Home › Engine / Hybrid System › 1KD-FTV (COOLING) › THERMOSTAT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053682 1KD-FTV COOLING _0260665 THERMOSTAT A

1KD-FTV COOLING  THERMOSTAT  INSTALLATION  


PROCEDURE

Hide 16331A 1.INSTALL THERMOSTAT

a.
A385687E01
1.333,3.698 2.313,3.698 true 1.313,3.406 1.49,3.167 true 1.531,1.344 1.531,1.052 false 2.552,1.323 2.552,1.083 false 1.458,1.354 1.771,1.552 0.313,0.198 10 false *1 2.479,1.333 2.792,1.531 0.313,0.198 10 false *1 1.438,0.417 1.75,0.615 0.313,0.198 10 false *a 2.5,0.427 2.813,0.625 0.313,0.198 10 false *b 0.76,3.406 1.01,3.604 0.25,0.198 10 true 30° 1.594,3.406 1.844,3.604 0.25,0.198 10 true 30° 1.458,3.01 1.771,3.208 0.313,0.198 10 false *c 2.333,3.604 2.646,3.802 0.313,0.198 10 false *2

Install a new gasket to the thermostat.

Text in Illustration
*1 Gasket
*2 Jiggle Valve
*a CORRECT
*b INCORRECT
*c Upward

NOTICE:

When installing the gasket to the thermostat, be careful not to deform the gasket. Make sure that the gasket is properly installed to the thermostat as shown in the illustration.



b.

Install the thermostat to the cylinder block with the jiggle valve facing straight upward.

HINT:

The jiggle valve may be set within 30° of either side of the prescribed position.



Hide 16321 2.INSTALL WATER INLET

a.

Install the inlet with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.
A224946E02
0.667,1.594 0.813,1.76 0.146,0.167 10 true A 0.823,1.833 0.958,1.99 0.135,0.156 10 true B

for Automatic Transmission:

Install the hose clamp and bracket with bolt A. Then install the oil pipe clamp with bolt B.

Torque:
for bolt A : 14 N*m (143 kgf*cm, 10 ft.*lbf)
for bolt B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16264D 3.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the water inlet.


Hide 88431 7.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 88320 10.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 87101 11.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 87120G 12.INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)

Hide 17801 16.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 87452A 20.INSTALL FRONT HEATER BRACKET (for Cold Area Specification Vehicles)

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 26.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 28.INSTALL UPPER RADIATOR SUPPORT SEAL