Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM27T0E _51 Engine / Hybrid System _053678 1GR-FE INTAKE / EXHAUST _0260643 EXHAUST MANIFOLD A

1GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17105 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A222094E05
1.521,0.927 1.792,0.927 true 1.792,0.896 1.969,1.177 true 1.292,0.844 1.604,1.083 0.313,0.24 10 true *1

Install a new gasket to the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the manifold with 6 new nuts.


c.

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

U169299E02
4.344,0.667 4.573,0.865 0.229,0.198 10 false 1 5.833,0.656 6.083,0.875 0.25,0.219 10 false 2 6.333,0.958 6.563,1.156 0.229,0.198 10 false 3 5.677,1.979 5.854,2.177 0.177,0.198 10 false 4 4.99,1.979 5.146,2.177 0.156,0.198 10 false 5 4.01,1.885 4.198,2.073 0.188,0.188 10 false 6 0.656,0.667 0.844,0.844 0.188,0.177 10 false 1 2.156,0.688 2.354,0.875 0.198,0.188 10 false 2 2.635,0.979 2.844,1.167 0.208,0.188 10 false 3 1.969,1.969 2.188,2.156 0.219,0.188 10 false 4 1.281,1.99 1.51,2.167 0.229,0.177 10 false 5 0.271,1.896 0.5,2.135 0.229,0.24 10 false 6 0.385,0.135 0.542,0.281 0.156,0.146 10 false *1 4.177,0.146 4.333,0.292 0.156,0.146 10 false *2

Text in Illustration
*1 w/ Secondary Air Injection System *2 w/o Secondary Air Injection System


d.

Connect the air fuel ratio sensor connector.


Hide 17168 3.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17362 4.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17118 5.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 89467B 6.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17104 7.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A222095E05
0.531,1.042 0.688,0.573 true 0.688,0.573 1.042,0.573 true 1.063,0.469 1.344,0.677 0.281,0.208 10 true *1

Install a new gasket to the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the manifold with 6 new nuts.


c.

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

U169298E01
1.766,0.727 1.880,0.875 0.114,0.148 10 1 2.749,0.814 2.864,0.962 0.114,0.148 10 2 2.777,1.892 2.892,2.039 0.114,0.148 10 3 2.301,2.17 2.416,2.318 0.114,0.148 10 4 1.731,2.071 1.845,2.219 0.114,0.148 10 5 1.385,2.126 1.499,2.274 0.114,0.148 10 6 5.845,0.727 5.959,0.875 0.114,0.148 10 1 6.557,0.791 6.671,0.939 0.114,0.148 10 2 6.563,1.9 6.677,2.048 0.114,0.148 10 3 6.102,2.196 6.216,2.344 0.114,0.148 10 4 5.546,2.098 5.660,2.245 0.114,0.148 10 5 5.186,2.153 5.300,2.300 0.114,0.148 10 6 0.176,0.082 0.360,0.236 0.184,0.154 10 *1 4.119,0.098 4.302,0.252 0.184,0.154 10 *2

Text in Illustration
*1 w/ Secondary Air Injection System *2 w/o Secondary Air Injection System


d.

Connect the air fuel ratio sensor connector.


Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 45203 9.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)

a.

for Manual Tilt and Manual Telescopic Steering Column:

Connect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>INSTALLATION).


b.

for Power Tilt and Power Telescopic Steering Column:

Connect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>INSTALLATION).


Hide 17361 10.INSTALL AIR TUBE (w/ Secondary Air Injection System)

Hide 17119 11.INSTALL NO. 2 MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


Hide 53737B 18.INSTALL FRONT FENDER APRON SEAL LH

a.

w/ KDSS:

Install the apron seal with the 7 clips.


b.

w/o KDSS:

Install the apron seal with the 4 clips.


Hide 53736 19.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the apron seal with the 5 clips.


Hide 53737A 20.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

a.

Install the frame seal with the 5 clips.


Hide 53736B 21.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Install the frame seal with the 5 clips.