Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › from 2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260591 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



Hide 22100 2.INSTALL SUPPLY PUMP ASSEMBLY

NOTICE:
A354097

·

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the supply pump assembly.


c.
A347065C03
0.958,1.594 1.146,1.594 1.146,1.594 1.427,1.208 true 0.75,1.51 1.063,1.667 0.313,0.156 10 true *a
*a Groove


A343559C04
2.125,3.302 2.292,2.646 2.292,2.646 2.51,2.646 false 2.521,2.521 2.833,2.677 0.313,0.156 10 false *a 1.208,2.198 1.521,2.354 0.313,0.156 10 false *b 3.063,3.406 3.375,3.563 0.313,0.156 10 false 6°
*a Supply Pump Shaft Key
*b Upper Side


To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.

HINT:

When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.



d.
A347066C02
1.635,1.74 2.208,1.74 false 1.156,2.125 1.885,2.125 1.885,2.125 1.885,1.74 false 2.438,0.792 2.583,0.969 2.583,0.969 2.823,0.969 true 0.802,1.979 1.115,2.135 0.313,0.156 10 false *a 2.24,1.635 2.719,1.823 0.479,0.188 10 true SST 2.854,0.875 3.333,1.063 0.479,0.188 10 true SST
*a Hold
V100135

Turn


Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  


e.
A344940

Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.



f.

Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.

Remove SST and the 3 set bolts.


h.
A347061C03
0.948,2.052 1.573,2.052 1.573,2.052 1.573,1.885 false 1.281,1.885 1.844,1.885 false 0.5,1.958 0.813,2.115 0.313,0.156 10 false *a 1.875,1.802 2.333,2 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley subassembly and tighten the set nut.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 11324 3.INSTALL TIMING CHAIN COVER PLATE

a.

Install the timing chain cover plate and new gasket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.INSTALL FUEL PUMP MOTOR WIRE

a.

Attach the clamp and install the fuel pump motor wire.


b.

Connect the fuel pump motor wire connector.


Hide 22803 5.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

a.

Install the fuel injection pump cover sub-assembly to the supply pump assembly.


Hide 6.INSTALL NO. 4 FUEL PIPE (w/o DPF)

a.
A370020E01
0.271,2.292 0.479,2.469 0.208,0.177 10 true 1 1.781,2.958 1.99,3.135 0.208,0.177 10 true 2

Tighten the No. 4 fuel pipe with the 2 union bolts and bolts with 2 new gaskets in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 23271H 7.INSTALL NO. 1 FUEL HOSE

a.

Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clamps to secure it.


Hide 23273C 8.INSTALL NO. 2 FUEL HOSE

a.

Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clamps to secure it.


Hide 16620 9.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 82123 11.CONNECT NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

Hide 88359 12.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 13.CONNECT OIL COOLER HOSE (for Automatic Transmission)

Hide 16470 14.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 16640 15.INSTALL INTERCOOLER RESERVOIR ASSEMBLY (w/ Urea SCR System)

Hide 16554B 16.INSTALL NO. 4 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16553B 17.INSTALL NO. 3 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 161B0 18.INSTALL ELECTRIC WATER PUMP ASSEMBLY (w/ Urea SCR System)

Hide 16551B 19.INSTALL NO. 1 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16552B 20.INSTALL NO. 2 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16571C 21.INSTALL NO. 1 RADIATOR HOSE

Hide 17342F 22.INSTALL NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17341K 23.INSTALL INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 26. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 51405A 29.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY