Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2020.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0441313 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Speaker Circuit  


DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E451437E01
2.375,2.083 2.635,2.281 0.26,0.198 10 false FR- 2.406,6.813 2.75,6.99 0.344,0.177 10 false FL- 2.375,6.375 2.792,6.542 0.417,0.167 10 false FL+ 2.26,5.146 2.677,5.313 0.417,0.167 10 false WFR- 2.25,4.74 2.667,4.906 0.417,0.167 10 false WFR+ 2.365,1.625 2.677,1.802 0.313,0.177 10 false FR+ 5.823,1.271 6.26,1.427 0.438,0.156 10 false TWR- 5.813,0.906 6.229,1.073 0.417,0.167 10 false TWR+ 3.531,6.813 3.938,6.979 0.406,0.167 10 false TWL- 3.521,6.396 3.927,6.563 0.406,0.167 10 false TWL+ 3.917,6.219 4.094,6.385 0.177,0.167 10 false - 3.906,6.021 4.063,6.208 0.156,0.188 10 false + 5.833,2.021 5.927,2.208 0.094,0.188 10 false - 5.823,1.646 5.979,1.813 0.156,0.167 10 false + 0.51,2.281 0.969,2.469 0.458,0.188 10 false WF2- 1.792,2.271 2.344,2.438 0.552,0.167 10 false WF2- 0.49,1.802 0.927,1.969 0.438,0.167 10 false WF2+ 1.792,1.813 2.344,1.979 0.552,0.167 10 false WF2+ 0.51,1.323 0.958,1.5 0.448,0.177 10 false WF1- 1.792,5.125 2.344,5.292 0.552,0.167 10 false MR- 1.792,4.667 2.344,4.833 0.552,0.167 10 false MR+ 1.792,1.323 2.344,1.49 0.552,0.167 10 false WF1- 0.51,0.844 1.021,1.021 0.51,0.177 10 false WF1+ 1.792,0.844 2.344,1.01 0.552,0.167 10 false WF1+ 5.49,2.458 6.75,2.813 1.26,0.354 10 false Front No. 3 Speaker Assembly RH 0.146,5.573 1.51,5.927 1.365,0.354 10 false Rear Header Speaker Assembly RH 5.51,4.094 6.802,4.458 1.292,0.365 10 false Front No. 2 Speaker Assembly RH 4.156,5.5 6.354,5.708 2.198,0.208 10 false Front No. 1 Speaker Assembly RH 3.208,7.24 4.49,7.625 1.281,0.385 10 false Front No. 3 Speaker Assembly LH 4.646,6.656 5.906,7.031 1.26,0.375 10 false Front No. 2 Speaker Assembly LH 0.156,2.969 1.417,3.406 1.26,0.438 10 false No. 1 Speaker with Box Assembly 1.094,7.865 3.51,8.083 2.417,0.219 10 false Stereo Component Amplifier Assembly 0.135,0.083 1.25,0.292 1.115,0.208 12 false for JBL Made: 3.948,1.625 4.323,1.792 0.375,0.167 10 false SPI+ 3.948,2.083 4.323,2.25 0.375,0.167 10 false SPI- 3.938,0.896 4.375,1.073 0.438,0.177 10 false SPO+ 3.948,1.281 4.385,1.458 0.438,0.177 10 false SPO- 3.542,1.552 3.719,1.74 0.177,0.188 10 false *1 3.313,2 3.49,2.188 0.177,0.188 10 false *1 4.177,0.052 4.354,0.24 0.177,0.188 10 false *2 3.99,0.344 4.167,0.531 0.177,0.188 10 false *2 3.615,2.646 4.74,3.01 1.125,0.365 10 false DCM (Telematics Transceiver)*1 0.125,8.25 1.99,8.427 1.865,0.177 10 false *1: w/ Telematics Transceiver 0.125,8.531 2.167,8.719 2.042,0.188 10 false *2: w/o Telematics Transceiver 0.99,0.74 1.135,0.938 0.146,0.198 10 false 1 0.99,1.219 1.135,1.417 0.146,0.198 10 false 3 0.979,1.698 1.125,1.896 0.146,0.198 10 false 2 0.979,2.177 1.125,2.375 0.146,0.198 10 false 4 0.156,2.813 0.49,3 0.333,0.188 10 false R24 1.49,0.646 1.625,0.823 0.135,0.177 10 false 1 1.406,0.854 1.729,1.031 0.323,0.177 10 false H65 1.396,1.313 1.719,1.49 0.323,0.177 10 false H65 1.5,1.115 1.635,1.292 0.135,0.177 10 false 5 1.49,1.583 1.625,1.76 0.135,0.177 10 false 2 1.396,1.792 1.719,1.969 0.323,0.177 10 false H65 1.406,2.281 1.729,2.458 0.323,0.177 10 false H65 1.479,2.083 1.625,2.281 0.146,0.198 10 false 6 2.771,1.635 3.094,1.813 0.323,0.177 10 false H65 2.865,1.427 3,1.604 0.135,0.177 10 false 4 2.813,1.885 3,2.063 0.188,0.177 10 false 10 2.792,2.083 3.115,2.26 0.323,0.177 10 false H65 3.771,1.542 3.917,1.74 0.146,0.198 10 false 2 3.781,1.99 3.927,2.188 0.146,0.198 10 false 3 4.406,0.813 4.552,0.979 0.146,0.167 10 false 5 4.406,1.177 4.552,1.344 0.146,0.167 10 false 6 3.615,2.469 4.031,2.635 0.417,0.167 10 false G187 0.979,4.552 1.125,4.75 0.146,0.198 10 false 2 0.969,5.031 1.115,5.229 0.146,0.198 10 false 1 0.135,5.417 0.469,5.604 0.333,0.188 10 false Q15 1.396,4.656 1.719,4.833 0.323,0.177 10 false H66 1.385,5.156 1.708,5.333 0.323,0.177 10 false H66 1.49,4.458 1.635,4.656 0.146,0.198 10 false 2 1.49,4.948 1.635,5.146 0.146,0.198 10 false 7 2.76,4.76 3.083,4.938 0.323,0.177 10 false H66 2.771,5.167 3.094,5.344 0.323,0.177 10 false H66 2.813,4.552 3,4.729 0.188,0.177 10 false 10 2.865,4.969 3.031,5.156 0.167,0.188 10 false 9 4.708,4.667 4.854,4.865 0.146,0.198 10 false 1 4.719,5.063 4.865,5.26 0.146,0.198 10 false 2 4.167,5.344 4.333,5.51 0.167,0.167 10 false J4 2.771,6.396 3.094,6.573 0.323,0.177 10 false H65 2.771,6.813 3.094,6.99 0.323,0.177 10 false H65 2.865,6.198 3.031,6.385 0.167,0.188 10 false 3 2.865,6.615 3.031,6.802 0.167,0.188 10 false 9 3.333,6.292 3.5,6.479 0.167,0.188 10 false 1 3.323,6.708 3.49,6.896 0.167,0.188 10 false 2 4.104,5.927 4.25,6.104 0.146,0.177 10 false 3 4.104,6.135 4.25,6.313 0.146,0.177 10 false 4 4.708,5.927 4.875,6.115 0.167,0.188 10 false 2 4.698,6.135 4.844,6.333 0.146,0.198 10 false 1 4.646,6.49 4.938,6.677 0.292,0.188 10 false H13 3.208,7.083 3.5,7.271 0.292,0.188 10 false H22 5.594,0.792 5.74,0.99 0.146,0.198 10 false 1 5.615,1.177 5.76,1.375 0.146,0.198 10 false 2 5.615,1.563 5.76,1.76 0.146,0.198 10 false 3 5.604,1.927 5.75,2.104 0.146,0.177 10 false 4 5.49,2.302 5.802,2.49 0.313,0.188 10 false H21 5.625,3.198 5.771,3.385 0.146,0.188 10 false 2 5.615,3.573 5.76,3.76 0.146,0.188 10 false 1 5.51,3.938 5.823,4.125 0.313,0.188 10 false H10

E451438E01
0.167,0.104 1.292,0.302 1.125,0.198 12 false for JBL Made: 2.406,6.094 2.813,6.26 0.406,0.167 10 false RL- 2.396,5.656 2.802,5.823 0.406,0.167 10 false RL+ 3.521,6.063 3.927,6.229 0.406,0.167 10 false -TW 3.5,5.656 3.906,5.823 0.406,0.167 10 false +TW 3.927,5.49 4.333,5.656 0.406,0.167 10 false - 3.927,5.302 4.094,5.49 0.167,0.188 10 false + 2.375,3.719 2.677,3.906 0.302,0.188 10 false RR- 2.26,1.344 2.677,1.51 0.417,0.167 10 false WFL- 2.26,0.896 2.677,1.063 0.417,0.167 10 false WFL+ 2.354,3.292 2.656,3.49 0.302,0.198 10 false RR+ 3.51,3.698 3.917,3.865 0.406,0.167 10 false -TW 3.521,3.281 3.927,3.448 0.406,0.167 10 false +TW 3.906,3.115 4.313,3.281 0.406,0.167 10 false - 3.917,2.917 4.323,3.083 0.406,0.167 10 false + 1.781,2.177 2.333,2.344 0.552,0.167 10 false ML- 1.792,1.719 2.198,1.896 0.406,0.177 10 false ML+ 1.792,5.833 2.323,6.021 0.531,0.188 10 false CTR- 1.792,5.375 2.344,5.542 0.552,0.167 10 false CTR+ 0.177,6.281 1.458,6.719 1.281,0.438 10 false Front No. 4 Speaker Assembly 0.146,2.656 1.5,3.073 1.354,0.417 10 false Rear Header Speaker Assembly LH 4.583,1.75 5.865,2.104 1.281,0.354 10 false Front No. 1 Speaker Assembly LH 3.219,6.573 4.5,7.01 1.281,0.438 10 false Rear No. 2 Speaker Assembly LH 4.719,5.938 5.615,6.375 0.896,0.438 10 false Rear Speaker Set LH 3.198,4.125 4.49,4.521 1.292,0.396 10 false Rear No. 2 Speaker Assembly RH 4.729,3.542 5.615,3.906 0.885,0.365 10 false Rear Speaker Set RH 0.958,8 3.49,8.229 2.531,0.229 10 false Stereo Component Amplifier Assembly 2.76,0.896 3.063,1.073 0.302,0.177 10 false H66 2.865,0.688 3.021,0.875 0.156,0.188 10 false 3 2.854,1.146 3.01,1.333 0.156,0.188 10 false 8 2.771,1.344 3.073,1.521 0.302,0.177 10 false H66 4.698,0.802 4.854,0.99 0.156,0.188 10 false 1 4.708,1.24 4.865,1.427 0.156,0.188 10 false 2 4.583,1.583 4.813,1.76 0.229,0.177 10 false K3 2.76,3.292 3.063,3.469 0.302,0.177 10 false H66 2.771,3.708 3.073,3.885 0.302,0.177 10 false H66 2.875,3.083 3.031,3.271 0.156,0.188 10 false 5 2.823,3.51 3.021,3.688 0.198,0.177 10 false 12 3.344,3.188 3.5,3.375 0.156,0.188 10 false 1 3.344,3.604 3.5,3.792 0.156,0.188 10 false 2 3.208,3.958 3.438,4.135 0.229,0.177 10 false L3 4.729,3.385 4.958,3.563 0.229,0.177 10 false L1 4.094,2.813 4.25,3 0.156,0.188 10 false 3 4.104,3.031 4.26,3.219 0.156,0.188 10 false 4 4.719,2.823 4.875,3.01 0.156,0.188 10 false 1 4.719,3.031 4.927,3.208 0.208,0.177 10 false 2 2.771,5.677 3.073,5.854 0.302,0.177 10 false H66 2.781,6.094 3.083,6.271 0.302,0.177 10 false H66 2.865,5.458 3.063,5.635 0.198,0.177 10 false 4 2.813,5.885 3.01,6.063 0.198,0.177 10 false 11 3.333,5.563 3.49,5.75 0.156,0.188 10 false 1 3.333,5.979 3.49,6.167 0.156,0.188 10 false 2 4.104,5.198 4.26,5.385 0.156,0.188 10 false 3 4.104,5.396 4.26,5.583 0.156,0.188 10 false 4 4.719,5.188 4.875,5.375 0.156,0.188 10 false 1 4.719,5.406 4.927,5.583 0.208,0.177 10 false 2 4.719,5.781 4.948,5.958 0.229,0.177 10 false M1 1.396,1.729 1.698,1.906 0.302,0.177 10 false H66 1.49,1.51 1.646,1.698 0.156,0.188 10 false 1 1.49,2.01 1.646,2.198 0.156,0.188 10 false 6 1.396,2.198 1.698,2.375 0.302,0.177 10 false H66 0.146,2.5 0.448,2.677 0.302,0.177 10 false R13 0.99,1.615 1.146,1.802 0.156,0.188 10 false 2 0.979,2.083 1.135,2.271 0.156,0.188 10 false 1 1.396,5.354 1.698,5.531 0.302,0.177 10 false H65 1.406,5.854 1.708,6.031 0.302,0.177 10 false H65 1.49,5.146 1.688,5.323 0.198,0.177 10 false 8 1.5,5.646 1.698,5.823 0.198,0.177 10 false 7 0.177,6.115 0.479,6.292 0.302,0.177 10 false H14 3.219,6.385 3.521,6.563 0.302,0.177 10 false M3 1,5.24 1.198,5.417 0.198,0.177 10 false 2 1,5.708 1.198,5.885 0.198,0.177 10 false 1

E449841E03
2.396,1.74 2.802,1.906 0.406,0.167 10 false FR- 2.396,7.063 2.813,7.229 0.417,0.167 10 false FL- 2.396,6.719 2.813,6.885 0.417,0.167 10 false FL+ 2.25,4.125 2.667,4.292 0.417,0.167 10 false WFR- 2.24,3.792 2.656,3.958 0.417,0.167 10 false WFR+ 2.385,1.396 2.792,1.563 0.406,0.167 10 false FR+ 3.542,1.74 4.083,1.906 0.542,0.167 10 false TWR- 3.51,1.406 4.063,1.573 0.552,0.167 10 false TWR+ 3.531,7.063 3.938,7.229 0.406,0.167 10 false TWL- 3.51,6.729 3.917,6.896 0.406,0.167 10 false TWL+ 3.927,6.438 4.333,6.604 0.406,0.167 10 false - 3.927,6.26 4.333,6.427 0.406,0.167 10 false + 3.927,1.135 4.333,1.302 0.406,0.167 10 false - 3.927,0.927 4.333,1.094 0.406,0.167 10 false + 0.542,1.333 1.094,1.5 0.552,0.167 10 false WF1- 1.792,1.313 2.344,1.479 0.552,0.167 10 false WF1- 0.5,0.844 1.052,1.01 0.552,0.167 10 false WF1+ 1.792,0.854 2.344,1.021 0.552,0.167 10 false WF1+ 3.24,2.198 4.531,2.563 1.292,0.365 10 false Front No. 3 Speaker Assembly RH 4.677,1.583 5.958,1.938 1.281,0.354 10 false Front No. 2 Speaker Assembly RH 4.542,4.563 5.813,4.927 1.271,0.365 10 false Front No. 1 Speaker Assembly RH 3.26,7.51 4.542,7.865 1.281,0.354 10 false Front No. 3 Speaker Assembly LH 4.635,6.896 5.917,7.229 1.281,0.333 10 false Front No. 2 Speaker Assembly LH 0.156,2.021 1.354,2.427 1.198,0.406 10 false No. 1 Speaker with Box Assembly 1.156,8.177 3.583,8.385 2.427,0.208 10 false Stereo Component Amplifier Assembly 0.104,0.052 2.719,0.292 2.615,0.24 12 false for PIONEER Made (14 Speakers): 1.167,8.021 1.458,8.219 0.292,0.198 10 false H67 0.156,1.865 0.479,2.042 0.323,0.177 10 false R24 0.979,0.729 1.094,0.917 0.115,0.188 10 false 1 0.99,1.229 1.104,1.417 0.115,0.188 10 false 3 1.583,0.74 1.74,0.917 0.156,0.177 10 false 6 1.531,1.219 1.75,1.406 0.219,0.188 10 false 21 2.729,1.313 2.948,1.49 0.219,0.177 10 false 13 2.75,1.656 2.969,1.833 0.219,0.177 10 false 28 3.323,1.302 3.49,1.469 0.167,0.167 10 false 1 3.323,1.646 3.49,1.813 0.167,0.167 10 false 2 3.25,2.031 3.656,2.198 0.406,0.167 10 false H21 4.688,1.427 5.094,1.594 0.406,0.167 10 false H10 4.094,1.063 4.26,1.229 0.167,0.167 10 false 4 4.104,0.865 4.271,1.031 0.167,0.167 10 false 3 4.708,0.854 4.875,1.021 0.167,0.167 10 false 2 4.708,1.073 4.875,1.24 0.167,0.167 10 false 1 2.76,3.667 2.875,3.854 0.115,0.188 10 false 5 2.74,4.031 2.958,4.208 0.219,0.177 10 false 20 4.708,3.677 4.875,3.844 0.167,0.167 10 false 1 4.708,4.031 4.875,4.198 0.167,0.167 10 false 2 4.552,4.396 4.781,4.583 0.229,0.188 10 false J4 2.74,6.604 2.958,6.781 0.219,0.177 10 false 12 2.74,6.948 2.958,7.125 0.219,0.177 10 false 27 3.344,6.604 3.51,6.771 0.167,0.167 10 false 1 3.344,6.969 3.521,7.135 0.177,0.167 10 false 2 4.115,6.167 4.281,6.333 0.167,0.167 10 false 3 4.115,6.385 4.281,6.552 0.167,0.167 10 false 4 4.719,6.177 4.896,6.344 0.177,0.167 10 false 2 4.708,6.375 4.875,6.542 0.167,0.167 10 false 1 3.26,7.354 3.667,7.521 0.406,0.167 10 false H22 4.635,6.74 5.042,6.906 0.406,0.167 10 false H13

E449842E02
0.115,0.073 2.74,0.302 2.625,0.229 12 false for PIONEER Made (14 Speakers): 2.385,5.552 2.677,5.74 0.292,0.188 10 false RL- 2.385,5.208 2.708,5.396 0.323,0.188 10 false RL+ 2.375,1.771 2.698,1.958 0.323,0.188 10 false RR- 1.792,1.365 2.208,1.531 0.417,0.167 10 false WFL- 1.781,0.875 2.198,1.042 0.417,0.167 10 false WFL+ 2.375,1.417 2.76,1.594 0.385,0.177 10 false RR+ 4.083,1.76 4.49,1.927 0.406,0.167 10 false -TW 4.083,1.406 4.49,1.573 0.406,0.167 10 false +TW 4.479,1.167 4.594,1.354 0.115,0.188 10 false - 4.469,0.979 4.615,1.156 0.146,0.177 10 false + 1.792,5.844 2.344,6.01 0.552,0.167 10 false CTR- 1.792,5.354 2.344,5.521 0.552,0.167 10 false CTR+ 0.167,6.271 1.438,6.656 1.271,0.385 10 false Front No. 4 Speaker Assembly 3.76,3.958 5.115,4.333 1.354,0.375 10 false Rear Header Speaker Assembly RH 0.146,1.802 1.427,2.135 1.281,0.333 10 false Front No. 1 Speaker Assembly LH 3.76,2.188 5.01,2.552 1.25,0.365 10 false Rear No. 2 Speaker Assembly RH 5.833,1.615 6.719,1.99 0.885,0.375 10 false Rear Speaker Set RH 1.052,8.094 3.594,8.302 2.542,0.208 10 false Stereo Component Amplifier Assembly 3.698,7.76 5.052,8.135 1.354,0.375 10 false Rear Header Speaker Assembly LH 3.75,6.01 5,6.375 1.25,0.365 10 false Rear No. 2 Speaker Assembly LH 4.094,5.531 4.5,5.698 0.406,0.167 10 false -TW 4.094,5.208 4.5,5.375 0.406,0.167 10 false +TW 4.469,4.76 4.615,4.938 0.146,0.177 10 false + 4.458,4.948 4.573,5.135 0.115,0.188 10 false - 5.802,5.396 6.688,5.771 0.885,0.375 10 false Rear Speaker Set LH 0.156,1.635 0.573,1.802 0.417,0.167 10 false K3 0.99,0.771 1.156,0.938 0.167,0.167 10 false 1 0.99,1.24 1.156,1.406 0.167,0.167 10 false 2 1.563,0.771 1.729,0.938 0.167,0.167 10 false 4 1.521,1.26 1.75,1.448 0.229,0.188 10 false 19 1.063,7.938 1.479,8.104 0.417,0.167 10 false H67 2.75,1.313 2.979,1.5 0.229,0.188 10 false 9 2.74,1.667 2.969,1.854 0.229,0.188 10 false 24 3.885,1.323 4.052,1.49 0.167,0.167 10 false 1 3.885,1.667 4.052,1.833 0.167,0.167 10 false 2 3.76,2.021 4.083,2.208 0.323,0.188 10 false L3 4.667,1.083 4.833,1.25 0.167,0.167 10 false 4 4.667,0.875 4.833,1.042 0.167,0.167 10 false 3 5.802,0.875 5.969,1.042 0.167,0.167 10 false 1 5.802,1.094 5.969,1.26 0.167,0.167 10 false 2 5.844,1.458 6.167,1.646 0.323,0.188 10 false L1 3.896,2.979 4.063,3.146 0.167,0.167 10 false 2 3.875,3.469 4.042,3.635 0.167,0.167 10 false 1 3.75,3.802 4.073,3.99 0.323,0.188 10 false Q15 1.604,5.25 1.833,5.438 0.229,0.188 10 false 7 1.521,5.719 1.75,5.906 0.229,0.188 10 false 22 0.99,5.24 1.219,5.427 0.229,0.188 10 false 2 0.979,5.729 1.125,5.917 0.146,0.188 10 false 1 0.177,6.104 0.594,6.271 0.417,0.167 10 false H14 2.75,5.104 2.979,5.292 0.229,0.188 10 false 8 2.74,5.448 2.969,5.635 0.229,0.188 10 false 23 3.75,5.854 3.979,6.042 0.229,0.188 10 false M3 3.896,5.094 4.063,5.26 0.167,0.167 10 false 1 3.885,5.438 4.052,5.604 0.167,0.167 10 false 2 4.667,4.667 4.833,4.833 0.167,0.167 10 false 3 4.667,4.875 4.833,5.042 0.167,0.167 10 false 4 5.802,4.677 5.969,4.844 0.167,0.167 10 false 1 5.802,4.865 5.969,5.031 0.167,0.167 10 false 2 5.802,5.229 6.125,5.417 0.323,0.188 10 false M1 3.885,6.76 4.052,6.927 0.167,0.167 10 false 2 3.885,7.229 4.052,7.396 0.167,0.167 10 false 1 3.708,7.604 4,7.781 0.292,0.177 10 false R13

E449841E04
2.396,1.74 2.802,1.906 0.406,0.167 10 false FR- 2.396,7.063 2.813,7.229 0.417,0.167 10 false FL- 2.396,6.719 2.813,6.885 0.417,0.167 10 false FL+ 2.25,4.125 2.667,4.292 0.417,0.167 10 false WFR- 2.24,3.792 2.656,3.958 0.417,0.167 10 false WFR+ 2.385,1.396 2.792,1.563 0.406,0.167 10 false FR+ 3.542,1.74 4.083,1.906 0.542,0.167 10 false TWR- 3.51,1.406 4.063,1.573 0.552,0.167 10 false TWR+ 3.531,7.063 3.938,7.229 0.406,0.167 10 false TWL- 3.51,6.729 3.917,6.896 0.406,0.167 10 false TWL+ 3.927,6.438 4.333,6.604 0.406,0.167 10 false - 3.927,6.26 4.333,6.427 0.406,0.167 10 false + 3.927,1.135 4.333,1.302 0.406,0.167 10 false - 3.927,0.927 4.333,1.094 0.406,0.167 10 false + 0.542,1.333 1.094,1.5 0.552,0.167 10 false WF1- 1.792,1.313 2.344,1.479 0.552,0.167 10 false WF1- 0.5,0.844 1.052,1.01 0.552,0.167 10 false WF1+ 1.792,0.854 2.344,1.021 0.552,0.167 10 false WF1+ 3.25,2.177 4.542,2.542 1.292,0.365 10 false Front No. 3 Speaker Assembly RH 4.667,1.583 5.948,1.938 1.281,0.354 10 false Front No. 2 Speaker Assembly RH 4.563,4.542 5.833,4.906 1.271,0.365 10 false Front No. 1 Speaker Assembly RH 3.26,7.5 4.542,7.854 1.281,0.354 10 false Front No. 3 Speaker Assembly LH 4.646,6.885 5.927,7.219 1.281,0.333 10 false Front No. 2 Speaker Assembly LH 0.156,2.01 1.354,2.417 1.198,0.406 10 false No. 1 Speaker with Box Assembly 1.188,8.156 3.615,8.365 2.427,0.208 10 false Stereo Component Amplifier Assembly 0.104,0.052 2.719,0.292 2.615,0.24 12 false for PIONEER Made (12 Speakers): 0.146,1.844 0.531,2.031 0.385,0.188 10 false Q30 0.99,0.74 1.135,0.927 0.146,0.188 10 false 2 0.979,1.219 1.125,1.406 0.146,0.188 10 false 4 1.583,0.74 1.729,0.927 0.146,0.188 10 false 6 1.521,1.219 1.708,1.417 0.188,0.198 10 false 21 1.208,7.99 1.594,8.177 0.385,0.188 10 false H67 2.729,1.292 2.917,1.49 0.188,0.198 10 false 13 2.74,1.646 2.927,1.844 0.188,0.198 10 false 28 3.344,1.302 3.479,1.479 0.135,0.177 10 false 1 3.344,1.646 3.479,1.823 0.135,0.177 10 false 2 4.104,0.854 4.24,1.031 0.135,0.177 10 false 3 4.104,1.063 4.24,1.24 0.135,0.177 10 false 4 4.708,0.865 4.844,1.042 0.135,0.177 10 false 2 4.698,1.073 4.833,1.25 0.135,0.177 10 false 1 3.25,2.01 3.656,2.177 0.406,0.167 10 false H21 4.667,1.427 5.073,1.594 0.406,0.167 10 false H10 2.75,3.677 2.938,3.875 0.188,0.198 10 false 5 2.75,4.031 2.938,4.229 0.188,0.198 10 false 20 4.708,3.667 4.896,3.865 0.188,0.198 10 false 1 4.719,4.031 4.906,4.229 0.188,0.198 10 false 2 4.563,4.385 4.969,4.552 0.406,0.167 10 false J4 2.729,6.615 2.917,6.813 0.188,0.198 10 false 12 2.75,6.958 2.938,7.156 0.188,0.198 10 false 27 3.333,6.615 3.521,6.813 0.188,0.198 10 false 1 3.333,6.958 3.521,7.156 0.188,0.198 10 false 2 4.104,6.177 4.292,6.375 0.188,0.198 10 false 3 4.104,6.385 4.292,6.583 0.188,0.198 10 false 4 4.719,6.167 4.906,6.365 0.188,0.198 10 false 2 4.708,6.385 4.896,6.583 0.188,0.198 10 false 1 3.26,7.333 3.646,7.521 0.385,0.188 10 false H22 4.646,6.74 5.031,6.927 0.385,0.188 10 false H13

E449843E02
0.125,0.073 2.75,0.302 2.625,0.229 12 false for PIONEER Made (12 Speakers): 2.385,5.552 2.677,5.74 0.292,0.188 10 false RL- 2.385,5.208 2.708,5.396 0.323,0.188 10 false RL+ 2.365,1.802 2.688,1.99 0.323,0.188 10 false RR- 1.792,1.365 2.208,1.531 0.417,0.167 10 false WFL- 1.781,0.875 2.198,1.042 0.417,0.167 10 false WFL+ 2.375,1.417 2.76,1.594 0.385,0.177 10 false RR+ 1.792,5.844 2.344,6.01 0.552,0.167 10 false CTR- 1.792,5.354 2.344,5.521 0.552,0.167 10 false CTR+ 0.156,6.281 1.427,6.667 1.271,0.385 10 false Front No. 4 Speaker Assembly 3.75,4.01 5.104,4.385 1.354,0.375 10 false Rear Header Speaker Assembly RH 0.146,1.802 1.427,2.135 1.281,0.333 10 false Front No. 1 Speaker Assembly LH 3.938,2.188 4.823,2.563 0.885,0.375 10 false Rear Speaker Set RH 1.063,8.094 3.604,8.302 2.542,0.208 10 false Stereo Component Amplifier Assembly 3.677,7.74 5.031,8.115 1.354,0.375 10 false Rear Header Speaker Assembly LH 3.958,5.958 4.844,6.333 0.885,0.375 10 false Rear Speaker Set LH 0.156,1.635 0.573,1.802 0.417,0.167 10 false K3 0.979,0.792 1.146,0.99 0.167,0.198 10 false 1 1,1.25 1.167,1.448 0.167,0.198 10 false 2 1.073,7.938 1.385,8.135 0.313,0.198 10 false H67 1.573,0.771 1.74,0.969 0.167,0.198 10 false 4 1.51,1.25 1.708,1.438 0.198,0.188 10 false 19 2.74,1.313 2.896,1.51 0.156,0.198 10 false 9 2.729,1.667 2.927,1.854 0.198,0.188 10 false 24 3.906,1.313 4.073,1.51 0.167,0.198 10 false 1 3.906,1.667 4.073,1.865 0.167,0.198 10 false 2 3.938,2.031 4.354,2.198 0.417,0.167 10 false Q32 3.885,2.99 4.052,3.188 0.167,0.198 10 false 2 3.896,3.469 4.063,3.667 0.167,0.198 10 false 1 3.75,3.854 4.167,4.021 0.417,0.167 10 false Q15 3.958,5.802 4.375,5.969 0.417,0.167 10 false R37 3.885,5.104 4.052,5.302 0.167,0.198 10 false 1 3.896,5.448 4.063,5.646 0.167,0.198 10 false 2 2.75,5.115 2.917,5.313 0.167,0.198 10 false 8 2.75,5.458 2.969,5.625 0.219,0.167 10 false 23 3.896,6.771 4.063,6.969 0.167,0.198 10 false 2 3.865,7.24 4.031,7.438 0.167,0.198 10 false 1 3.688,7.594 4.104,7.76 0.417,0.167 10 false R13 1.594,5.25 1.76,5.448 0.167,0.198 10 false 7 1.531,5.74 1.708,5.938 0.177,0.198 10 false 22 1,5.25 1.167,5.448 0.167,0.198 10 false 2 0.99,5.729 1.156,5.927 0.167,0.198 10 false 1 0.156,6.115 0.573,6.281 0.417,0.167 10 false H14

E449844E02
2.396,1.74 2.802,1.906 0.406,0.167 10 false FR- 2.396,7.063 2.813,7.229 0.417,0.167 10 false FL- 2.396,6.719 2.813,6.885 0.417,0.167 10 false FL+ 2.25,4.125 2.667,4.292 0.417,0.167 10 false WFR- 2.24,3.792 2.656,3.958 0.417,0.167 10 false WFR+ 2.385,1.396 2.792,1.563 0.406,0.167 10 false FR+ 3.542,1.74 4.083,1.906 0.542,0.167 10 false TWR- 3.51,1.406 4.063,1.573 0.552,0.167 10 false TWR+ 3.531,7.063 3.938,7.229 0.406,0.167 10 false TWL- 3.51,6.729 3.917,6.896 0.406,0.167 10 false TWL+ 3.927,6.438 4.333,6.604 0.406,0.167 10 false - 3.927,6.26 4.333,6.427 0.406,0.167 10 false + 3.927,1.135 4.333,1.302 0.406,0.167 10 false - 3.927,0.927 4.333,1.094 0.406,0.167 10 false + 3.271,2.188 4.563,2.552 1.292,0.365 10 false Front No. 3 Speaker Assembly RH 4.677,1.583 5.958,1.938 1.281,0.354 10 false Front No. 2 Speaker Assembly RH 4.552,4.542 5.823,4.906 1.271,0.365 10 false Front No. 1 Speaker Assembly RH 3.229,7.479 4.51,7.833 1.281,0.354 10 false Front No. 3 Speaker Assembly LH 4.656,6.906 5.938,7.24 1.281,0.333 10 false Front No. 2 Speaker Assembly LH 1.146,8.156 3.573,8.365 2.427,0.208 10 false Stereo Component Amplifier Assembly 0.104,0.042 2.719,0.281 2.615,0.24 12 false for PIONEER Made (9 Speakers): 1.146,8 1.563,8.167 0.417,0.167 10 false H67 2.76,1.635 2.969,1.802 0.208,0.167 10 false 28 2.729,1.292 2.938,1.458 0.208,0.167 10 false 13 3.333,1.292 3.542,1.458 0.208,0.167 10 false 1 3.333,1.646 3.542,1.813 0.208,0.167 10 false 2 4.104,0.865 4.313,1.031 0.208,0.167 10 false 3 4.094,1.073 4.302,1.24 0.208,0.167 10 false 4 4.719,0.854 4.875,1.042 0.156,0.188 10 false 2 4.708,1.063 4.865,1.25 0.156,0.188 10 false 1 3.26,2.031 3.667,2.198 0.406,0.167 10 false H21 4.677,1.427 5.083,1.594 0.406,0.167 10 false H10 2.76,3.667 2.885,3.865 0.125,0.198 10 false 5 2.76,4.031 2.969,4.229 0.208,0.198 10 false 20 4.698,3.656 4.854,3.844 0.156,0.188 10 false 1 4.698,4.031 4.854,4.219 0.156,0.188 10 false 2 4.552,4.385 4.958,4.552 0.406,0.167 10 false J4 2.729,6.604 2.938,6.802 0.208,0.198 10 false 12 2.74,6.958 2.948,7.156 0.208,0.198 10 false 27 3.333,6.604 3.49,6.792 0.156,0.188 10 false 1 3.333,6.948 3.49,7.135 0.156,0.188 10 false 2 4.104,6.188 4.26,6.375 0.156,0.188 10 false 3 4.104,6.385 4.26,6.573 0.156,0.188 10 false 4 4.688,6.188 4.844,6.375 0.156,0.188 10 false 2 4.667,6.385 4.823,6.573 0.156,0.188 10 false 1 3.229,7.302 3.646,7.469 0.417,0.167 10 false H22 4.656,6.74 5.073,6.906 0.417,0.167 10 false H13

E449845E02
0.125,0.073 2.75,0.302 2.625,0.229 12 false for PIONEER Made (9 Speakers): 2.385,5.552 2.677,5.74 0.292,0.188 10 false RL- 2.385,5.208 2.708,5.396 0.323,0.188 10 false RL+ 2.365,1.802 2.688,1.99 0.323,0.188 10 false RR- 1.792,1.365 2.208,1.531 0.417,0.167 10 false WFL- 1.781,0.875 2.198,1.042 0.417,0.167 10 false WFL+ 2.375,1.417 2.76,1.594 0.385,0.177 10 false RR+ 1.792,5.844 2.344,6.01 0.552,0.167 10 false CTR- 1.792,5.354 2.344,5.521 0.552,0.167 10 false CTR+ 0.146,6.302 1.417,6.688 1.271,0.385 10 false Front No. 4 Speaker Assembly 0.188,1.792 1.469,2.125 1.281,0.333 10 false Front No. 1 Speaker Assembly LH 3.948,2.198 4.833,2.573 0.885,0.375 10 false Rear Speaker Set RH 1.073,8.083 3.615,8.292 2.542,0.208 10 false Stereo Component Amplifier Assembly 3.927,5.99 4.813,6.365 0.885,0.375 10 false Rear Speaker Set LH 1.083,7.938 1.375,8.125 0.292,0.188 10 false H67 1.594,0.771 1.885,0.958 0.292,0.188 10 false 4 1.542,1.25 1.833,1.438 0.292,0.188 10 false 19 1,0.771 1.292,0.958 0.292,0.188 10 false 1 1.021,1.25 1.313,1.438 0.292,0.188 10 false 2 0.177,1.635 0.448,1.802 0.271,0.167 10 false K3 2.74,1.323 2.906,1.51 0.167,0.188 10 false 9 2.74,1.667 2.958,1.844 0.219,0.177 10 false 24 3.885,1.313 4.052,1.5 0.167,0.188 10 false 1 3.906,1.688 4.073,1.875 0.167,0.188 10 false 2 3.958,2.042 4.281,2.229 0.323,0.188 10 false L1 2.76,5.094 2.979,5.271 0.219,0.177 10 false 8 2.74,5.448 2.958,5.625 0.219,0.177 10 false 23 3.896,5.104 4.115,5.281 0.219,0.177 10 false 1 3.906,5.448 4.125,5.625 0.219,0.177 10 false 2 3.927,5.833 4.219,6.021 0.292,0.188 10 false M1 1.604,5.24 1.823,5.417 0.219,0.177 10 false 7 1.01,5.25 1.229,5.427 0.219,0.177 10 false 2 0.979,5.698 1.198,5.875 0.219,0.177 10 false 1 0.156,6.135 0.708,6.302 0.552,0.167 10 false H14 1.542,5.719 2.094,5.885 0.552,0.167 10 false 22

