Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  Multi-terrain Select Indicator Light does not Come ON  


DESCRIPTION

When the multi-terrain select switch (center cluster module switch) is operated, multi-terrain select control is enabled and the multi-terrain select indicator light illuminates.

After selecting a road surface type displayed on the multi-information display using the multi-terrain select road mode selector (center cluster module switch), the system optimizes throttle control and brake fluid pressure control for wheels that slip when accelerating, which allows the power lost when wheels slip during acceleration to be distributed to all 4 wheels.

The slip indicator light blinks while the system is operating.

The system can operate under the following conditions:

·

The vehicle stability control system is normal.

·

The system is not in VSC OFF mode or TRC OFF mode.

·

Crawl control is not operating.

·

Shift position not P or N.

·

The transfer is set to L4.


When there is a malfunction in the multi-terrain select system, a message is displayed on the multi-information display.

A mode screen display signal is sent to the combination meter assembly via LIN communication from the driving support switch control ECU to display the multi-terrain select road mode on the multi-information display.

WIRING DIAGRAM

C294631E04
2.052,3.292 3.427,3.688 1.375,0.396 10 false Driving Support Switch Control ECU 2.458,5.469 2.844,5.75 0.385,0.281 10 false A7 2.448,5.646 5.823,6.042 3.375,0.396 10 false Skid Control ECU (Master Cylinder Solenoid) 0.25,2.635 1.49,2.948 1.24,0.313 10 false Multi-terrain Select 0.073,3.573 0.479,3.844 0.406,0.271 10 false G6 0.115,3.75 1.281,4.125 1.167,0.375 10 false Combination Meter Assembly 0.688,5.927 2.646,6.198 1.958,0.271 10 false : CAN Communication System 4.104,3.698 4.667,3.969 0.563,0.271 10 false G156 4.365,3.01 5.875,3.375 1.51,0.365 10 false Multi-terrain Select Road Mode Selector 3.958,0.802 4.313,1.083 0.354,0.281 10 false 20 4.219,1.906 4.625,2.198 0.406,0.292 10 false ECU 4.302,1.115 6,1.365 1.698,0.25 10 false Multi-terrain Select Switch 6.219,0.781 6.5,1.052 0.281,0.271 10 false E 6.396,0.792 6.708,1.042 0.313,0.25 10 false 24 4.219,2.156 4.594,2.438 0.375,0.281 10 false UP 3.958,1.917 4.26,2.177 0.302,0.26 10 false 17 4.219,2.406 4.583,2.635 0.365,0.229 10 false DN 3.948,2.406 4.271,2.667 0.323,0.26 10 false 19 2.875,0.896 3.344,1.146 0.469,0.25 10 false MTS 3.271,0.802 3.635,1.083 0.365,0.281 10 false 8 2.802,2.51 3.333,2.802 0.531,0.292 10 false MOD3 3.281,1.896 3.573,2.125 0.292,0.229 10 false 4 2.802,2.26 3.344,2.563 0.542,0.302 10 false MOD2 3.281,2.156 3.583,2.406 0.302,0.25 10 false 2 2.052,3.125 2.51,3.396 0.458,0.271 10 false G162 2.813,2 3.292,2.198 0.479,0.198 10 false MOD1 3.26,2.406 3.594,2.667 0.333,0.26 10 false 11 3.948,2.156 4.271,2.396 0.323,0.24 10 false 18 4.594,1.771 4.917,2.031 0.323,0.26 10 false 1 4.833,1.771 5.177,2.042 0.344,0.271 10 false 2 5.094,1.771 5.458,2.052 0.365,0.281 10 false 3 5.344,1.771 5.667,2.021 0.323,0.25 10 false 4 5.604,1.771 5.917,2.01 0.313,0.24 10 false 5 4.229,0.802 4.729,1.083 0.5,0.281 10 false FRE 4.104,3.885 6.344,4.208 2.24,0.323 10 false Center Cluster Module Switch 0.729,6.365 2.583,6.604 1.854,0.24 10 false : LIN Communication System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

2.CHECK LIN COMMUNICATION LINE
a.

Use the GTS to check if the LIN communication system is functioning normally.

Result
Result Proceed to
LIN DTC is not output A
LIN DTC is output B



A

3.CHECK DTC

B

GO TO LIN COMMUNICATION SYSTEM (HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS)

3.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

4.READ VALUE USING GTS (OFF-ROAD GUIDANCE SWITCH AND DIAL SWITCH SIGNAL)

B

4.READ VALUE USING GTS (OFF-ROAD GUIDANCE SWITCH AND DIAL SWITCH SIGNAL)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / D-SEAT SW / Data List.


f.

Check the Data List for proper functioning of the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch).

D-SEAT SW
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Off-road Guidance Switch Multi-terrain select switch/ ON or OFF ON: Switch on
OFF: Switch off
-
Dial Switch Signal 1 Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF Switches between ON and OFF according to the ON/OFF Combination Chart (See page (Click here)) -
Dial Switch Signal 2 Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF -
Dial Switch Signal 3 Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF -

OK:

The GTS display changes according to multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) operation.




OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
5.INSPECT COMBINATION METER ASSEMBLY
a.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The multi-terrain select indicator light turns on or off in accordance with the Active Test operation.


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

6.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
a.

Disconnect the G156 center cluster module switch connector.


b.

Disconnect the G162 driving support switch control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G162-8 (MTS) - G156-20 (FRE) Always Below 1 Ω
G162-4 (MOD1) - G156-17 (ECU) Always Below 1 Ω
G162-11 (MOD3) - G156-19 (DN) Always Below 1 Ω
G162-2 (MOD2) - G156-18 (UP) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G162-8 (MTS) or G156-20 (FRE) - Body ground Always 10 kΩ or higher
G162-4 (MOD1) or G156-17 (ECU) - Body ground Always 10 kΩ or higher
G162-11 (MOD3) or G156-19 (DN) - Body ground Always 10 kΩ or higher
G162-2 (MOD2) or G156-18 (UP) - Body ground Always 10 kΩ or higher




OK

7.INSPECT CENTER CLUSTER MODULE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT CENTER CLUSTER MODULE SWITCH
a.

Remove the center cluster module switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>MULTI-TERRAIN SELECT SWITCH>REMOVAL).


b.

Inspect the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>MULTI-TERRAIN SELECT SWITCH>INSPECTION).



OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG