Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CAMSHAFT › from 2020.08
RM27T0E _51 Engine / Hybrid System _053662 1GR-FE ENGINE MECHANICAL _0260489 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 28800A 8.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 28800 10.REMOVE BATTERY

Hide 74431 11.REMOVE BATTERY TRAY

Hide 16571C 15.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 16.REMOVE NO. 2 RADIATOR HOSE

Hide 32907C 18.DISCONNECT OIL COOLER TUBE (w/ Warmer)

Hide 32907C 19.DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

Hide 21.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 17361 23.REMOVE AIR TUBE (w/ Secondary Air Injection System)

Hide 17362 24.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 25701 25.REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 25702 26.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 44310 28.DISCONNECT VANE PUMP ASSEMBLY

Hide 16604 29.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 82715 30.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 17168 31.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16206 34.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

Hide 11181A 37.REMOVE REAR CYLINDER HEAD COVER

Hide 11202 39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 40.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11324 41.REMOVE TIMING CHAIN COVER PLATE

a.
A224737

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 42.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A072945

Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.


b.
A224754E01
0.05,0 0.286,0.194 0.236,0.194 10 *A 0.05,2.41 0.286,2.604 0.236,0.194 10 *B 0.131,1.72 0.299,1.914 0.168,0.194 10 *1 3.086,3.813 3.294,4.007 0.208,0.194 10 *1 0.319,1.802 0.453,1.802 0.453,1.802 0.979,1.45 false 3.065,3.903 2.831,3.903 2.831,3.903 2.279,3.674 false

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

Text in Illustration
*A for Bank 2
*B for Bank 1
*1 Paint Mark

HINT:

If the marks are not aligned, turn the crankshaft again to align the marks.



c.

Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

HINT:

Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.



Hide 13540 43.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A226510E08
2.74,0.177 3.01,0.406 0.271,0.229 10 true 30° 3.104,0.865 3.292,1.031 0.188,0.167 10 false 0°

Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

HINT:

This prevents the valves and pistons from interfering with each other.



b.
A226547E10
1.51,0.375 1.354,0.375 1.354,0.375 1.073,1.042 true 0.417,1.823 0.615,1.823 0.615,1.823 1.01,1.188 true 1.531,0.302 1.719,0.469 0.188,0.167 10 false *1 0.188,1.75 0.375,1.948 0.188,0.198 10 false *2

Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.

Text in Illustration
*1 Lever Hole
*2 Tensioner Hole


c.
A072945

Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.


d.
A224739

Remove the 2 bolts and chain tensioner.

NOTICE:

Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.



Hide 13506 44.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A226507E08
2.771,1.24 3.021,1.417 0.25,0.177 10 true 30°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.


CAUTION:

As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.



b.
U149629E03
1.083,1.76 1.406,1.76 1.406,1.76 1.552,2.01 true 0.396,1.677 1.083,1.979 0.688,0.302 10 true 5° to 10°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.



c.
A224759

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 45.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
U147630E05
2.802,4.063 3,4.26 0.198,0.198 3.198,2.646 3.396,2.844 0.198,0.198 0.24,2.917 0.438,3.115 0.198,0.198 0.073,3.75 0.271,3.948 0.198,0.198 2.313,2.854 2.531,3.042 0.219,0.188 2.01,4.094 2.208,4.292 0.198,0.198 0.917,2.792 1.115,2.99 0.198,0.198 1.01,3.823 1.208,4.021 0.198,0.198 0.51,0.531 0.688,0.531 0.688,0.531 1.167,0.969 false 1.531,1.24 2.052,1.24 true 1.667,1.375 1.875,1.375 1.875,1.375 1.875,1.24 true 3,3.24 3.115,3.406 0.115,0.167 10 false 1 2.844,3.844 2.958,4.01 0.115,0.167 10 false 2 2.854,4.073 2.969,4.24 0.115,0.167 10 false 3 2.917,2.208 3.031,2.375 0.115,0.167 10 false 4 3,2.677 3.115,2.844 0.115,0.167 10 false 5 3.25,2.656 3.365,2.823 0.115,0.167 10 true 6 0.292,3.333 0.406,3.5 0.115,0.167 10 false 7 0.385,3.781 0.5,3.948 0.115,0.167 10 false 8 0.354,2.24 0.469,2.406 0.115,0.167 10 false 9 0.25,2.677 0.427,2.844 0.177,0.167 10 false 10 0.25,2.927 0.417,3.104 0.167,0.177 10 true 11 0.073,3.76 0.25,3.927 0.177,0.167 10 false 12 2.323,3.396 2.5,3.563 0.177,0.167 10 false 13 2.021,3.885 2.198,4.052 0.177,0.167 10 false 14 2.167,2.177 2.344,2.344 0.177,0.167 10 false 15 2.333,2.625 2.51,2.792 0.177,0.167 10 false 16 2.333,2.865 2.51,3.031 0.177,0.167 10 true 17 2.021,4.104 2.198,4.271 0.177,0.167 10 false 18 0.938,3.406 1.115,3.573 0.177,0.167 10 false 19 1.271,3.854 1.448,4.021 0.177,0.167 10 false 20 1.146,2.146 1.323,2.313 0.177,0.167 10 false 21 0.917,2.583 1.094,2.75 0.177,0.167 10 false 22 0.917,2.813 1.094,2.979 0.177,0.167 10 true 23 1.031,3.833 1.208,4 0.177,0.167 10 true 24 0.302,0.448 0.479,0.615 0.177,0.167 10 false *1 0.594,4.115 0.781,4.281 0.188,0.167 10 false *a 0.604,4.406 0.792,4.573 0.188,0.167 10 false *b 2.083,1.156 2.292,1.333 0.208,0.177 10 true *2

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Installation of Bolts and Washers for Temporary Installation of camshaft housing

HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)



NOTICE:
·

Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.




Hide 13512 46.REMOVE NO. 2 CAMSHAFT

a.
A224761

Remove the bolt of the No. 2 chain tensioner assembly.


b.
A224769

Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.


c.
A224763

While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13511 47.REMOVE CAMSHAFT

a.

Lift up the rear of the camshaft so that it is at an angle.


b.
A224767

Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224765

Suspend the chain with a string or equivalent.


Hide 13506 48.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A072945

Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.


b.
A224760

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 49.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
U147631E05
0.792,4.167 0.99,4.365 0.198,0.198 0.198,2.688 0.396,2.885 0.198,0.198 3.177,2.906 3.375,3.104 0.198,0.198 2.958,4.094 3.156,4.292 0.198,0.198 1.177,2.917 1.396,3.115 0.219,0.198 1.458,4.125 1.656,4.323 0.198,0.198 2.552,2.896 2.75,3.094 0.198,0.198 2.219,4.135 2.417,4.333 0.198,0.198 2.26,1.031 2.896,1.031 true 1.74,1.396 1.573,1.396 1.573,1.396 1.573,1.26 true 1.865,1.292 1.385,1.292 true 0.479,3.406 0.594,3.573 0.115,0.167 10 false 1 0.844,3.948 0.958,4.115 0.115,0.167 10 false 2 0.844,4.177 0.958,4.344 0.115,0.167 10 false 3 0.792,2.198 0.906,2.365 0.115,0.167 10 false 4 0.5,2.74 0.615,2.906 0.115,0.167 10 false 5 0.229,2.698 0.365,2.854 0.135,0.156 10 true 6 3.24,3.385 3.354,3.552 0.115,0.167 10 false 7 3,3.885 3.115,4.052 0.115,0.167 10 false 8 2.938,2.24 3.052,2.406 0.115,0.167 10 false 9 3.167,2.698 3.344,2.865 0.177,0.167 10 false 10 3.188,2.917 3.365,3.083 0.177,0.167 10 true 11 2.969,4.115 3.146,4.281 0.177,0.167 10 true 12 1.229,3.479 1.406,3.646 0.177,0.167 10 false 13 1.458,3.896 1.635,4.063 0.177,0.167 10 false 14 1.458,2.26 1.635,2.427 0.177,0.167 10 false 15 1.208,2.719 1.385,2.885 0.177,0.167 10 false 16 1.198,2.927 1.375,3.094 0.177,0.167 10 true 17 1.469,4.135 1.646,4.302 0.177,0.167 10 false 18 2.552,3.438 2.729,3.604 0.177,0.167 10 false 19 2.24,3.917 2.417,4.083 0.177,0.167 10 false 20 2.365,2.271 2.542,2.438 0.177,0.167 10 false 21 2.552,2.688 2.729,2.854 0.177,0.167 10 false 22 2.563,2.906 2.74,3.073 0.177,0.167 10 true 23 2.24,4.146 2.417,4.313 0.177,0.167 10 false 24 2.938,0.948 3.115,1.146 0.177,0.198 10 false *1 0.438,4.146 0.625,4.313 0.188,0.167 10 false *a 0.448,4.438 0.635,4.604 0.188,0.167 10 false *b 1.188,1.208 1.365,1.406 0.177,0.198 10 true *2

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Installation of Bolts and Washers for Temporary Installation of camshaft housing

HINT:
·

Arrange the removed parts so that they can be reinstalled in their original locations.

·

Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)

·

Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)



NOTICE:
·

Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.

·

Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.




Hide 13054 50.REMOVE NO. 4 CAMSHAFT

a.
A224762

Remove the bolt of the No. 3 chain tensioner assembly.


b.
A224770

Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.


c.
A224764

While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13053 51.REMOVE NO. 3 CAMSHAFT

a.

Lift up the rear of the camshaft so that it is at an angle.


b.
A224768

Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224766

Suspend the chain with a string or equivalent.


Hide 13050 52.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227959E06
2.042,0.854 2.427,0.125 2.427,0.125 2.531,0.125 true 0.656,1.948 0.51,1.948 0.51,1.948 0.333,1.667 false 0.979,0.885 0.729,0.24 0.729,0.24 0.563,0.24 true 1.385,1.104 1.938,1.885 true 1.26,1.552 1.5,1.875 1.5,1.875 2.083,1.875 true 0.344,0.167 0.531,0.344 0.188,0.177 10 false *1 2.125,1.771 2.313,1.948 0.188,0.177 10 false *1 2.604,0.042 2.802,0.219 0.198,0.177 10 false *2 0.76,1.885 0.958,2.073 0.198,0.188 10 false *3

Remove the flange bolt and camshaft timing gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.




Hide 13070A 53.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227960E10
0.323,1.635 0.479,1.854 0.479,1.854 0.615,1.854 false 0.396,0.552 0.656,0.552 0.656,0.552 0.927,0.854 false 0.854,1.177 0.656,0.552 false 1.229,1.615 1.365,1.802 1.365,1.802 1.844,1.802 false 1.313,1.25 1.74,1.802 true 2.01,0.781 2.25,0.156 2.25,0.156 2.385,0.156 true 2.427,0.073 2.615,0.26 0.188,0.188 10 false *2 0.646,1.771 0.844,1.948 0.198,0.177 10 false *3 0.177,0.427 0.354,0.615 0.177,0.188 10 false *1 1.865,1.719 2.042,1.906 0.177,0.188 10 false *1

Remove the flange bolt and camshaft timing exhaust gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.