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for JBL Made A
for PIONEER Made (14 Speakers) B
for PIONEER Made (12 Speakers) C
for PIONEER Made (9 Speakers) D



A

2.CHECK SPEAKER (OPERATION CHECK)

B

19.CHECK SPEAKER (OPERATION CHECK)

C

33.CHECK SPEAKER (OPERATION CHECK)

D

46.CHECK SPEAKER (OPERATION CHECK)
2.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly or front No. 3 speaker assembly B
Front No. 4 speaker assembly C
Rear No. 2 speaker assembly or rear speaker set D
Rear header speaker assembly E
No. 1 speaker with box assembly F


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

3.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

C

10.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

D

12.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

E

15.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

F

17.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H66 stereo component amplifier assembly connector.


b.

Disconnect the J4 and K3 front No. 1 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-10 (WFR+) - J4-1 Always Below 1 Ω
H66-10 (WFR+) - Body ground Always 10 kΩ or higher
H66-9 (WFR-) - J4-2 Always Below 1 Ω
H66-9 (WFR-) - Body ground Always 10 kΩ or higher
H66-3 (WFL+) - K3-1 Always Below 1 Ω
H66-3 (WFL+) - Body ground Always 10 kΩ or higher
H66-8 (WFL-) - K3-2 Always Below 1 Ω
H66-8 (WFL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

*: w/ Telematics Transceiver


a.

Disconnect the H65 stereo component amplifier assembly connector.


b.

Disconnect the H10 and H13 front No. 2 speaker assembly connectors.


c.

Disconnect the H21 and H22 front No. 3 speaker assembly connectors.


d.

Disconnect the G187 DCM (telematics transceiver) connector.*


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Telematics Transceiver
Tester Connection Condition Specified Condition
H65-4 (FR+) - G187-2 (SPI+) Always Below 1 Ω
H65-4 (FR+) - Body ground Always 10 kΩ or higher
H65-10 (FR-) - G187-3 (SPI-) Always Below 1 Ω
H65-10 (FR-) - Body ground Always 10 kΩ or higher
G187-5 (SPO+) - H21-1 (TWR+) Always Below 1 Ω
G187-5 (SPO+) - Body ground Always 10 kΩ or higher
G187-6 (SPO-) - H21-2 (TWR-) Always Below 1 Ω
G187-6 (SPO-) - Body ground Always 10 kΩ or higher
H21-3 (+) - H10-2 Always Below 1 Ω
H21-3 (+) - Body ground Always 10 kΩ or higher
H21-4 (-) - H10-1 Always Below 1 Ω
H21-4 (-) - Body ground Always 10 kΩ or higher
H65-3 (FL+) - H22-1 (TWL+) Always Below 1 Ω
H65-3 (FL+) - Body ground Always 10 kΩ or higher
H65-9 (FL-) - H22-2 (TWL-) Always Below 1 Ω
H65-9 (FL-) - Body ground Always 10 kΩ or higher
H22-3 (+) - H13-2 Always Below 1 Ω
H22-3 (+) - Body ground Always 10 kΩ or higher
H22-4 (-) - H13-1 Always Below 1 Ω
H22-4 (-) - Body ground Always 10 kΩ or higher

w/o Telematics Transceiver
Tester Connection Condition Specified Condition
H65-4 (FR+) - H21-1 (TWR+) Always Below 1 Ω
H65-4 (FR+) - Body ground Always 10 kΩ or higher
H65-10 (FR-) - H21-2 (TWR-) Always Below 1 Ω
H65-10 (FR-) - Body ground Always 10 kΩ or higher
H21-3 (+) - H10-2 Always Below 1 Ω
H21-3 (+) - Body ground Always 10 kΩ or higher
H21-4 (-) - H10-1 Always Below 1 Ω
H21-4 (-) - Body ground Always 10 kΩ or higher
H65-3 (FL+) - H22-1 (TWL+) Always Below 1 Ω
H65-3 (FL+) - Body ground Always 10 kΩ or higher
H65-9 (FL-) - H22-2 (TWL-) Always Below 1 Ω
H65-9 (FL-) - Body ground Always 10 kΩ or higher
H22-3 (+) - H13-2 Always Below 1 Ω
H22-3 (+) - Body ground Always 10 kΩ or higher
H22-4 (-) - H13-1 Always Below 1 Ω
H22-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK MODEL

NG

7.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

8.INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)

B

9.REPLACE FRONT NO. 3 SPEAKER ASSEMBLY
8.INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)
a.
E197427C12
2.281,0.885 2.427,0.302 2.427,0.302 2.708,0.302 true 2.479,0.896 2.563,0.552 2.563,0.552 2.75,0.552 true 0.958,0.875 0.875,0.271 0.875,0.271 0.792,0.271 true 0.75,0.885 0.719,0.531 0.719,0.531 0.635,0.531 true 2.802,0.479 3.146,0.667 0.344,0.188 10 false SPI+ 2.75,0.229 3.094,0.417 0.344,0.188 10 false SPI- 0.24,0.438 0.656,0.625 0.417,0.188 10 false SPO- 0.375,0.188 0.792,0.375 0.417,0.188 10 false SPO+ 0.063,0.031 0.479,0.219 0.417,0.188 10 false *a
*a Component without harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SPO+) - 2 (SPI+) Always Below 1 Ω
6 (SPO-) - 3 (SPI-) Always Below 1 Ω
5 (SPO+) - Body ground Always 10 kΩ or higher
6 (SPO-) - Body ground Always 10 kΩ or higher
2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE FRONT NO. 3 SPEAKER ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

9.REPLACE FRONT NO. 3 SPEAKER ASSEMBLY
a.

Replace the front No. 3 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

10.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H65 stereo component amplifier assembly connector.


b.

Disconnect the H14 front No. 4 speaker assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H65-8 (CTR+) - H14-2 Always Below 1 Ω
H65-8 (CTR+) - Body ground Always 10 kΩ or higher
H65-7 (CTR-) - H14-1 Always Below 1 Ω
H65-7 (CTR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK FRONT NO. 4 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
a.

Replace the front No. 4 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:

Connect all the connectors to the front No. 4 speaker assemblies that were disconnected.



Result:
Proceed to
OK
NG



OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

12.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H66 stereo component amplifier assembly connector.


b.

Disconnect the L1 and M1 rear speaker set connectors.


c.

Disconnect the L3 and M3 rear No. 2 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-5 (RR+) - L3-1 (+TW) Always Below 1 Ω
H66-5 (RR+) - Body ground Always 10 kΩ or higher
H66-12 (RR-) - L3-2 (-TW) Always Below 1 Ω
H66-12 (RR-) - Body ground Always 10 kΩ or higher
L3-3 (+) - L1-1 Always Below 1 Ω
L3-3 (+) - Body ground Always 10 kΩ or higher
L3-4 (-) - L1-2 Always Below 1 Ω
L3-4 (-) - Body ground Always 10 kΩ or higher
H66-4 (RL+) - M3-1 (+TW) Always Below 1 Ω
H66-4 (RL+) - Body ground Always 10 kΩ or higher
H66-11 (RL-) - M3-2 (-TW) Always Below 1 Ω
H66-11 (RL-) - Body ground Always 10 kΩ or higher
M3-3 (+) - M1-1 Always Below 1 Ω
M3-3 (+) - Body ground Always 10 kΩ or higher
M3-4 (-) - M1-2 Always Below 1 Ω
M3-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR SPEAKER SET

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT REAR SPEAKER SET


Result:
Proceed to
OK
NG



OK

14.CHECK REAR NO. 2 SPEAKER ASSEMBLY

NG

14.CHECK REAR NO. 2 SPEAKER ASSEMBLY
a.

Replace the rear No. 2 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

15.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H66 stereo component amplifier assembly connector.


b.

Disconnect the Q15 and R13 rear header speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-2 (MR+) - Q15-2 Always Below 1 Ω
H66-2 (MR+) - Body ground Always 10 kΩ or higher
H66-7 (MR-) - Q15-1 Always Below 1 Ω
H66-7 (MR-) - Body ground Always 10 kΩ or higher
H66-1 (ML+) - R13-2 Always Below 1 Ω
H66-1 (ML+) - Body ground Always 10 kΩ or higher
H66-6 (ML-) - R13-1 Always Below 1 Ω
H66-6 (ML-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK REAR HEADER SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK REAR HEADER SPEAKER ASSEMBLY
a.

Replace the rear header speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the rear header speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left rear header speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (REAR HEADER SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

17.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H65 stereo component amplifier assembly connector.


b.

Disconnect the R24 No. 1 speaker with box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H65-1 (WF1+) - R24-1 (WF1+) Always Below 1 Ω
H65-1 (WF1+) - Body ground Always 10 kΩ or higher
H65-5 (WF1-) - R24-3 (WF1-) Always Below 1 Ω
H65-5 (WF1-) - Body ground Always 10 kΩ or higher
H65-2 (WF2+) - R24-2 (WF2+) Always Below 1 Ω
H65-2 (WF2+) - Body ground Always 10 kΩ or higher
H65-6 (WF2-) - R24-4 (WF2-) Always Below 1 Ω
H65-6 (WF2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY
a.

Remove the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL


b.

Inspect the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY

19.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly or front No. 3 speaker assembly B
Front No. 4 speaker assembly C
Rear No. 2 speaker assembly, rear header speaker assembly or rear speaker set D
No. 1 speaker with box assembly E


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

20.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

B

22.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

C

25.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

D

27.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

E

31.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
20.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the J4 and K3 front No. 1 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-5 (WFR+) - J4-1 Always Below 1 Ω
H67-5 (WFR+) - Body ground Always 10 kΩ or higher
H67-20 (WFR-) - J4-2 Always Below 1 Ω
H67-20 (WFR-) - Body ground Always 10 kΩ or higher
H67-4 (WFL+) - K3-1 Always Below 1 Ω
H67-4 (WFL+) - Body ground Always 10 kΩ or higher
H67-19 (WFL-) - K3-2 Always Below 1 Ω
H67-19 (WFL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

22.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H10 and H13 front No. 2 speaker assembly connectors.


c.

Disconnect the H21 and H22 front No. 3 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-13 (FR+) - H21-1 (TWR+) Always Below 1 Ω
H67-13 (FR+) - Body ground Always 10 kΩ or higher
H67-28 (FR-) - H21-2 (TWR-) Always Below 1 Ω
H67-28 (FR-) - Body ground Always 10 kΩ or higher
H21-3 (+) - H10-2 Always Below 1 Ω
H21-3 (+) - Body ground Always 10 kΩ or higher
H21-4 (-) - H10-1 Always Below 1 Ω
H21-4 (-) - Body ground Always 10 kΩ or higher
H67-12 (FL+) - H22-1 (TWL+) Always Below 1 Ω
H67-12 (FL+) - Body ground Always 10 kΩ or higher
H67-27 (FL-) - H22-2 (TWL-) Always Below 1 Ω
H67-27 (FL-) - Body ground Always 10 kΩ or higher
H22-3 (+) - H13-2 Always Below 1 Ω
H22-3 (+) - Body ground Always 10 kΩ or higher
H22-4 (-) - H13-1 Always Below 1 Ω
H22-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

24.CHECK FRONT NO. 3 SPEAKER ASSEMBLY

NG

24.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
a.

Replace the front No. 3 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

25.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H14 front No. 4 speaker assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-7 (CTR+) - H14-2 Always Below 1 Ω
H67-7 (CTR+) - Body ground Always 10 kΩ or higher
H67-22 (CTR-) - H14-1 Always Below 1 Ω
H67-22 (CTR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY
a.

Remove the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

27.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the L1 and M1 rear speaker set connectors.


c.

Disconnect the L3 and M3 rear No. 2 speaker assembly connectors.


d.

Disconnect the Q15 and R13 rear header speaker assembly connectors.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-9 (RR+) - L3-1 (+TW) Always Below 1 Ω
H67-9 (RR+) - Q15-2 Always Below 1 Ω
H67-9 (RR+) - Body ground Always 10 kΩ or higher
H67-24 (RR-) - L3-2 (-TW) Always Below 1 Ω
H67-24 (RR-) - Q15-1 Always Below 1 Ω
H67-24 (RR-) - Body ground Always 10 kΩ or higher
L3-3 (+) - L1-1 Always Below 1 Ω
L3-3 (+) - Body ground Always 10 kΩ or higher
L3-4 (-) - L1-2 Always Below 1 Ω
L3-4 (-) - Body ground Always 10 kΩ or higher
H67-8 (RL+) - M3-1 (+TW) Always Below 1 Ω
H67-8 (RL+) - R13-2 Always Below 1 Ω
H67-8 (RL+) - Body ground Always 10 kΩ or higher
H67-23 (RL-) - M3-2 (-TW) Always Below 1 Ω
H67-23 (RL-) - R13-1 Always Below 1 Ω
H67-23 (RL-) - Body ground Always 10 kΩ or higher
M3-3 (+) - M1-1 Always Below 1 Ω
M3-3 (+) - Body ground Always 10 kΩ or higher
M3-4 (-) - M1-2 Always Below 1 Ω
M3-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

28.INSPECT REAR SPEAKER SET

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.INSPECT REAR SPEAKER SET


Result:
Proceed to
OK
NG



OK

29.INSPECT REAR HEADER SPEAKER ASSEMBLY

NG

29.INSPECT REAR HEADER SPEAKER ASSEMBLY
a.

Remove the rear header speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL


b.

Inspect the rear header speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

30.CHECK REAR NO. 2 SPEAKER ASSEMBLY

NG

30.CHECK REAR NO. 2 SPEAKER ASSEMBLY
a.

Replace the rear No. 2 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

31.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the R24 No. 1 speaker with box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-6 (WF1+) - R24-1 (WF1+) Always Below 1 Ω
H67-6 (WF1+) - Body ground Always 10 kΩ or higher
H67-21 (WF1-) - R24-3 (WF1-) Always Below 1 Ω
H67-21 (WF1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

32.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY
a.

Remove the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL


b.

Inspect the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY

33.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly or front No. 3 speaker assembly B
Front No. 4 speaker assembly C
Rear header speaker assembly or rear speaker set D
No. 1 speaker with box assembly E


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

34.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

B

36.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

C

39.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

D

41.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

E

44.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
34.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the J4 and K3 front No. 1 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-5 (WFR+) - J4-1 Always Below 1 Ω
H67-5 (WFR+) - Body ground Always 10 kΩ or higher
H67-20 (WFR-) - J4-2 Always Below 1 Ω
H67-20 (WFR-) - Body ground Always 10 kΩ or higher
H67-4 (WFL+) - K3-1 Always Below 1 Ω
H67-4 (WFL+) - Body ground Always 10 kΩ or higher
H67-19 (WFL-) - K3-2 Always Below 1 Ω
H67-19 (WFL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

35.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

36.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H10 and H13 front No. 2 speaker assembly connectors.


c.

Disconnect the H21 and H22 front No. 3 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-13 (FR+) - H21-1 (TWR+) Always Below 1 Ω
H67-13 (FR+) - Body ground Always 10 kΩ or higher
H67-28 (FR-) - H21-2 (TWR-) Always Below 1 Ω
H67-28 (FR-) - Body ground Always 10 kΩ or higher
H21-3 (+) - H10-2 Always Below 1 Ω
H21-3 (+) - Body ground Always 10 kΩ or higher
H21-4 (-) - H10-1 Always Below 1 Ω
H21-4 (-) - Body ground Always 10 kΩ or higher
H67-12 (FL+) - H22-1 (TWL+) Always Below 1 Ω
H67-12 (FL+) - Body ground Always 10 kΩ or higher
H67-27 (FL-) - H22-2 (TWL-) Always Below 1 Ω
H67-27 (FL-) - Body ground Always 10 kΩ or higher
H22-3 (+) - H13-2 Always Below 1 Ω
H22-3 (+) - Body ground Always 10 kΩ or higher
H22-4 (-) - H13-1 Always Below 1 Ω
H22-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

37.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

38.CHECK FRONT NO. 3 SPEAKER ASSEMBLY

NG

38.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
a.

Replace the front No. 3 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

39.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H14 front No. 4 speaker assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-7 (CTR+) - H14-2 Always Below 1 Ω
H67-7 (CTR+) - Body ground Always 10 kΩ or higher
H67-22 (CTR-) - H14-1 Always Below 1 Ω
H67-22 (CTR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

40.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY
a.

Remove the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

41.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the Q32 and R37 rear speaker set connectors.


c.

Disconnect the Q15 and R13 rear header speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-9 (RR+) - Q32-1 Always Below 1 Ω
H67-9 (RR+) - Q15-2 Always Below 1 Ω
H67-9 (RR+) - Body ground Always 10 kΩ or higher
H67-24 (RR-) - Q32-2 Always Below 1 Ω
H67-24 (RR-) - Q15-1 Always Below 1 Ω
H67-24 (RR-) - Body ground Always 10 kΩ or higher
H67-8 (RL+) - R37-1 Always Below 1 Ω
H67-8 (RL+) - R13-2 Always Below 1 Ω
H67-8 (RL+) - Body ground Always 10 kΩ or higher
H67-23 (RL-) - R37-2 Always Below 1 Ω
H67-23 (RL-) - R13-1 Always Below 1 Ω
H67-23 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

42.INSPECT REAR SPEAKER SET

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.INSPECT REAR SPEAKER SET


Result:
Proceed to
OK
NG



OK

43.INSPECT REAR HEADER SPEAKER ASSEMBLY

NG

43.INSPECT REAR HEADER SPEAKER ASSEMBLY
a.

Remove the rear header speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>REMOVAL


b.

Inspect the rear header speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

44.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the Q30 No. 1 speaker with box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-6 (WF1+) - Q30-2 (WF1+) Always Below 1 Ω
H67-6 (WF1+) - Body ground Always 10 kΩ or higher
H67-21 (WF1-) - Q30-4 (WF1-) Always Below 1 Ω
H67-21 (WF1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

45.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY
a.

Remove the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>REMOVAL


b.

Inspect the No. 1 speaker with box assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY

46.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly or front No. 3 speaker assembly B
Front No. 4 speaker assembly C
Rear speaker set D


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

47.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

B

49.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

C

52.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)

D

54.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
47.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the J4 and K3 front No. 1 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-5 (WFR+) - J4-1 Always Below 1 Ω
H67-5 (WFR+) - Body ground Always 10 kΩ or higher
H67-20 (WFR-) - J4-2 Always Below 1 Ω
H67-20 (WFR-) - Body ground Always 10 kΩ or higher
H67-4 (WFL+) - K3-1 Always Below 1 Ω
H67-4 (WFL+) - Body ground Always 10 kΩ or higher
H67-19 (WFL-) - K3-2 Always Below 1 Ω
H67-19 (WFL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

48.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

49.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H10 and H13 front No. 2 speaker assembly connectors.


c.

Disconnect the H21 and H22 front No. 3 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-13 (FR+) - H21-1 (TWR+) Always Below 1 Ω
H67-13 (FR+) - Body ground Always 10 kΩ or higher
H67-28 (FR-) - H21-2 (TWR-) Always Below 1 Ω
H67-28 (FR-) - Body ground Always 10 kΩ or higher
H21-3 (+) - H10-2 Always Below 1 Ω
H21-3 (+) - Body ground Always 10 kΩ or higher
H21-4 (-) - H10-1 Always Below 1 Ω
H21-4 (-) - Body ground Always 10 kΩ or higher
H67-12 (FL+) - H22-1 (TWL+) Always Below 1 Ω
H67-12 (FL+) - Body ground Always 10 kΩ or higher
H67-27 (FL-) - H22-2 (TWL-) Always Below 1 Ω
H67-27 (FL-) - Body ground Always 10 kΩ or higher
H22-3 (+) - H13-2 Always Below 1 Ω
H22-3 (+) - Body ground Always 10 kΩ or higher
H22-4 (-) - H13-1 Always Below 1 Ω
H22-4 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

50.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

50.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

51.CHECK FRONT NO. 3 SPEAKER ASSEMBLY

NG

51.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
a.

Replace the front No. 3 speaker assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL


b.

Check the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

52.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the H14 front No. 4 speaker assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-7 (CTR+) - H14-2 Always Below 1 Ω
H67-7 (CTR+) - Body ground Always 10 kΩ or higher
H67-22 (CTR-) - H14-1 Always Below 1 Ω
H67-22 (CTR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

53.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

53.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY
a.

Remove the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 4 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

54.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
a.

Disconnect the H67 stereo component amplifier assembly connector.


b.

Disconnect the L1 and M1 rear speaker set connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-9 (RR+) - L1-1 Always Below 1 Ω
H67-9 (RR+) - Body ground Always 10 kΩ or higher
H67-24 (RR-) - L1-2 Always Below 1 Ω
H67-24 (RR-) - Body ground Always 10 kΩ or higher
H67-8 (RL+) - M1-1 Always Below 1 Ω
H67-8 (RL+) - Body ground Always 10 kΩ or higher
H67-23 (RL-) - M1-2 Always Below 1 Ω
H67-23 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

55.INSPECT REAR SPEAKER SET

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.INSPECT REAR SPEAKER SET


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG