Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260507 CYLINDER HEAD GASKET A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft, No. 2 camshaft or cylinder head sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Clean and degrease the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


b.
A337677E04
2.448,0.958 2.802,0.344 2.802,0.344 2.927,0.344 true 0.49,1.177 0.604,1.177 0.604,1.177 0.74,0.823 false 2.958,0.25 3.177,0.469 0.219,0.219 10 false *a 3.177,0.938 3.385,1.135 0.208,0.198 10 false *b 1.229,0.677 1.438,0.885 0.208,0.208 10 false *c 1.24,3.021 1.49,3.208 0.25,0.188 10 false *d 2.76,3 2.99,3.208 0.229,0.208 10 false *e 2.354,1.49 2.552,1.688 0.198,0.198 10 false *a 0.292,1.083 0.49,1.281 0.198,0.198 10 false *1 0.677,0.292 0.875,0.49 0.198,0.198 10 false *f 2.104,0.458 2.302,0.656 0.198,0.198 10 false *g 2.927,2.521 3.125,2.719 0.198,0.198 10 false *g

Apply seal packing to a new cylinder head gasket as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207 B or equivalent.


Text in Illustration
*1 Cylinder Head Gasket
*a 7.0 to 9.0 mm (0.276 to 0.354 in.)
*b 5.0 to 7.0 mm (0.197 to 0.276 in.)
*c 3.0 to 5.0 mm (0.118 to 0.197 in.)
*d 166.25 mm (6.55 in.)
*e 62.25 mm (2.46 in.)
*f Side View
*g View A

NOTICE:
·

Be sure to clean and degrease the contact surfaces.

·

Apply seal packing to the bead on the cylinder head gasket.

·

Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes after applying seal packing.




c.
A384441E01
0.698,0.625 0.927,0.292 0.927,0.292 1.115,0.292 true 1.156,0.188 1.365,0.396 0.208,0.208 10 false *a

Place the cylinder head gasket on the cylinder block surface with the lot No. stamp facing upward.

Text in Illustration
*a Lot No.
V100135

Engine Front

NOTICE:
·

Remove any oil from the contact surface.

·

Make sure that the cylinder head gasket is installed in the correct direction.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).

·

The cylinder head bolts are tightened in 3 successive steps.



a.

Place the cylinder head sub-assembly on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block gently so as not to damage the gasket with the bottom part of the cylinder head sub-assembly.




b.

Install the plate washers to the cylinder head set bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.
A384511E02
0.469,1.75 0.74,2.01 0.271,0.26 10 true 10 2.99,0.26 3.146,0.458 0.156,0.198 10 false 9 0.51,0.26 0.667,0.458 0.156,0.198 10 true 8 3.01,1.75 3.167,1.948 0.156,0.198 10 false 7 1.156,0.25 1.313,0.448 0.156,0.198 10 false 6 2.375,1.76 2.531,1.958 0.156,0.198 10 false 5 1.115,1.76 1.271,1.958 0.156,0.198 10 false 4 2.354,0.25 2.51,0.448 0.156,0.198 10 true 3 1.75,1.76 1.906,1.958 0.156,0.198 10 false 2 1.75,0.25 1.969,0.469 0.219,0.219 10 false 1

Step 1:

Using several steps, install and uniformly tighten the 10 cylinder head set bolts with plate washers in the sequence shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


e.

Mark the front of each cylinder head set bolt head with paint.


f.

Step 2:

Tighten the cylinder head set bolts 90° in the sequence shown in step 1.


g.

Step 3:

Tighten the cylinder head set bolts another 90° in the sequence shown in step 1.


h.

Check that the paint marks are now at a 180° angle to the front.


i.

w/ Oil Cooler:

Connect the No. 4 water by-pass pipe with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 3.CONNECT ENGINE WIRE

a.

Connect the engine wire to the cylinder head sub-assembly with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 13716 4.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 5.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect each valve lash adjuster assembly before installing it (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 6.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply clean engine oil to the valve lash adjuster assembly tips and valve stem cap surfaces.


b.
A336446E03
0.76,2.552 0.927,2.552 0.927,2.552 1.104,2.25 false 0.865,3.042 1.146,3.042 1.146,3.042 1.333,2.74 true 1.917,2.177 2.438,2.177 true 0.625,0.813 0.781,0.813 0.781,0.813 0.969,0.51 false 0.865,1.281 1.146,1.281 1.146,1.281 1.323,0.979 true 1.917,0.406 2.448,0.406 true 0.031,0 0.302,0.25 0.271,0.25 10 false *a 0.021,1.802 0.292,2.052 0.271,0.25 10 false *b 0.552,2.469 0.74,2.646 0.188,0.177 10 false *1 0.656,2.948 0.854,3.125 0.198,0.177 10 false *2 2.469,2.094 2.708,2.292 0.24,0.198 10 false *3 0.417,0.729 0.604,0.906 0.188,0.177 10 false *1 0.656,1.198 0.854,1.375 0.198,0.177 10 false *2 2.479,0.313 2.719,0.51 0.24,0.198 10 false *3

Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

Text in Illustration
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a INCORRECT
*b CORRECT

NOTICE:

Install the valve stem cap, valve lash adjuster assembly and No. 1 valve rocker arm sub-assembly to the same places they were removed from.



Hide 13511 7.INSTALL CAMSHAFTS

HINT:

Perform "Inspection After Repairs" after replacing the camshaft or No. 2 camshaft (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.
U147710E03
0.292,0.208 0.458,0.396 0.167,0.188 10 false A 1.99,0.208 2.177,0.406 0.188,0.198 10 false C 1.99,1.51 2.167,1.698 0.177,0.188 10 false D 0.292,1.51 0.458,1.708 0.167,0.198 10 false B 1.146,2.823 1.302,3.021 0.156,0.198 10 false A 1.76,2.5 1.917,2.688 0.156,0.188 10 false B 2.667,3.542 2.833,3.75 0.167,0.208 10 true C 3.042,3.26 3.229,3.458 0.188,0.198 10 false D

Apply clean engine oil to the camshaft cams and cylinder head journals.


b.

Position the camshaft and No. 2 camshaft as shown in the illustration.


c.
A336446E03
0.76,2.552 0.927,2.552 0.927,2.552 1.104,2.25 false 0.865,3.042 1.146,3.042 1.146,3.042 1.333,2.74 true 1.917,2.177 2.438,2.177 true 0.625,0.813 0.781,0.813 0.781,0.813 0.969,0.51 false 0.865,1.281 1.146,1.281 1.146,1.281 1.323,0.979 true 1.917,0.406 2.448,0.406 true 0.031,0 0.302,0.25 0.271,0.25 10 false *a 0.021,1.802 0.292,2.052 0.271,0.25 10 false *b 0.552,2.469 0.74,2.646 0.188,0.177 10 false *1 0.656,2.948 0.854,3.125 0.198,0.177 10 false *2 2.469,2.094 2.708,2.292 0.24,0.198 10 false *3 0.417,0.729 0.604,0.906 0.188,0.177 10 false *1 0.656,1.198 0.854,1.375 0.198,0.177 10 false *2 2.479,0.313 2.719,0.51 0.24,0.198 10 false *3

Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.

Text in Illustration
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a INCORRECT
*b CORRECT


Hide 8.INSTALL CAMSHAFT BEARING CAP

a.
A336457

Temporarily install the No. 1 camshaft bearing cap.


b.

Confirm the location for each No. 2 camshaft bearing cap and install each one to the proper location.


c.

Uniformly temporarily install the 20 bolts while keeping the camshaft level.


d.
U147708E03
1.594,0.219 1.719,0.417 0.125,0.198 10 false 4 0.938,1.813 1.167,2.01 0.229,0.198 10 false 10 1.604,1.802 1.729,1.99 0.125,0.188 10 false 2 2.792,1.792 3.01,1.99 0.219,0.198 10 false 14 2.219,1.813 2.365,2.01 0.146,0.198 10 false 6 2.198,0.229 2.333,0.417 0.135,0.188 10 false 8 0.948,0.219 1.156,0.417 0.208,0.198 10 false 12 2.552,0.969 2.802,1.188 0.25,0.219 10 false 13 1.167,1.104 1.385,1.292 0.219,0.188 10 false 11 1.802,1.083 1.958,1.292 0.156,0.208 10 false 3 1.979,0.969 2.156,1.177 0.177,0.208 10 false 5 1.385,0.938 1.542,1.125 0.156,0.188 10 false 1 0.698,0.99 0.844,1.198 0.146,0.208 10 false 9 2.438,1.083 2.604,1.271 0.167,0.188 10 false 7 0.458,0.167 0.677,0.365 0.219,0.198 10 false 20 0.167,0.646 0.396,0.854 0.229,0.208 10 false 18 0.167,1.427 0.396,1.635 0.229,0.208 10 false 17 0.458,1.885 0.667,2.073 0.208,0.188 10 true 19 3.042,1.115 3.292,1.344 0.25,0.229 10 false 15 2.76,0.229 2.979,0.427 0.219,0.198 10 false 16

Tighten the 20 bolts in the order shown in the illustration.

Torque:
16 N*m (158 kgf*cm, 11 ft.*lbf)


Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11204 15.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 11302 16.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12229 17.INSTALL VENTILATION PIPE

a.

Install the ventilation pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the cylinder head sub-assembly, and slide the clip to secure the hose.


c.

Connect the No. 3 ventilation hose to the ventilation pipe, and slide the clip to secure the hose.


d.

Connect the No. 1 ventilation hose to the PCV valve sub-assembly, and slide the clip to secure the hose.


e.

Connect the No. 1 water by-pass hose to throttle body with motor assembly, and slide the clip to secure the hose.


Hide 17167 22.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR