Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U1002  Lost Communication with Gateway Module (Power Management1)  


DESCRIPTION

·

The power management control ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the V2 bus.

·

When the power management control ECU receives a response signal from the ECUs connected to the V2 bus, the power management control ECU recognizes and memorizes that the ECU is connected to the V2 bus. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to the V2 bus when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to the V2 bus, the power management control ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module (Power Management1).
·

V2 bus circuit

·

Parking assist ECU CAN branch wire or connector*1

·

Clearance warning ECU assembly CAN branch wire or connector*2

·

Driving support ECU assembly CAN branch wire or connector*3

·

Stabilizer control ECU CAN branch wire or connector*4

·

Seat belt control ECU CAN branch wire or connector*3

·

Blind spot monitor sensor LH CAN branch wire or connector*5

·

Suspension control ECU CAN branch wire or connector*6

·

Headlight swivel ECU assembly CAN branch wire or connector*7

·

Power management control ECU CAN main wire or connector

·

Parking assist ECU*1

·

Clearance warning ECU assembly*2

·

Driving support ECU assembly*3

·

Stabilizer control ECU*4

·

Seat belt control ECU*3

·

Blind spot monitor sensor LH*5

·

Suspension control ECU*6

·

Headlight swivel ECU assembly*7

·

Air conditioning amplifier assembly*8

·

Power management control ECU

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

No. 4 junction connector

·

No. 6 junction connector*5



*1: w/ Side Monitor System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Pre-crash Safety System

*4: w/ Kinetic Dynamic Suspension System

*5: w/ Blind Spot Monitor System

*6: w/ Air Suspension System

*7: for LED Headlight

*8: for 1GR-FE, 1GD-FTV


WIRING DIAGRAM

C329308E01
4.007,0.54 4.105,0.677 0.098,0.137 10 2 4.007,0.993 4.182,1.130 0.175,0.137 10 13 3.232,0.54 3.328,0.677 0.096,0.137 10 3 3.156,0.993 3.327,1.130 0.172,0.137 10 14 3.23,4.915 3.328,5.052 0.098,0.137 10 1 3.152,5.368 3.327,5.505 0.175,0.137 10 12 1.95,5.142 2.125,5.279 0.175,0.137 10 *5 1.95,5.588 2.125,5.725 0.175,0.137 10 *5 2.735,4.932 2.910,5.069 0.175,0.137 10 *4 2.735,5.378 2.910,5.514 0.175,0.137 10 *4 1.349,0.54 1.607,0.679 0.258,0.139 10 7 1.349,0.993 1.551,1.132 0.203,0.139 10 8 0.792,0.639 1.211,0.776 0.419,0.137 10 CANH 0.819,1.083 1.212,1.220 0.393,0.137 10 CANL 5.012,0.54 5.843,0.679 0.831,0.139 10 26*10, 12*11 5.019,0.993 5.844,1.132 0.824,0.139 10 25*10, 11*11 1.349,2.909 1.607,3.048 0.258,0.139 10 3 1.013,3.008 1.213,3.145 0.200,0.137 10 R1 1.015,3.452 1.213,3.589 0.198,0.137 10 R2 0.299,3.811 1.165,3.974 0.867,0.163 10 G154 0.299,3.951 1.524,4.316 1.226,0.364 10 Clearance Warning ECU Assembly*3 1.349,3.362 1.551,3.501 0.203,0.139 10 5 5.945,0.52 6.623,0.656 0.678,0.137 10 CA3P*11 5.945,0.324 6.632,0.460 0.688,0.137 10 CA2H*10 5.971,1.214 6.676,1.351 0.704,0.137 10 CA2L*10 5.971,1.397 6.635,1.533 0.663,0.137 10 CA3N*11 5.495,1.573 5.936,1.710 0.441,0.137 10 G51 5.495,1.72 6.766,2.084 1.271,0.364 10 Power Management Control ECU 4.007,2.909 4.105,3.046 0.098,0.137 10 4 4.007,3.362 4.182,3.499 0.175,0.137 10 15 4.007,4.898 4.105,5.035 0.098,0.137 10 6 4.007,5.352 4.182,5.489 0.175,0.137 10 17 3.232,2.909 3.328,3.046 0.096,0.137 10 5 3.156,3.362 3.327,3.499 0.172,0.137 10 16 5.678,2.909 5.849,3.048 0.172,0.139 10 39 5.678,3.362 5.849,3.501 0.172,0.139 10 17 5.971,3.008 6.457,3.145 0.485,0.137 10 CA2H 5.971,3.452 6.450,3.589 0.479,0.137 10 CA2L 5.635,3.825 6.076,3.962 0.441,0.137 10 G119 5.635,3.972 6.969,4.337 1.334,0.364 10 Driving Support ECU Assembly*2 3.04,5.815 3.507,5.978 0.467,0.163 10 G98 3.04,5.997 4.650,6.361 1.610,0.364 10 No. 3 Junction Connector 0.049,7.001 2.552,7.140 2.503,0.139 10 *1: w/ Air Suspension System 0.049,7.716 4.149,7.855 4.101,0.139 10 *3: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type) 0.049,7.358 2.552,7.498 2.503,0.139 10 *2: w/ Pre-crash Safety System 0.049,8.074 2.552,8.213 2.503,0.139 10 *4: w/ Blind Spot Monitor System 0.049,8.431 2.552,8.571 2.503,0.139 10 *5: w/o Blind Spot Monitor System 0.299,1.445 0.740,1.582 0.441,0.137 10 A49 0.299,1.592 1.570,1.957 1.271,0.364 10 Suspension Control ECU*1 5.473,5.654 5.779,5.817 0.307,0.163 10 G25 5.473,5.85 7.094,6.214 1.621,0.364 10 Air Conditioning Amplifier Assembly*11 5.94,5.002 6.407,5.165 0.467,0.163 10 CANH 5.94,5.444 6.407,5.606 0.467,0.163 10 CANL 5.677,4.895 5.852,5.032 0.175,0.137 10 11 5.668,5.358 5.854,5.495 0.186,0.137 10 12 2.58,8.431 5.083,8.571 2.503,0.139 10 *11: for 1GR-FE, 1GD-FTV 2.58,8.074 5.083,8.213 2.503,0.139 10 *10: for 1KD-FTV

C329309E02
3.236,2.669 3.332,2.806 0.096,0.137 10 1 3.16,3.122 3.331,3.259 0.172,0.137 10 12 3.983,2.669 4.081,2.806 0.098,0.137 10 2 3.983,3.122 4.158,3.259 0.175,0.137 10 13 5.728,2.669 5.826,2.808 0.097,0.139 10 3 5.728,3.122 5.826,3.261 0.097,0.139 10 5 5.947,2.769 6.367,2.905 0.419,0.137 10 R1 5.947,3.218 6.389,3.355 0.441,0.137 10 R2 5.555,3.562 5.996,3.699 0.441,0.137 10 I1 5.555,3.709 7.116,4.073 1.561,0.364 10 Clearance Warning ECU Assembly*6 3.236,6.286 3.332,6.423 0.096,0.137 10 3 3.16,6.739 3.331,6.876 0.172,0.137 10 14 3.016,7.054 3.483,7.217 0.467,0.163 10 G95 3.016,7.208 4.612,7.573 1.596,0.364 10 No. 2 Junction Connector 1.852,2.605 2.027,2.742 0.175,0.137 10 *5 1.442,2.605 1.617,2.742 0.175,0.137 10 *5 2.287,2.605 2.462,2.742 0.175,0.137 10 *4 2.668,2.605 2.843,2.742 0.175,0.137 10 *4 2.287,0.363 2.462,0.500 0.175,0.137 10 *4 2.668,0.363 2.843,0.500 0.175,0.137 10 *4 2.737,7.889 6.939,8.060 4.202,0.171 10 *6: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type) 2.739,8.178 4.670,8.317 1.931,0.139 10 *7: w/ Side Monitor System 0.089,8.178 2.593,8.317 2.503,0.139 10 *4: w/ Blind Spot Monitor System 0.089,8.492 2.593,8.631 2.503,0.139 10 *5: w/o Blind Spot Monitor System 4.007,4.469 4.105,4.606 0.098,0.137 10 4 4.007,4.923 4.182,5.059 0.175,0.137 10 15 3.232,4.469 3.328,4.606 0.096,0.137 10 5 3.156,4.923 3.327,5.059 0.172,0.137 10 16 5.678,4.469 5.849,4.608 0.172,0.139 10 40 5.678,4.923 5.849,5.061 0.172,0.139 10 39 5.971,4.568 6.457,4.705 0.485,0.137 10 CANH 5.971,5.013 6.450,5.149 0.479,0.137 10 CANL 5.635,5.385 6.076,5.522 0.441,0.137 10 I7 5.635,5.532 7.031,5.897 1.396,0.364 10 Parking Assist ECU*7 1.348,4.469 1.607,4.608 0.258,0.139 10 29 0.793,4.568 1.211,4.705 0.418,0.137 10 CANH 0.814,5.013 1.212,5.149 0.397,0.137 10 CANL 0.299,5.371 1.165,5.534 0.867,0.163 10 G123 0.299,5.511 1.851,5.876 1.552,0.364 10 Stabilizer Control ECU*8 1.348,4.923 1.551,5.061 0.203,0.139 10 28 2.739,8.492 5.686,8.648 2.948,0.156 10 *8: w/ Kinetic Dynamic Suspension System 5.748,6.277 5.850,6.416 0.102,0.139 10 1 5.748,6.731 5.850,6.870 0.102,0.139 10 2 5.971,6.377 6.457,6.513 0.485,0.137 10 CANH 5.971,6.821 6.450,6.957 0.479,0.137 10 CANL 5.495,7.194 5.936,7.330 0.441,0.137 10 G118 5.492,7.356 7.069,7.720 1.577,0.364 10 Seat Belt Control ECU*2 0.089,7.889 2.593,8.028 2.503,0.139 10 *2: w/ Pre-crash Safety System 2.875,1.97 3.342,2.133 0.467,0.163 10 R47 2.875,2.124 4.680,2.489 1.804,0.364 10 No. 6 Junction Connector*4 3.207,0.356 3.304,0.493 0.096,0.137 10 3 3.131,0.809 3.303,0.946 0.172,0.137 10 14 3.983,0.356 4.081,0.493 0.098,0.137 10 2 3.983,0.809 4.158,0.946 0.175,0.137 10 13 5.728,0.356 5.826,0.495 0.097,0.139 10 2 5.728,0.809 5.826,0.948 0.097,0.139 10 7 5.947,0.456 6.366,0.592 0.419,0.137 10 CA1P 5.947,0.905 6.388,1.042 0.441,0.137 10 CA1N 5.611,1.249 6.052,1.386 0.441,0.137 10 R42 5.625,1.424 6.896,1.788 1.271,0.364 10 Blind Spot Monitor Sensor LH*4 3.207,1.258 3.304,1.394 0.096,0.137 10 1 3.131,1.711 3.303,1.848 0.172,0.137 10 12

C329310E01
0.304,4.168 2.807,4.307 2.503,0.139 10 *9: for LED Headlight 2.257,0.79 2.354,0.927 0.096,0.137 10 2 2.182,1.23 2.353,1.381 0.172,0.151 10 13 4.663,0.79 4.847,0.929 0.184,0.139 10 12 4.663,1.244 4.842,1.383 0.180,0.139 10 13 4.969,0.879 5.388,1.016 0.419,0.137 10 CANH 4.969,1.323 5.362,1.460 0.393,0.137 10 CANL 4.683,1.659 5.150,1.821 0.467,0.163 10 A58 4.683,1.813 6.099,2.148 1.415,0.335 10 Headlight Swivel ECU Assembly*9 3.005,2.592 3.103,2.728 0.098,0.137 10 1 3.005,3.045 3.180,3.182 0.175,0.137 10 12 3.005,0.79 3.101,0.927 0.096,0.137 10 3 3.005,1.244 3.176,1.381 0.172,0.137 10 14 4.741,2.592 4.848,2.730 0.107,0.139 10 3 4.741,3.045 4.848,3.184 0.107,0.139 10 2 4.969,2.592 5.454,2.728 0.485,0.137 10 CANH 4.969,3.233 5.448,3.370 0.479,0.137 10 CANL 4.535,3.508 4.976,3.645 0.441,0.137 10 G102 4.535,3.655 6.128,4.019 1.593,0.364 10 No. 4 Junction Connector 1.898,3.364 2.364,3.526 0.467,0.163 10 A72 1.898,3.522 3.508,3.886 1.610,0.364 10 No. 1 Junction Connector

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
a.
U169939E02
2.01,1.198 1.854,1.833 1.854,1.833 1.667,1.833 true 1.635,0.99 1.448,0.542 1.448,0.542 1.354,0.542 true 1.948,1.188 2.365,0.417 2.365,0.417 2.5,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.104 2.365,1.781 2.365,1.781 2.51,1.781 true 2.208,1.104 2.542,1.583 2.542,1.583 2.667,1.583 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.094 3.302,1.26 0.396,0.167 10 false AM22 1.021,0.469 1.365,0.635 0.344,0.167 10 false GND 1.156,1.75 1.698,1.927 0.542,0.177 10 false CA2L*A 2.531,0.344 3.146,0.521 0.615,0.177 10 false CA2H*A 2.552,1.708 3.094,1.885 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Component with harness connector
(Power Management Control ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

B

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

C

73.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U148799E03
2.646,0.604 2.583,0.604 2.583,0.604 2.219,1.083 true 2.635,1.75 2.573,1.75 2.573,1.75 2.208,1.271 true 2.688,0.542 3.125,0.719 0.438,0.177 10 false CANH 0.281,0.927 0.604,1.104 0.323,0.177 10 false G98 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 2.688,1.667 3.125,1.844 0.438,0.177 10 false CANL

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-2 (CANH) - G98-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U148800E02
2.667,0.938 2.604,0.938 2.604,0.938 2.323,1.094 true 2.677,1.417 2.615,1.417 2.615,1.417 2.333,1.25 true 2.698,0.854 3.135,1.031 0.438,0.177 10 false CANH 0.292,0.917 0.615,1.094 0.323,0.177 10 false G98 0.094,0.031 0.302,0.208 0.208,0.177 10 false *a 2.719,1.333 3.156,1.51 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (w/ Blind Spot Monitor System) B
NG (w/o Blind Spot Monitor System) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

7.CONNECT CONNECTOR

C

13.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)
a.
U169935E02
1.781,1.448 1.635,1.979 1.635,1.979 1.5,1.979 true 1.708,1.438 1.313,1.76 1.313,1.76 1.219,1.76 true 1.969,1.292 2.406,0.615 2.406,0.615 2.542,0.615 true 2.052,1.292 2.604,0.906 2.604,0.906 2.688,0.906 true 0.01,0.01 0.25,0.198 0.24,0.188 10 true *a 0.948,1.896 1.573,2.052 0.625,0.156 10 false CA2L*A 0.656,1.667 1.292,1.823 0.635,0.156 10 false CA2H*A 0.552,1.188 0.885,1.344 0.333,0.156 10 false G51 2.719,0.833 3.26,0.99 0.542,0.156 10 false CA3N*B 2.573,0.531 3.208,0.688 0.635,0.156 10 false CA3P*B

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-25 (CA3N) Engine switch off 108 to 132 Ω


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U148802E01
2.7,0.785 3.134,0.925 0.434,0.140 10 CANH 0.34,1.151 0.615,1.290 0.275,0.139 10 R47 0.053,0.086 0.266,0.264 0.213,0.178 10 *a 2.672,1.506 3.105,1.647 0.434,0.140 10 CANL 2.673,0.859 2.558,0.859 2.558,0.859 2.324,1.095 false 2.644,1.594 2.53,1.594 2.53,1.594 2.336,1.338 false

Disconnect the R47 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-1 (CANH) - R47-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

NG

10.CONNECT CONNECTOR
9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148803E01
0.34,1.151 0.615,1.290 0.275,0.139 10 R47 2.7,0.573 3.134,0.713 0.434,0.140 10 CANH 0.053,0.086 0.266,0.264 0.213,0.178 10 *a 2.7,1.695 3.134,1.836 0.434,0.140 10 CANL 2.673,0.647 2.558,0.647 2.558,0.647 2.089,1.095 false 2.673,1.783 2.558,1.783 2.558,1.783 2.1,1.338 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-3 (CANH) - R47-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the R47 No. 6 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U148798E03
2.104,1.083 2.458,0.667 2.458,0.667 2.552,0.667 true 2.104,1.302 2.563,1.667 2.563,1.667 2.656,1.667 true 2.583,0.583 3.021,0.76 0.438,0.177 10 false CANH 2.688,1.583 3.125,1.76 0.438,0.177 10 false CANL 0.323,0.875 0.646,1.052 0.323,0.177 10 false G95 0.104,0.042 0.313,0.219 0.208,0.177 10 false *a

Disconnect the G95 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

NG

16.CONNECT CONNECTOR
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U148797E03
2.677,0.927 2.615,0.927 2.615,0.927 2.333,1.094 true 2.688,1.448 2.625,1.448 2.625,1.448 2.344,1.292 true 2.719,0.875 3.156,1.052 0.438,0.177 10 false CANH 0.385,1.052 0.708,1.229 0.323,0.177 10 false G95 0.094,0 0.302,0.177 0.208,0.177 10 false *a 2.719,1.385 3.156,1.563 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-1 (CANH) - G95-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

13.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U148798E04
2.104,1.083 2.458,0.667 2.458,0.667 2.552,0.667 true 2.104,1.302 2.563,1.667 2.563,1.667 2.656,1.667 true 2.583,0.583 3.021,0.76 0.438,0.177 10 false CANH 2.688,1.583 3.125,1.76 0.438,0.177 10 false CANL 0.354,0.917 0.677,1.094 0.323,0.177 10 false G95 0.104,0.042 0.313,0.219 0.208,0.177 10 false *a

Disconnect the G95 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

NG

16.CONNECT CONNECTOR
15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148797E04
2.667,0.917 2.604,0.917 2.604,0.917 2.323,1.083 true 2.677,1.469 2.615,1.469 2.615,1.469 2.333,1.313 true 2.698,0.844 3.135,1.021 0.438,0.177 10 false CANH 0.385,1.052 0.708,1.229 0.323,0.177 10 false G95 0.094,0 0.302,0.177 0.208,0.177 10 false *a 2.719,1.385 3.156,1.563 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-1 (CANH) - G95-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

16.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U170252E02
2.677,0.917 2.615,0.917 2.615,0.917 2.333,1.083 true 2.677,1.458 2.615,1.458 2.615,1.458 2.333,1.302 true 2.708,0.844 3.146,1.021 0.438,0.177 10 false CANH 0.396,1.052 0.719,1.229 0.323,0.177 10 false A72 0.094,0 0.302,0.177 0.208,0.177 10 false *a 2.719,1.385 3.156,1.563 0.438,0.177 10 false CANL

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-1 (CANH) - A72-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

19.CONNECT CONNECTOR
18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170253E02
2.646,0.615 2.583,0.615 2.583,0.615 2.219,1.094 true 2.656,1.802 2.594,1.802 2.594,1.802 2.219,1.313 true 2.688,0.542 3.125,0.719 0.438,0.177 10 false CANH 0.365,1.188 0.688,1.365 0.323,0.177 10 false A72 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 2.688,1.729 3.125,1.906 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-2 (CANH) - A72-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

19.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U148311E01
2.258,0.121 2.691,0.299 0.434,0.178 10 CANH 0.441,0.839 0.800,1.017 0.360,0.178 10 G102 0.104,0.011 0.317,0.189 0.213,0.178 10 *a 2.533,1.46 2.967,1.638 0.434,0.178 10 CANL 2.248,0.195 2.185,0.195 2.185,0.195 1.409,0.826 false 2.523,1.548 2.46,1.548 2.46,1.548 1.779,1.029 false

Disconnect the G102 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
U169939E03
2.01,1.198 1.75,1.833 1.75,1.833 1.573,1.833 true 1.646,0.979 1.458,0.531 1.458,0.531 1.365,0.531 true 1.948,1.188 2.365,0.417 2.365,0.417 2.5,0.417 true 2.521,1.01 2.833,1.156 2.833,1.156 2.865,1.156 true 2.146,1.104 2.365,1.781 2.365,1.781 2.51,1.781 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.083 2.208,0.25 0.292,0.167 10 false G51 2.906,1.094 3.302,1.26 0.396,0.167 10 false AM22 1.052,0.448 1.396,0.615 0.344,0.167 10 false GND 1.073,1.75 1.615,1.927 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.708 3.083,1.885 0.542,0.177 10 false CA3P*B 2.698,1.521 3.313,1.698 0.615,0.177 10 false CA3N*B

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Component with harness connector
(Power Management Control ECU)



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NG

28.CONNECT CONNECTOR
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)
NOTICE:

For vehicles with a halogen headlight, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - No. 4 Junction Connector)".


a.
U170398E02
2.094,1.156 2.469,0.76 2.469,0.76 2.688,0.76 true 2.083,1.375 2.469,1.802 2.469,1.802 2.604,1.802 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.615,2.5 1.5,2.177 1.5,2.177 1.385,2.177 true 0.385,0.979 0.646,1.156 0.26,0.177 10 false A72 2.729,0.677 3.135,0.854 0.406,0.177 10 false CANH 2.635,1.719 3.021,1.896 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.135,2.083 1.365,2.26 0.229,0.177 10 false CG 0.396,2.667 0.677,2.844 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-3 (CANH) - A72-14 (CANL) Engine switch off 200 Ω or higher
A72-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A72-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A72-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A72-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)

NG

24.CONNECT CONNECTOR
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
a.
U170399E02
2.313,1.146 2.469,0.969 2.469,0.969 2.688,0.969 true 2.323,1.375 2.531,1.677 2.531,1.677 2.667,1.677 true 2.208,2.969 2.292,3.177 2.292,3.177 2.417,3.177 true 1.635,2.51 1.521,2.188 1.521,2.188 1.406,2.188 true 0.385,0.927 0.646,1.104 0.26,0.177 10 false A72 2.729,0.896 3.135,1.073 0.406,0.177 10 false CANH 2.688,1.594 3.073,1.771 0.385,0.177 10 false CANL 2.458,3.104 2.75,3.281 0.292,0.177 10 false BAT 1.146,2.094 1.375,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-1 (CANH) - A72-12 (CANL) Engine switch off 108 to 132 Ω
A72-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A72-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A72-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A72-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

26.CONNECT CONNECTOR
24.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

25.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
25.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
a.
U148723E03
2.51,1.677 2.615,1.677 2.615,1.677 2.792,0.969 true 2.885,0.333 2.771,0.333 2.771,0.333 2.677,0.885 true 1.646,2.51 1.49,2.208 1.49,2.208 1.406,2.208 true 2.219,2.938 2.427,3.104 2.427,3.104 2.51,3.104 true 1.552,0.198 1.833,0.396 0.281,0.198 10 false A58 2.917,0.25 3.333,0.438 0.417,0.188 10 false CANH 2.135,1.604 2.604,1.76 0.469,0.156 10 false CANL 0.427,2.646 0.75,2.823 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.146,2.125 1.385,2.302 0.24,0.177 10 false CG 2.552,3.031 2.99,3.208 0.438,0.177 10 false BAT

Disconnect the A58 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) Engine switch off 54 to 69 Ω
A58-12 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A58-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A58-12 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A58-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)
*b Front view of DLC3



OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (CANH, CANL)

26.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR)
27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR)
a.
U148314E01
0.056,1.611 0.254,1.767 0.198,0.156 10 *b 0.056,0.047 0.254,0.203 0.198,0.156 10 *a 0.323,2.668 0.629,2.824 0.306,0.156 10 G48 0.285,0.606 0.647,0.762 0.362,0.156 10 G102 0.572,0.099 1.017,0.255 0.445,0.156 10 CANH 2.234,1.379 2.680,1.535 0.445,0.156 10 CANL 1.102,0.176 1.225,0.176 1.225,0.176 1.37,0.597 false 2.182,1.474 2.059,1.474 2.059,1.474 1.759,0.786 false 1.087,1.99 1.338,2.145 0.251,0.156 10 CG 2.655,2.926 3.101,3.082 0.445,0.156 10 BAT 1.377,2.067 1.5,2.067 1.5,2.067 1.645,2.488 false 2.603,3.021 2.48,3.021 2.48,3.021 2.305,2.92 false

Disconnect the G102 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Engine switch off 108 to 132 Ω
G102-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G102-2 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G102-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G102-2 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

28.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U149016E03
2.083,1.135 2.458,0.344 2.458,0.344 2.677,0.344 true 2.073,1.354 2.458,1.781 2.458,1.781 2.594,1.781 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.625,2.51 1.51,2.188 1.51,2.188 1.396,2.188 true 0.406,0.979 0.688,1.156 0.281,0.177 10 false G95 2.719,0.26 3.125,0.438 0.406,0.177 10 false CANH 2.625,1.708 3.01,1.885 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.146,2.094 1.375,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G95 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω
G95-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
a.
U169939E04
2.01,1.198 1.833,1.917 1.833,1.917 1.667,1.917 true 1.667,1 1.479,0.552 1.479,0.552 1.385,0.552 true 1.958,1.198 2.375,0.427 2.375,0.427 2.51,0.427 true 2.531,1.01 2.844,1.156 2.844,1.156 2.875,1.156 true 2.156,1.125 2.375,1.802 2.375,1.802 2.521,1.802 true 2.219,1.115 2.552,1.594 2.552,1.594 2.677,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.083 2.208,0.25 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.042,0.469 1.385,0.635 0.344,0.167 10 false GND 1.135,1.833 1.677,2.01 0.542,0.177 10 false CA2L*A 2.531,0.354 3.146,0.531 0.615,0.177 10 false CA2H*A 2.542,1.729 3.083,1.906 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Component with harness connector
(Power Management Control ECU)

Result
Result Proceed to
OK A
NG (w/ Blind Spot Monitor System) B
NG (w/o Blind Spot Monitor System) C



A

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

B

43.CONNECT CONNECTOR

C

56.CONNECT CONNECTOR
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system (for 4 sensor type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Parking Assist ECU)".


a.
U170400E02
2.208,1.146 2.552,0.865 2.552,0.865 2.771,0.865 true 2.198,1.375 2.563,1.75 2.563,1.75 2.698,1.75 true 2.198,2.938 2.281,3.146 2.281,3.146 2.406,3.146 true 1.635,2.5 1.521,2.177 1.521,2.177 1.406,2.177 true 0.396,0.958 0.677,1.135 0.281,0.177 10 false G95 2.813,0.792 3.219,0.969 0.406,0.177 10 false CANH 2.729,1.688 3.115,1.865 0.385,0.177 10 false CANL 2.458,3.073 2.75,3.25 0.292,0.177 10 false BAT 1.146,2.094 1.375,2.271 0.229,0.177 10 false CG 0.385,2.646 0.667,2.823 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-2 (CANH) - G95-13 (CANL) Engine switch off 200 Ω or higher
G95-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - PARKING ASSIST ECU)

NG

35.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - PARKING ASSIST ECU)
NOTICE:

For vehicles without a side monitor system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Stabilizer Control ECU)".


a.
U170401E02
1.979,1.135 2.396,0.521 2.396,0.521 2.615,0.521 true 1.979,1.354 2.365,1.781 2.365,1.781 2.5,1.781 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.635,2.5 1.521,2.177 1.521,2.177 1.406,2.177 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G95 2.656,0.448 3.063,0.625 0.406,0.177 10 false CANH 2.531,1.688 2.917,1.865 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.146,2.083 1.375,2.26 0.229,0.177 10 false CG 0.396,2.667 0.677,2.844 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-4 (CANH) - G95-15 (CANL) Engine switch off 200 Ω or higher
G95-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

NG

37.CONNECT CONNECTOR
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)
NOTICE:

For vehicles without a kinetic dynamic suspension system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Seat Belt Control ECU)".


a.
U149017E03
1.865,1.146 2.458,0.688 2.458,0.688 2.677,0.688 true 1.875,1.375 2.26,1.917 2.26,1.917 2.396,1.917 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.635,2.51 1.521,2.188 1.521,2.188 1.406,2.188 true 0.396,0.99 0.677,1.167 0.281,0.177 10 false G95 2.719,0.604 3.125,0.781 0.406,0.177 10 false CANH 2.417,1.833 2.802,2.01 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.156,2.094 1.385,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-5 (CANH) - G95-16 (CANL) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NG

39.CONNECT CONNECTOR
34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)
NOTICE:

For vehicles without a pre-crash safety system, replace No. 2 junction connector.


a.
U170402E02
1.74,1.125 2.323,0.635 2.323,0.635 2.542,0.635 true 1.729,1.365 2.177,1.969 2.177,1.969 2.313,1.969 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.625,2.521 1.51,2.198 1.51,2.198 1.396,2.198 true 0.396,0.958 0.677,1.135 0.281,0.177 10 false G95 2.604,0.563 3.01,0.74 0.406,0.177 10 false CANH 2.375,1.885 2.76,2.063 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.156,2.104 1.385,2.281 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-6 (CANH) - G95-17 (CANL) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

41.CONNECT CONNECTOR
35.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U170321E01
1.185,1.047 0.88,0.749 0.88,0.749 0.729,0.749 false 0.483,0.667 0.681,0.804 0.198,0.137 10 R1 0.726,0.362 0.923,0.498 0.196,0.137 10 R2 0.064,0.068 0.506,0.205 0.442,0.137 10 *a 1.738,0.343 1.876,0.479 0.138,0.137 10 I1 0.064,1.878 0.506,2.015 0.442,0.137 10 *b 0.422,2.566 0.704,2.702 0.281,0.137 10 G48 2.213,2.858 2.377,3.15 2.377,3.15 2.531,3.15 false 2.554,3.071 2.942,3.208 0.389,0.137 10 BAT 0.987,2 1.376,2.136 0.389,0.137 10 CG 1.669,2.448 1.46,2.074 1.46,2.074 1.305,2.074 false 1.408,1.047 1.119,0.447 1.119,0.447 0.969,0.447 false

Disconnect the I1 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) Engine switch off 54 to 69 Ω
I1-3 (R1) - G48-4 (CG) Engine switch off 200 Ω or higher
I1-5 (R2) - G48-4 (CG) Engine switch off 200 Ω or higher
I1-3 (R1) - G48-16 (BAT) Engine switch off 6 kΩ or higher
I1-5 (R2) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)

37.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

38.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
38.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
a.
U148726E01
0.503,1.542 0.930,1.685 0.427,0.142 10 CANL 0.197,1.274 0.614,1.413 0.418,0.140 10 CANH 0.715,1.35 0.877,1.35 0.877,1.35 1.008,1.144 false 0.986,1.629 1.173,1.629 1.173,1.629 1.075,1.144 false 1.721,0.193 1.862,0.337 0.141,0.145 10 I7 0.432,2.651 0.755,2.829 0.324,0.178 10 G48 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 1.136,2.103 1.371,2.281 0.235,0.178 10 CG 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 1.667,2.494 1.513,2.192 1.513,2.192 1.425,2.192 false 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false

Disconnect the I7 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) Engine switch off 54 to 69 Ω
I7-40 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
I7-39 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
I7-40 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
I7-39 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)

39.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

40.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
40.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
a.
U148725E01
0.276,0.844 0.652,1.043 0.376,0.199 10 G123 1.486,0.206 1.904,0.393 0.417,0.188 10 CANH 0.645,1.515 1.116,1.671 0.470,0.156 10 CANL 1.12,1.592 1.227,1.592 1.227,1.592 1.32,1.056 false 1.457,0.281 1.35,0.281 1.35,0.281 1.233,0.986 false 0.432,2.651 0.755,2.829 0.324,0.178 10 G48 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 1.136,2.103 1.371,2.281 0.235,0.178 10 CG 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 1.667,2.494 1.513,2.192 1.513,2.192 1.425,2.192 false 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G123-29 (CANH) - G123- 28 (CANL) Engine switch off 54 to 69 Ω
G123-29 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-28 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-29 (CANH) - G48- 16 (BAT) Engine switch off 6 kΩ or higher
G123-28 (CANL) - G48- 16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)
*b Front view of DLC3



OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)

41.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

42.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
42.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
a.
U170216E02
1.635,2.51 1.479,2.208 1.479,2.208 1.396,2.208 true 2.198,2.927 2.406,3.094 2.406,3.094 2.49,3.094 true 1.917,1.271 2.073,1.042 2.073,1.042 2.156,1.042 true 1.802,1.271 1.99,0.698 1.99,0.698 2.063,0.698 true 0.635,0.865 0.99,1.031 0.354,0.167 10 false G118 0.458,2.677 0.781,2.854 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.146,2.125 1.385,2.302 0.24,0.177 10 false CG 2.531,3.01 2.969,3.188 0.438,0.177 10 false BAT 2.188,0.969 2.74,1.135 0.552,0.167 10 false CANH 2.104,0.635 2.625,0.802 0.521,0.167 10 false CANL

Disconnect the G118 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) Engine switch off 54 to 69 Ω
G118-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-2 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G118-2 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)
*b Front view of DLC3



OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)

43.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170403E02
2.302,1.167 2.563,0.906 2.563,0.906 2.781,0.906 true 2.302,1.365 2.573,1.719 2.573,1.719 2.708,1.719 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.615,2.51 1.5,2.188 1.5,2.188 1.385,2.188 true 0.406,1 0.677,1.177 0.271,0.177 10 false R47 2.833,0.844 3.24,1.021 0.406,0.177 10 false CANH 2.75,1.656 3.135,1.833 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.135,2.104 1.365,2.281 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the R47 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-1 (CANH) - R47-12 (CANL) Engine switch off 108 to 132 Ω
R47-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R47-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)
a.
U169939E05
2.01,1.208 1.583,1.917 1.583,1.917 1.417,1.917 true 1.646,0.99 1.458,0.542 1.458,0.542 1.365,0.542 true 1.948,1.198 2.365,0.427 2.365,0.427 2.5,0.427 true 2.531,1.01 2.844,1.156 2.844,1.156 2.875,1.156 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.219,1.125 2.552,1.604 2.552,1.604 2.677,1.604 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.125 2.208,0.292 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.01,0.469 1.354,0.635 0.344,0.167 10 false GND 0.875,1.833 1.417,2.01 0.542,0.177 10 false CA2L*A 2.531,0.344 3.146,0.521 0.615,0.177 10 false CA2H*A 2.542,1.729 3.083,1.906 0.542,0.177 10 false CA3P*B 2.708,1.521 3.323,1.698 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Component with harness connector
(Power Management Control ECU)



OK

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)

NG

49.CONNECT CONNECTOR
46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)
a.
U149018E03
2.198,1.177 2.469,0.385 2.469,0.385 2.688,0.385 true 2.198,1.365 2.469,1.792 2.469,1.792 2.604,1.792 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.635,2.5 1.521,2.177 1.521,2.177 1.406,2.177 true 0.406,0.969 0.677,1.146 0.271,0.177 10 false R47 2.729,0.292 3.135,0.469 0.406,0.177 10 false CANH 2.625,1.688 3.01,1.865 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.156,2.094 1.385,2.271 0.229,0.177 10 false CG 0.396,2.667 0.677,2.844 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-2 (CANH) - R47-13 (CANL) Engine switch off 200 Ω or higher
R47-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R47-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

47.CONNECT CONNECTOR
47.CONNECT CONNECTOR
a.

Reconnect the R47 No. 6 junction connector.



NEXT

48.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
48.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.
U148920E01
1.571,1.039 1.173,0.656 1.173,0.656 1.022,0.656 false 1.571,1.206 1.173,1.589 1.173,1.589 1.022,1.589 false 0.542,0.585 0.922,0.722 0.380,0.137 10 CA1P 0.531,1.512 0.920,1.649 0.389,0.137 10 CA1N 0.067,0.106 0.509,0.243 0.442,0.137 10 *a 2.632,1.041 2.906,1.178 0.275,0.137 10 R42 0.067,1.985 0.509,2.122 0.442,0.137 10 *b 0.407,2.655 0.691,2.792 0.284,0.137 10 G48 2.216,2.965 2.38,3.239 2.38,3.239 2.535,3.239 false 2.557,3.161 2.945,3.298 0.389,0.137 10 BAT 0.956,2.072 1.344,2.209 0.389,0.137 10 CG 1.638,2.521 1.429,2.147 1.429,2.147 1.274,2.147 false

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) Engine switch off 54 to 69 Ω
R42-2 (CA1P) - G48-4 (CG) Engine switch off 200 Ω or higher
R42-7 (CA1N) - G48-4 (CG) Engine switch off 200 Ω or higher
R42-2 (CA1P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R42-7 (CA1N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

49.CONNECT CONNECTOR
a.

Reconnect the R47 No. 6 junction connector.



NEXT

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U149019E03
2.313,1.167 2.573,0.854 2.573,0.854 2.792,0.854 true 2.292,1.354 2.563,1.781 2.563,1.781 2.698,1.781 true 2.198,2.948 2.281,3.156 2.281,3.156 2.406,3.156 true 1.625,2.51 1.51,2.188 1.51,2.188 1.396,2.188 true 0.385,0.927 0.667,1.104 0.281,0.177 10 false G98 2.833,0.771 3.24,0.948 0.406,0.177 10 false CANH 2.729,1.708 3.115,1.885 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.135,2.104 1.365,2.281 0.229,0.177 10 false CG 0.396,2.667 0.677,2.844 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Engine switch off 108 to 132 Ω
G98-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
NOTICE:

For vehicles without an air suspension system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Driving Support ECU Assembly)".


a.
U149020E01
0.382,0.929 0.666,1.110 0.284,0.181 10 G98 2.613,0.708 3.024,0.890 0.411,0.181 10 CANH 2.615,1.65 3.002,1.831 0.387,0.181 10 CANL 2.457,3.058 2.744,3.239 0.287,0.181 10 BAT 1.137,2.057 1.362,2.239 0.225,0.181 10 CG 0.389,2.641 0.668,2.822 0.280,0.181 10 G48 0.207,1.966 0.363,2.147 0.156,0.181 10 *b 0.159,0.053 0.315,0.234 0.156,0.181 10 *a 2.095,1.081 2.354,0.774 2.354,0.774 2.571,0.774 false 2.088,1.325 2.458,1.755 2.458,1.755 2.592,1.755 false 2.213,2.926 2.295,3.131 2.295,3.131 2.418,3.131 false 1.659,2.468 1.538,2.151 1.538,2.151 1.426,2.151 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-3 (CANH) - G98-14 (CANL) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

NG

63.CONNECT CONNECTOR
52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Clearance Warning ECU Assembly)".


a.
U170404E02
1.979,1.146 2.354,0.729 2.354,0.729 2.563,0.729 true 1.958,1.354 2.365,1.865 2.365,1.865 2.5,1.865 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.635,2.51 1.521,2.188 1.521,2.188 1.406,2.188 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G98 2.604,0.646 3.01,0.823 0.406,0.177 10 false CANH 2.542,1.781 2.927,1.958 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.156,2.094 1.385,2.271 0.229,0.177 10 false CG 0.385,2.646 0.667,2.823 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-4 (CANH) - G98-15 (CANL) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

NG

65.CONNECT CONNECTOR
53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system (for 8 sensor type), go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".


a.
U149021E03
1.854,1.167 2.375,0.708 2.375,0.708 2.583,0.708 true 1.844,1.354 2.323,1.938 2.323,1.938 2.458,1.938 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G98 2.635,0.635 3.042,0.813 0.406,0.177 10 false CANH 2.49,1.854 2.875,2.031 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.167,2.104 1.396,2.281 0.229,0.177 10 false CG 0.385,2.646 0.667,2.823 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-5 (CANH) - G98-16 (CANL) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

67.CONNECT CONNECTOR
54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
NOTICE:

For vehicles with 1KD-FTV, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Power Management Control ECU)".


a.
U170405E02
1.74,1.177 2.385,0.719 2.385,0.719 2.594,0.719 true 1.74,1.354 2.333,1.938 2.333,1.938 2.469,1.938 true 2.198,2.948 2.281,3.156 2.281,3.156 2.406,3.156 true 1.625,2.521 1.51,2.198 1.51,2.198 1.396,2.198 true 0.406,1 0.688,1.177 0.281,0.177 10 false G98 2.635,0.646 3.042,0.823 0.406,0.177 10 false CANH 2.49,1.854 2.875,2.031 0.385,0.177 10 false CANL 2.458,3.073 2.75,3.25 0.292,0.177 10 false BAT 1.156,2.125 1.385,2.302 0.229,0.177 10 false CG 0.385,2.646 0.667,2.823 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-6 (CANH) - G98-17 (CANL) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

69.CONNECT CONNECTOR
55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U149022E03
2.188,1.156 2.438,0.844 2.438,0.844 2.656,0.844 true 2.188,1.375 2.438,1.802 2.438,1.802 2.573,1.802 true 2.198,2.938 2.281,3.146 2.281,3.146 2.406,3.146 true 1.635,2.521 1.521,2.198 1.521,2.198 1.406,2.198 true 0.385,0.927 0.667,1.104 0.281,0.177 10 false G98 2.688,0.792 3.094,0.969 0.406,0.177 10 false CANH 2.604,1.74 2.99,1.917 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.094 1.375,2.271 0.229,0.177 10 false CG 0.406,2.667 0.688,2.844 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-2 (CANH) - G98-13 (CANL) Engine switch off 108 to 132 Ω
G98-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

71.CONNECT CONNECTOR
56.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U149019E04
2.292,1.167 2.552,0.854 2.552,0.854 2.771,0.854 true 2.292,1.365 2.563,1.792 2.563,1.792 2.698,1.792 true 2.208,2.958 2.292,3.167 2.292,3.167 2.417,3.167 true 1.625,2.5 1.51,2.177 1.51,2.177 1.396,2.177 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G98 2.813,0.792 3.219,0.969 0.406,0.177 10 false CANH 2.729,1.719 3.115,1.896 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.146,2.094 1.375,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Engine switch off 108 to 132 Ω
G98-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
NOTICE:

For vehicles without an air suspension system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Driving Support ECU Assembly)".


a.
U149020E03
2.073,1.156 2.333,0.844 2.333,0.844 2.552,0.844 true 2.073,1.375 2.448,1.802 2.448,1.802 2.583,1.802 true 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 true 1.635,2.521 1.521,2.198 1.521,2.198 1.406,2.198 true 0.417,0.979 0.698,1.156 0.281,0.177 10 false G98 2.594,0.771 3,0.948 0.406,0.177 10 false CANH 2.615,1.74 3,1.917 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.156,2.125 1.385,2.302 0.229,0.177 10 false CG 0.406,2.677 0.688,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-3 (CANH) - G98-14 (CANL) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

NG

63.CONNECT CONNECTOR
59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Clearance Warning ECU Assembly)".


a.
U170404E03
1.969,1.156 2.344,0.74 2.344,0.74 2.552,0.74 true 1.969,1.375 2.375,1.885 2.375,1.885 2.51,1.885 true 2.198,2.938 2.281,3.146 2.281,3.146 2.406,3.146 true 1.625,2.51 1.51,2.188 1.51,2.188 1.396,2.188 true 0.417,0.969 0.698,1.146 0.281,0.177 10 false G98 2.583,0.677 2.99,0.854 0.406,0.177 10 false CANH 2.542,1.823 2.927,2 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.104 1.365,2.281 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-4 (CANH) - G98-15 (CANL) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

60.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

NG

65.CONNECT CONNECTOR
60.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system (for 8 sensor type), go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".


a.
U149021E04
1.844,1.156 2.365,0.698 2.365,0.698 2.573,0.698 true 1.844,1.344 2.323,1.927 2.323,1.927 2.458,1.927 true 2.198,2.948 2.281,3.156 2.281,3.156 2.406,3.156 true 1.625,2.5 1.51,2.177 1.51,2.177 1.396,2.177 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G98 2.615,0.625 3.021,0.802 0.406,0.177 10 false CANH 2.49,1.844 2.875,2.021 0.385,0.177 10 false CANL 2.469,3.073 2.76,3.25 0.292,0.177 10 false BAT 1.135,2.094 1.365,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-5 (CANH) - G98-16 (CANL) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

61.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

67.CONNECT CONNECTOR
61.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
NOTICE:

For vehicles with 1KD-FTV, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Power Management Control ECU)".


a.
U170405E03
1.74,1.156 2.385,0.698 2.385,0.698 2.594,0.698 true 1.74,1.365 2.333,1.948 2.333,1.948 2.469,1.948 true 2.208,2.969 2.292,3.177 2.292,3.177 2.417,3.177 true 1.635,2.51 1.521,2.188 1.521,2.188 1.406,2.188 true 0.406,0.969 0.688,1.146 0.281,0.177 10 false G98 2.635,0.667 3.042,0.844 0.406,0.177 10 false CANH 2.479,1.844 2.865,2.021 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.156,2.115 1.385,2.292 0.229,0.177 10 false CG 0.406,2.677 0.688,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-6 (CANH) - G98-17 (CANL) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

62.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

69.CONNECT CONNECTOR
62.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U149022E04
2.198,1.167 2.448,0.854 2.448,0.854 2.667,0.854 true 2.188,1.365 2.438,1.792 2.438,1.792 2.573,1.792 true 2.198,2.948 2.281,3.156 2.281,3.156 2.406,3.156 true 1.625,2.51 1.51,2.188 1.51,2.188 1.396,2.188 true 0.417,0.979 0.698,1.156 0.281,0.177 10 false G98 2.708,0.823 3.115,1 0.406,0.177 10 false CANH 2.604,1.708 2.99,1.885 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.094 1.365,2.271 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-2 (CANH) - G98-13 (CANL) Engine switch off 108 to 132 Ω
G98-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

71.CONNECT CONNECTOR
63.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

64.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
64.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
a.
U148708E01
2.293,0.527 2.702,0.694 0.409,0.167 10 CANL 2.443,0.775 2.887,0.942 0.444,0.167 10 CANH 2.033,1.084 2.197,0.601 2.197,0.601 2.281,0.601 false 2.403,0.85 2.317,0.85 2.317,0.85 2.106,1.09 false 0.435,0.939 0.739,1.117 0.304,0.178 10 A49 0.449,2.651 0.772,2.829 0.324,0.178 10 G48 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 1.136,2.103 1.371,2.281 0.235,0.178 10 CG 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 1.667,2.494 1.513,2.192 1.513,2.192 1.425,2.192 false 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false

Disconnect the A49 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) Engine switch off 54 to 69 Ω
A49-7 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A49-8 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A49-7 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A49-8 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)
*b Front view of DLC3



OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)

65.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

66.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
66.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U170217E02
0.708,0.667 0.865,0.667 0.865,0.667 1.042,1.063 true 0.771,1.729 0.958,1.729 0.958,1.729 1.063,1.177 true 1.667,2.49 1.51,2.188 1.51,2.188 1.427,2.188 true 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 true 0.365,1.656 0.75,1.833 0.385,0.177 10 false CA2H 0.333,0.583 0.698,0.76 0.365,0.177 10 false CA2L 1.51,0.188 1.865,0.365 0.354,0.177 10 false G119 0.448,2.688 0.771,2.865 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.104 1.375,2.281 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G119-39 (CA2H) - G119- 17 (CA2L) Engine switch off 54 to 69 Ω
G119-39 (CA2H) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-17 (CA2L) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-39 (CA2H) - G48- 16 (BAT) Engine switch off 6 kΩ or higher
G119-17 (CA2L) - G48- 16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT ECU ASSEMBLY (CA2H, CA2L)

67.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

68.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
68.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U170322E01
1.185,1.047 0.88,0.749 0.88,0.749 0.729,0.749 false 0.483,0.667 0.681,0.804 0.198,0.137 10 R1 0.726,0.362 0.923,0.498 0.196,0.137 10 R2 0.064,0.068 0.506,0.205 0.442,0.137 10 *a 1.582,0.343 1.949,0.479 0.367,0.137 10 G154 0.064,1.878 0.506,2.015 0.442,0.137 10 *b 0.422,2.566 0.704,2.702 0.281,0.137 10 G48 2.213,2.858 2.377,3.15 2.377,3.15 2.531,3.15 false 2.554,3.071 2.942,3.208 0.389,0.137 10 BAT 0.987,2 1.376,2.136 0.389,0.137 10 CG 1.669,2.448 1.46,2.074 1.46,2.074 1.305,2.074 false 1.408,1.047 1.119,0.447 1.119,0.447 0.969,0.447 false

Disconnect the G154 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G154-3 (R1) - G154-5 (R2) Engine switch off 54 to 69 Ω
G154-3 (R1) - G48-4 (CG) Engine switch off 200 Ω or higher
G154-5 (R2) - G48-4 (CG) Engine switch off 200 Ω or higher
G154-3 (R1) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G154-5 (R2) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)

69.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

70.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
70.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U148534E03
2.302,2.813 2.51,3.052 2.51,3.052 2.563,3.052 true 1.698,2.333 1.49,2.104 1.49,2.104 1.438,2.104 true 1.969,1.146 2.344,0.573 2.344,0.573 2.469,0.573 true 1.823,1.156 2.042,0.292 2.042,0.292 2.177,0.292 true 0.104,1.906 0.302,2.073 0.198,0.167 10 false *b 0.365,2.51 0.677,2.688 0.313,0.177 10 false G48 1.135,2 1.365,2.177 0.229,0.177 10 false CG 2.604,2.958 2.958,3.135 0.354,0.177 10 false BAT 0.115,0.052 0.292,0.26 0.177,0.208 10 false *a 0.76,0.271 1.073,0.448 0.313,0.177 10 false G25 2.229,0.208 2.667,0.417 0.438,0.208 10 false CANH 2.5,0.49 2.938,0.698 0.438,0.208 10 false CANL

Disconnect the G25 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) Engine switch off 54 to 69 Ω
G25-11 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-11 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G25-11 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

71.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

72.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
72.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
a.
U169952E02
1.115,1.552 1.188,1.552 1.188,1.552 1.573,1.229 true 1.292,1.802 1.375,1.802 1.375,1.802 1.625,1.229 true 2.292,2.917 2.5,3.146 2.5,3.146 2.552,3.146 true 1.677,2.479 1.5,2.167 1.5,2.167 1.333,2.167 true 2.479,0.813 2.406,0.813 2.406,0.813 1.896,1.094 true 2.302,0.49 2.219,0.49 2.219,0.49 1.802,1.073 true 0.094,0.042 0.292,0.25 0.198,0.208 10 false *a 0.469,0.875 0.802,1.083 0.333,0.208 10 false G51 0.063,1.969 0.26,2.135 0.198,0.167 10 false *b 0.385,2.625 0.698,2.802 0.313,0.177 10 false G48 1.083,2.083 1.313,2.26 0.229,0.177 10 false CG 2.615,3.063 2.969,3.24 0.354,0.177 10 false BAT 0.771,1.708 1.396,1.865 0.625,0.156 10 false CA2L*A 0.573,1.458 1.208,1.615 0.635,0.156 10 false CA2H*A 2.521,0.76 3.146,0.917 0.625,0.156 10 false CA3N*B 2.344,0.427 2.979,0.583 0.635,0.156 10 false CA3P*B

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G48-16 (BAT) Engine switch off 6 kΩ or higher

for 1GR-FE, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV
*B for 1GR-FE, 1GD-FTV
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of DLC3

Result
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 1GR-FE, 1GD-FTV) C



A

B

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA2H, CA2L)

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA3P, CA3H)

73.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U148244E03
2.604,0.604 2.531,0.604 2.531,0.604 2.354,1.146 true 2.448,1.156 2.667,0.844 2.667,0.844 2.76,0.844 true 1.042,1.677 1.115,1.677 1.115,1.677 1.448,1.188 true 1.354,1.188 0.979,1.438 0.979,1.438 0.885,1.438 true 0.031,0.031 0.271,0.219 0.24,0.188 10 true *a 2.771,0.771 3.198,0.927 0.427,0.156 10 false AM22 0.479,1.354 0.823,1.51 0.344,0.156 10 false GND 0.51,1.604 0.938,1.76 0.427,0.156 10 false GND2 2.615,0.521 3.021,0.677 0.406,0.156 10 false AM21 2.802,1.281 3.135,1.438 0.333,0.156 10 false G51

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



b.

Disconnect the G51 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-5 (GND2) - Body ground Always Below 1 Ω
G51-6 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-1 (AM22) - Body ground Always 11 to 14 V
G51-2 (AM21) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR