Injection Feedback Val for at least one cylinder is more than +3 mm3/st
HINT:

There may be a malfunction in the corresponding cylinder.


B
Except above C

HINT:
·

*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, lack of power.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.





A

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

18.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

27.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.





NEXT

21.REPLACE FUEL FILTER ELEMENT ASSEMBLY
18.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch to on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.


d.

Check the engine speed during the Active Test.

Result
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other. B

HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

19.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
19.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the injector assembly of malfunctioning cylinder (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.





NEXT

21.REPLACE FUEL FILTER ELEMENT ASSEMBLY
21.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT).



NEXT

22.BLEED AIR FROM FUEL SYSTEM
22.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

23.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
23.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END

25.INSPECT INJECTOR POWER SOURCE CIRCUIT
a.

Perform troubleshooting for DTC P062D during a startability malfunction, even if DTC P062D is not output (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0201).

When troubleshooting the injector power source circuit, check the following locations, as one may contain the cause of the malfunction


·

EDU relay

·

Injector assembly circuit

·

ECM


HINT:
·

When the engine cannot be started due to a malfunction in the injector power source circuit, once the DTCs are cleared, P062D cannot be stored even when the problem symptoms are reproduced and a startability malfunction occurs.

Since P062D cannot be stored when starting the engine, fuel injection cannot be performed even though fuel injection signals are output from the ECM. Therefore, using the GTS during a startability malfunction to check the data shows that an excessive amount of fuel is supplied to the common rail assembly by the fuel supply pump assembly, and as a result, the Common Rail Pressure is higher than the Target Common Rail Pressure.

·

Perform the following procedure when a malfunction cannot be found during the troubleshooting procedure for P062D and the Common Rail Pressure when starting the engine is higher than the Target Common Rail Pressure.

·

Perform the troubleshooting procedure for DTC P062D and proceed to the diagnostic flow situations where the engine does not start.




A

26.INSPECT INJECTOR ASSEMBLY

B

REPAIR OR REPLACE MALFUNCTIONING PARTS

26.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connectors.


b.

Measure the resistance of the injector assembly.

OK:

No open circuit malfunction.



c.

Reconnect the injector assembly connectors.



OK

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

20.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
27.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.


Result
Result Proceed to
Difficult to start only for cold engine. A
Difficult to start both for cold and warmed up engine. B


A

28.READ VALUE USING GTS (COOLANT TEMP)

B

30.CHECK FUEL QUALITY
28.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Starting / Coolant Temp.


d.

Read the value displayed on the GTS.

OK:

Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up




OK

29.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

29.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

OK

30.CHECK FUEL QUALITY

NG

30.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.



NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
Engine related DTCs are output B



A

32.CHECK COMMUNICATION BETWEEN GTS AND ECM

B

GO TO DTC

32.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a GTS that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).




OK

33.READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL OR CLUTCH SWITCH)

NG

33.READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL OR CLUTCH SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal and Neutral Position SW Signal.


d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Starter Signal Cranking ON
Neutral Position SW Signal*1 Shift lever in neutral ON
Clutch Switch*2 Clutch pedal depressed ON


*1: only for Automatic transmission

*2: only for Manual transmission

Result
Result Proceed to
OK A
NG (for Manual transmission) B
NG (for Automatic transmission) C



A

34.CHECK STARTING SYSTEM

B

INSPECT CLUTCH SWITCH ASSEMBLY

C

34.CHECK STARTING SYSTEM
a.

Inspect the starting system.

HINT:

Be sure to inspect the following areas:

·

Battery

·

Starter relay

·

Starter assembly

·

Entry and start system

·

Immobiliser system





NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END