Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260500 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 13471A 1.INSTALL CRANKSHAFT PULLEY SET KEY

a.

Install the 2 pulley keys to the crankshaft.


Hide 13554 2.INSTALL NO. 4 CHAIN VIBRATION DAMPER

a.

Install the vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13507 3.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
A101978

Install the timing sprocket as shown in the illustration.

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balanceshafts are at the bottom.


HINT:

Install the timing sprocket with the front mark facing forward.



b.
A336860E02
2.75,0.344 1.417,0.094 1.417,0.094 1.271,0.094 false 2.771,0.583 3.01,1.375 3.01,1.375 3.156,1.375 false 2.698,2.604 2.948,1.813 2.948,1.813 3.083,1.813 false 2.5,2.792 2.115,3.271 false 2.729,2.813 2.125,3.271 2.125,3.271 1.979,3.271 false 1.063,0 1.25,0.177 0.188,0.177 10 false *a 3.156,1.281 3.344,1.458 0.188,0.177 10 false *b 3.135,1.74 3.323,1.917 0.188,0.177 10 false *b 1.771,3.177 1.958,3.354 0.188,0.177 10 false *a

As shown in the illustration, install the chain to the sprocket and gear with the mark plates aligned with the timing marks on the sprocket and gear.

Text in Illustration
*a Mark Plate (Yellow)
*b Timing Mark


c.
A336861E02
0.406,0.896 0.542,1.573 0.542,1.573 0.677,1.573 false 0.604,0.677 1.052,0.115 1.052,0.115 1.156,0.115 false 0.76,1.49 0.979,1.677 0.219,0.188 10 false *a 1.198,0.042 1.417,0.229 0.219,0.188 10 false *b

Fit the other mark link of the chain behind the large timing mark of the balanceshaft drive gear.

Text in Illustration
*a Mark Plate (Yellow)
*b Large Timing Mark


d.

Insert the balanceshaft drive gear shaft through the balanceshaft drive gear so that it fits into the thrust plate hole.


e.
A336862E02
0.688,0.625 1.271,0.135 1.271,0.135 1.385,0.135 false 0.969,0.938 1.552,0.708 1.552,0.708 1.688,0.708 false 0.927,1.104 1.552,0.708 false 0.521,0.854 0.396,1.646 0.396,1.646 0.302,1.646 false 1.427,0.052 1.635,0.25 0.208,0.198 10 false *a 1.729,0.625 1.917,0.792 0.188,0.167 10 false *b 0.094,1.563 0.26,1.729 0.167,0.167 10 false *c

Align the small timing mark of the balanceshaft drive gear with the large timing mark of the balanceshaft timing gear.

Text in Illustration
*a Large Timing Mark
*b Small Timing Mark
*c Mark Plate (Yellow)


f.

Install the bolt to the balanceshaft drive gear.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


g.
A336863E02
0.583,0.531 1.031,0.115 1.031,0.115 1.135,0.115 false 0.813,0.792 1.302,0.615 1.302,0.615 1.406,0.615 false 0.781,0.938 1.302,0.615 false 0.427,0.719 0.313,1.25 0.313,1.25 0.198,1.25 false 2.844,0.281 2.313,0.104 2.313,0.104 2.208,0.104 false 2.813,0.531 2.073,0.396 2.073,0.396 1.958,0.396 false 2.792,2.688 3.052,1.896 3.052,1.896 3.135,1.896 false 2.865,2.875 2.396,3.281 2.396,3.281 2.281,3.281 false 2.594,2.896 2.396,3.281 false 1.177,0.021 1.365,0.177 0.188,0.156 10 false *a 1.469,0.542 1.656,0.698 0.188,0.156 10 false *b 0.021,1.167 0.188,1.323 0.167,0.156 10 false *c 2.01,0.021 2.177,0.177 0.167,0.156 10 false *c 1.771,0.344 1.938,0.5 0.167,0.156 10 false *d 3.156,1.823 3.323,1.979 0.167,0.156 10 false *d 2.083,3.177 2.26,3.354 0.177,0.177 10 false *c

Check that each timing mark is aligned with the corresponding mark link.

Text in Illustration
*a Large Timing Mark
*b Small Timing Mark
*c Mark Plate (Yellow)
*d Timing Mark

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balanceshafts are at the bottom.



Hide 13550 4.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A384434

Install the chain tensioner assembly with the nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Install the chain tensioner with the pin installed, and then remove the pin after installation. When performing this step, do not push the vibration damper against the chain.



b.
A101320E09
0.02,0.461 0.201,0.661 0.182,0.201 10 *a 0.454,1.78 0.647,1.981 0.193,0.201 10 *b 1.007,1.146 0.842,1.895 0.842,1.895 0.685,1.895 false 0.625,1.17 0.386,0.604 0.386,0.604 0.237,0.604 false

Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.

Text in Illustration
*a Plunger
*b Stopper Plate


c.

Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.


Hide 13563 5.INSTALL NO. 3 CHAIN VIBRATION DAMPER

a.
A384435

Install the chain vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13562 6.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.
A384445

Install the chain vibration damper with the bolt.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)


Hide 15678A 7.INSTALL OIL CONTROL VALVE FILTER

a.

Check that no foreign matter is on the mesh part of the filter.

If foreign matter is present, clean the part thoroughly.


b.

Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 13070A 10.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 11.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13521 17.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A101308

Install the crankshaft timing gear or sprocket as shown in the illustration.


Hide 13561 18.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the bolt and nut.

Torque:
for bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Remove the hexagon wrench from the No. 2 chain tensioner assembly and release the plunger.


Hide 13506 19.INSTALL CHAIN SUB-ASSEMBLY

a.
A384436E01
2.708,0.938 2.073,0.792 2.073,0.792 2.698,0.698 true 1.125,0.573 1.385,1.125 1.385,1.125 1,0.781 true 0.406,2.021 0.573,2.021 0.573,2.021 0.875,2.26 true 0.344,2.885 0.448,2.885 0.448,2.885 0.896,2.333 true 2.5,2.26 2.792,2.073 2.792,2.073 2.979,2.073 true 2.5,2.375 3.042,2.865 3.042,2.865 3.167,2.865 true 1.75,3.927 2.406,3.604 2.406,3.604 2.594,3.604 true 1.885,4.042 2.052,4.292 2.052,4.292 2.052,4.427 true 1.823,4.031 1.552,4.531 1.552,4.531 1.427,4.531 true 1.24,4.438 1.438,4.656 0.198,0.219 10 false *a 0.198,1.927 0.396,2.146 0.198,0.219 10 false *b 1.979,4.448 2.177,4.667 0.198,0.219 10 false *c 1.042,0.083 1.24,0.302 0.198,0.219 10 false *d 1.802,3.302 2,3.521 0.198,0.219 10 true *e 2.635,3.51 2.833,3.729 0.198,0.219 10 false *1 0.146,2.781 0.344,3 0.198,0.219 10 false *a 1.875,0.688 2.073,0.906 0.198,0.219 10 false *a 1.417,1.063 1.615,1.281 0.198,0.219 10 false *a 3.021,1.979 3.219,2.198 0.198,0.219 10 false *b 3.198,2.75 3.396,2.969 0.198,0.219 10 false *a

As shown in the illustration, install the chain sub-assembly to the camshaft timing exhaust gear assembly and camshaft timing gear assembly with the mark plates aligned with the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly.

Text in Illustration
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Mark Plate (Pink)
*c Mark Plate (Yellow)
*d Approximately 13°
*e Approximately 30°

HINT:
·

The camshaft mark plate is pink.

·

The crankshaft mark plate is yellow.




b.
A101359

Use a rope to tie the chain sub-assembly of the crankshaft timing gear or sprocket. Tie the rope near the crankshaft timing gear or sprocket.

NOTICE:

After the chain tensioner has been installed, the rope must be removed.


HINT:

The rope is tied so that the chain sub-assembly will not jump a tooth.



Hide 13559 20.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 21.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A101303E27
2.292,0.813 2.604,0.313 2.604,0.313 2.698,0.313 false 1.771,1.552 1.938,1.896 1.938,1.896 2.063,1.896 false 0.573,1.813 0.573,1.51 false 2.74,0.208 2.958,0.417 0.219,0.208 10 false *a 2.104,1.802 2.365,2.021 0.26,0.219 10 false *b 0.521,1.844 0.781,2.063 0.26,0.219 10 false *c

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.

Text in Illustration
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the No. 1 chain tensioner assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the No. 1 chain tensioner assembly and release the plunger.


Hide 22.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A384437E02
2.031,4.385 2.031,4.281 2.031,4.281 1.833,4.031 true 2.917,3.677 2.74,3.677 2.74,3.677 1.771,3.917 true 2.927,2.083 2.75,2.083 2.75,2.083 2.49,2.375 true 0.5,2.063 0.615,2.063 0.615,2.063 0.906,2.323 true 1.01,0.781 1.385,0.917 1.385,0.917 1.125,0.573 true 2.708,0.958 2.104,0.25 2.104,0.25 2.708,0.698 true 2.948,3.583 3.146,3.781 0.198,0.198 10 false *1 0.292,1.948 0.49,2.146 0.198,0.198 10 false *a 1.042,0.094 1.24,0.292 0.198,0.198 10 false *b 1.802,3.323 2,3.521 0.198,0.198 10 true *c 2.958,1.958 3.156,2.156 0.198,0.198 10 false *a 1.417,0.833 1.615,1.031 0.198,0.198 10 false *a 1.917,0.146 2.115,0.344 0.198,0.198 10 false *a 1.979,4.396 2.177,4.594 0.198,0.198 10 false *a

Check that the No. 1 cylinder is set to TDC/compression.

i.

Rotate the crankshaft two full rotations, and then check that all timing marks are in the position shown in the illustration.

If the timing marks do not match, set the chain sub-assembly again.

Text in Illustration
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°



Hide 13566B 23.INSTALL TIMING CHAIN GUIDE

a.

Install a new O-ring to the No. 1 camshaft bearing cap.


b.

Install the timing chain guide with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11204 24.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.

Install a new No. 2 camshaft bearing cap oil hole gasket and 3 new No. 3 camshaft bearing cap oil hole gaskets to the No. 1 camshaft bearing cap.


b.

Install the cylinder head cover connector sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16100 25.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11302 26.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16620D 27.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11432A 29.INSTALL NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)

a.

Install the No. 1 taper screw plug to the cylinder block.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 15777E 30.INSTALL UNION (w/ Oil Cooler)

a.

Install the union to the cylinder block.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 15609 31.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Using a hexagon wrench, install the oil filter bracket union.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Install a new oil filter bracket gasket to the oil filter bracket.


c.

Install a new O-ring to the oil filter bracket union.

NOTICE:

Apply a light coat of engine oil to the O-ring and oil filter bracket.



d.

Install 2 new gaskets and the 2 screw plugs to the oil filter bracket.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Install the oil filter bracket with the 2 bolts and nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 15600A 32.INSTALL OIL FILTER UNION (w/o Oil Cooler)

a.

Using a 27 mm socket wrench, install the oil filter union.

Torque:
43 N*m (439 kgf*cm, 32 ft.*lbf)


Hide 15710 33.INSTALL OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 16288 34.INSTALL NO. 4 WATER BY-PASS PIPE (w/ Oil Cooler)

a.

Install the No. 4 water by-pass pipe with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 5 water by-pass hose to the oil cooler assembly, and slide the clip to secure the hose.


Hide 16281 35.INSTALL NO. 4 WATER BY-PASS HOSE (w/ Oil Cooler)

a.

Install the No. 4 water by-pass hose to the oil cooler assembly and union, and slide the clips to secure the hoses.


Hide 83530 39.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 11381 40.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Clean and degrease the contact surfaces of the rear engine oil seal retainer and cylinder block sub-assembly.


b.
A346838E01
0.937,1.835 1.145,2.011 0.208,0.177 10 *a

Apply seal packing in a continuous bead as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Text in Illustration
*a Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




c.

Install the rear engine oil seal retainer with the 6 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11421 42.INSTALL OIL PAN STUD BOLT

NOTICE:

If a stud bolt is deformed or threads are damaged, replace it.


A337637E05
1.615,2.49 1.844,2.719 0.229,0.229 10 false *a 2.208,2.646 2.427,2.865 0.219,0.219 10 false *b 1.615,2.854 1.865,3.083 0.25,0.229 10 false *a

a.

Using E6 "TORX" socket wrench, install the stud bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

Text in Illustration
*a 9.0 mm (0.354 in.)
*b 19.0 mm (0.748 in.)


Hide 15104 43.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
U147711E05
0.865,0.031 1.052,0.208 0.188,0.177 10 false 1 0.115,0.427 0.313,0.615 0.198,0.188 10 false 2 2.521,1.344 2.688,1.521 0.167,0.177 10 true 3 1.833,0.177 2.021,0.365 0.188,0.188 10 false 4 2.646,0.542 2.813,0.719 0.167,0.177 10 true 5 1.469,1.365 1.635,1.542 0.167,0.177 10 false 6

Install the oil strainer sub-assembly with the 6 bolts, and tighten the 6 bolts in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket to the oil strainer sub-assembly.


Hide 12102A 45.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12233 50.INSTALL NO. 1 VENTILATION CONNECTOR

Hide 11201 51.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101J 52.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11101J 53.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11301M 55.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11301M 56.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 12108 58.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap.


b.

Install the oil filler cap.