Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly uses the fuel injection volume signal from the ECM, fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly receives a fuel injection volume signal from the ECM and detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

The fuel level warning light will come on when the fuel level is below 9.96 liters (10.5 US qts, 8.8 Imp. qts).


WIRING DIAGRAM

except 5L-E (for 5Door):
B598688E01
0.719,2.708 2.99,2.969 2.271,0.26 10 false Fuel Suction Plate Sub-assembly 2.771,0.479 3.229,0.677 0.458,0.198 10 false 1 2.781,0.958 3.24,1.156 0.458,0.198 10 false 3 2.781,1.448 3.24,1.646 0.458,0.198 10 false 2 2.417,0.563 2.875,0.76 0.458,0.198 10 false FV 2.417,1.042 2.875,1.24 0.458,0.198 10 false FR 2.406,1.542 2.865,1.74 0.458,0.198 10 false FE 1.01,1.885 2.229,2.281 1.219,0.396 10 false Fuel Sender Gauge Assembly 0.99,1.667 1.448,1.865 0.458,0.198 10 false A 4.708,0.563 5.167,0.76 0.458,0.198 10 false FV 4.698,1.031 5.156,1.229 0.458,0.198 10 false FR 4.688,1.521 5.146,1.719 0.458,0.198 10 false FE&B 4.417,0.552 4.875,0.75 0.458,0.198 10 false 24 4.417,1.031 4.875,1.229 0.458,0.198 10 false 27 4.458,1.521 4.917,1.719 0.458,0.198 10 false 3 5.823,1.99 6.281,2.188 0.458,0.198 10 false CPU 4.708,5.625 5.167,5.823 0.458,0.198 10 false G304 4.708,5.802 6.948,6.073 2.24,0.271 10 false Combination Meter Assembly 0.833,5.594 3.375,5.833 2.542,0.24 10 false Fuel Tank Vent Tube Sub-assembly* 1.76,0.688 2.219,0.885 0.458,0.198 10 false 1 1.76,1.146 2.219,1.344 0.458,0.198 10 false 3 1.771,1.615 2.229,1.813 0.458,0.198 10 false 2 2.375,4.333 2.833,4.531 0.458,0.198 10 false FV2 1.76,3.948 2.219,4.146 0.458,0.198 10 false 3 1.76,4.438 2.219,4.635 0.458,0.198 10 false 1 1.771,3.469 2.229,3.667 0.458,0.198 10 false 2 4.479,3.344 5,3.552 0.521,0.208 10 false 2 4.688,3.823 5.146,4.021 0.458,0.198 10 false FR* 2.344,3.354 2.802,3.552 0.458,0.198 10 false FE2 2.74,3.354 3.198,3.552 0.458,0.198 10 false 1 2.729,3.802 3.188,4 0.458,0.198 10 false 4 2.708,4.323 3.167,4.521 0.458,0.198 10 false 5 4.417,3.823 4.938,4.031 0.521,0.208 10 false 26 4.417,4.323 4.938,4.531 0.521,0.208 10 false 25 4.708,4.344 5.167,4.542 0.458,0.198 10 false L* 2.354,3.813 2.813,4.01 0.458,0.198 10 false FR2 4.688,3.365 5.146,3.563 0.458,0.198 10 false FE* 0.823,5.396 1.281,5.594 0.458,0.198 10 false t1* 0.969,4.729 2.531,5.073 1.563,0.344 10 false NO.2 Fuel Sender Gauge Assembly 0.125,6.198 2.271,6.406 2.146,0.208 10 false *: for Double Tank Type 0.708,2.552 1.167,2.75 0.458,0.198 10 false S5

except 5L-E (for 3Door):
B598689E02
1.698,0.667 2.156,0.865 0.458,0.198 10 false FV 1.698,1.125 2.156,1.323 0.458,0.198 10 false FR 1.688,1.625 2.146,1.823 0.458,0.198 10 false FE 0.99,2.083 2.208,2.479 1.219,0.396 10 false Fuel Sender Gauge Assembly 0.99,1.917 1.448,2.115 0.458,0.198 10 false R51 4.708,0.563 5.167,0.76 0.458,0.198 10 false FV 4.698,1.031 5.156,1.229 0.458,0.198 10 false FR 4.688,1.521 5.146,1.719 0.458,0.198 10 false FE&B 4.417,0.552 4.875,0.75 0.458,0.198 10 false 24 4.417,1.031 4.875,1.229 0.458,0.198 10 false 27 4.458,1.521 4.917,1.719 0.458,0.198 10 false 3 5.823,1.99 6.281,2.188 0.458,0.198 10 false CPU 4.708,5.625 5.167,5.823 0.458,0.198 10 false G304 4.708,5.802 6.948,6.073 2.24,0.271 10 false Combination Meter Assembly 0.833,5.594 3.375,5.833 2.542,0.24 10 false Fuel Tank Vent Tube Sub-assembly* 2.01,0.542 2.469,0.74 0.458,0.198 10 false 1 2.01,1.542 2.469,1.74 0.458,0.198 10 false 2 2.021,1.063 2.479,1.26 0.458,0.198 10 false 3 2.375,4.333 2.833,4.531 0.458,0.198 10 false FV2 1.76,3.948 2.219,4.146 0.458,0.198 10 false 3 1.76,4.438 2.219,4.635 0.458,0.198 10 false 1 1.771,3.469 2.229,3.667 0.458,0.198 10 false 2 4.479,3.344 5,3.552 0.521,0.208 10 false 2 4.688,3.823 5.146,4.021 0.458,0.198 10 false FR* 2.344,3.354 2.802,3.552 0.458,0.198 10 false FE2 2.74,3.354 3.198,3.552 0.458,0.198 10 false 1 2.729,3.802 3.188,4 0.458,0.198 10 false 4 2.708,4.323 3.167,4.521 0.458,0.198 10 false 5 4.417,3.823 4.938,4.031 0.521,0.208 10 false 26 4.417,4.323 4.938,4.531 0.521,0.208 10 false 25 4.708,4.344 5.167,4.542 0.458,0.198 10 false L* 2.354,3.813 2.813,4.01 0.458,0.198 10 false FR2 4.688,3.365 5.146,3.563 0.458,0.198 10 false FE* 0.823,5.396 1.281,5.594 0.458,0.198 10 false t1* 0.969,4.729 2.531,5.073 1.563,0.344 10 false NO.2 Fuel Sender Gauge Assembly 0.125,6.198 2.271,6.406 2.146,0.208 10 false *: for Double Tank Type

for 5L-E:
E380757E02
0.344,5.198 2.677,5.385 2.333,0.188 10 false Fuel Tank Vent Tube Sub-assembly* 0.396,2.313 2.729,2.5 2.333,0.188 10 false Fuel Tank Vent Tube Assembly 0.344,5 2.677,5.188 2.333,0.188 10 false t1* 0.406,4.406 2.74,4.594 2.333,0.188 10 false NO.2 Fuel Sender Gauge Assembly 2.385,3.365 3.063,3.521 0.677,0.156 10 false FR2 2.417,3.958 3.094,4.115 0.677,0.156 10 false FV2 2.792,3.354 3.469,3.51 0.677,0.156 10 false 4 2.792,3.958 3.469,4.115 0.677,0.156 10 false 5 2.052,3.99 2.729,4.146 0.677,0.156 10 false 2 0.938,3.979 1.615,4.135 0.677,0.156 10 false 1 4.719,4.927 5.396,5.083 0.677,0.156 10 false ET* 4.479,4.927 5.156,5.083 0.677,0.156 10 false 5 4.688,3.958 5.365,4.115 0.677,0.156 10 false FE 4.688,3.354 5.365,3.51 0.677,0.156 10 false L 4.5,3.365 5.177,3.521 0.677,0.156 10 false 8 4.448,3.958 5.125,4.115 0.677,0.156 10 false 23 4.74,5.594 5.427,5.792 0.688,0.198 10 false G6 4.74,5.792 6.865,6.083 2.125,0.292 10 false Combination Meter Assembly 5.813,2.729 6.49,2.885 0.677,0.156 10 false CPU 4.688,4.396 5.365,4.552 0.677,0.156 10 false E2 4.427,4.406 5.104,4.563 0.677,0.156 10 false 21 0.906,1.115 1.583,1.271 0.677,0.156 10 false 2 2.073,1.125 2.75,1.281 0.677,0.156 10 false 3 2.49,0.51 3.167,0.667 0.677,0.156 10 false FS 2.802,1.115 3.479,1.271 0.677,0.156 10 false 3 2.802,0.531 3.479,0.688 0.677,0.156 10 false 2 2.479,1.115 3.156,1.271 0.677,0.156 10 false FE 0.646,1.563 2.979,1.75 2.333,0.188 10 false Fuel Sender Gauge Assembly 0.656,1.396 1.333,1.552 0.677,0.156 10 false A 4.688,0.521 5.365,0.677 0.677,0.156 10 false L 4.688,1.135 5.365,1.292 0.677,0.156 10 false E 4.479,0.51 5.156,0.667 0.677,0.156 10 false 9 4.406,1.115 5.083,1.271 0.677,0.156 10 false 24 0.208,6.406 2.542,6.594 2.333,0.188 10 false *: for Double Tank Type 0.396,2.125 1.073,2.281 0.677,0.156 10 false S5

PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTC B1500 and B1501 is not output A
DTC B1500 is output B
DTC B1501 is output C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

C

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender, Empty, Warning, 1/ 4, 1/2, 3/4, Full or Sender F -

OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except 5L-E (for Single Tank Type) A
except 5L-E (for Double Tank Type) B
for 5L-E (for Single Tank Type) C
for 5L-E (for Double Tank Type) D



A

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

7.INSPECT FUEL SENDER GAGE ASSEMBLY

C

13.INSPECT FUEL SENDER GAGE ASSEMBLY

D

16.INSPECT FUEL SENDER GAGE ASSEMBLY
4.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Result Proceed to
OK (for 5Door) A
OK (for 3Door) B
NG C



A

5.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

C

5.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
B598640C06
0.333,3.667 0.75,3.917 0.417,0.25 1.469,0.24 1.969,0.49 0.5,0.25 2.083,1.271 2.542,1.948 2.542,1.948 2.74,1.948 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 1.354,1.26 1.021,0.927 1.021,0.927 0.771,0.927 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.49,0.854 0.823,1.104 0.333,0.25 10 false FR 2.583,0.781 2.917,1.031 0.333,0.25 10 false FE 2.875,1.865 3.208,2.115 0.333,0.25 10 false FV 1.615,0.292 2.052,0.521 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Suction Plate Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-1 (FV) - A-1 Always Below 1 Ω
S5-2 (FE) - A-2 Always Below 1 Ω
S5-3 (FR) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 5Door

*2: for 3Door


a.

Disconnect the S5 fuel suction plate sub-assembly connector.*1


b.

Disconnect the R51 fuel sender gauge assembly connector.*2


c.

Disconnect the G304 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-3 (FR) - G304-27 (FR) Always Below 1 Ω
S5-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
S5-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-3 (FR) - G304-27 (FR) Always Below 1 Ω
R51-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
R51-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL SENDER GAGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

8.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY

NG

8.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY


Result:
Result Proceed to
OK (for 5Door) A
OK (for 3Door) B
NG C



A

9.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY

B

11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

C

9.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
B598640C07
0.333,3.667 0.75,3.917 0.417,0.25 1.51,0.281 2.01,0.531 0.5,0.25 2.083,1.271 2.542,1.948 2.542,1.948 2.74,1.948 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 1.354,1.26 1.021,0.927 1.021,0.927 0.771,0.927 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.49,0.854 0.823,1.104 0.333,0.25 10 false FR 2.583,0.781 2.917,1.031 0.333,0.25 10 false FE 2.875,1.865 3.208,2.115 0.333,0.25 10 false FV 1.656,0.313 2.094,0.542 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Suction Plate Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-1 (FV) - A-1 Always Below 1 Ω
S5-2 (FE) - A-2 Always Below 1 Ω
S5-3 (FR) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY

NG

10.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY
E380660C03
1.688,2.74 2.094,2.969 0.406,0.229 0.833,2.583 0.667,2.583 0.667,2.583 1.688,1.104 true 1.5,2.333 1.313,2.333 1.313,2.333 1.865,1.073 true 2.083,1.917 1.833,1.917 1.833,1.917 2.063,1.083 true 1.594,0.375 1.906,0.573 0.313,0.198 10 false *a 0.906,2.479 1.219,2.677 0.313,0.198 10 false 3 1.573,2.25 1.885,2.448 0.313,0.198 10 false 2 2.156,1.833 2.469,2.031 0.313,0.198 10 false 1 0.188,2.99 0.5,3.188 0.313,0.198 10 false *b 1.813,2.781 2.125,2.979 0.313,0.198 10 false t1
*a Fuel Tank Vent Tube Sub-assembly
*b Component without harness connected
(Fuel Tank Vent Tube Sub-asembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-1 (FE2) - 2 Always Below 1 Ω
t1-4 (FR2) - 3 Always Below 1 Ω
t1-5 (FV2) - 1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 5Door

*2: for 3Door


a.

Disconnect the S5 fuel suction plate sub-assembly connector.*1


b.

Disconnect the R51 fuel sender gauge assembly connector.*2


c.

Disconnect the G304 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-3 (FR) - G304-27 (FR) Always Below 1 Ω
S5-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
S5-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-3 (FR) - G304-27 (FR) Always Below 1 Ω
R51-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
R51-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the t1 fuel tank vent tube sub-assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - G304-26 (FR) Always Below 1 Ω
t1-1 (FE2) - G304-2 (FE) Always Below 1 Ω
t1-5 (FV2) - G304-25 (L) Always Below 1 Ω
G304-26 (FR) - Body ground Always 10 kΩ or higher
G304-2 (FE) - Body ground Always 10 kΩ or higher
G304-25 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT FUEL SENDER GAGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

14.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

14.INSPECT FUEL TANK VENT TUBE ASSEMBLY
B599359C01
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.229 1.958,0.479 0.5,0.25 1.417,1.323 0.958,1.823 0.958,1.823 0.698,1.823 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 2.583,0.781 2.917,1.031 0.333,0.25 10 false FS 0.469,1.76 0.802,2.01 0.333,0.25 10 false FE 1.625,0.281 2.063,0.51 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-2 (FS) - A-2 Always Below 1 Ω
S5-3 (FE) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the S5 fuel tank vent tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-9 (L) - S5-2 (FS) Always Below 1 Ω
G6-24 (E) - S5-3 (FE) Always Below 1 Ω
G6-21 (E2) - Body ground Always Below 1 Ω
G6-9 (L) or S5-2 (FS) - Body ground Always 10 kΩ or higher
G6-24 (E) or S5-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT FUEL SENDER GAGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

17.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

17.INSPECT NO.2 FUEL SENDER GAGE ASSEMBLY
a.

Remove the No.2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the No.2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

18.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE NO.2 FUEL SENDER GAGE ASSEMBLY

18.INSPECT FUEL TANK VENT TUBE ASSEMBLY
B599359C02
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.229 1.958,0.479 0.5,0.25 1.417,1.323 0.958,1.823 0.958,1.823 0.698,1.823 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 0.115,0.188 1.552,0.354 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 2.583,0.781 2.917,1.031 0.333,0.25 10 false FS 0.469,1.76 0.802,2.01 0.333,0.25 10 false FE 1.625,0.281 2.063,0.51 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-2 (FS) - A-2 Always Below 1 Ω
S5-3 (FE) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

19.INSPECT FUEL TANK VENT TUBE SUB-ASSEMBLY
E349680C04
1.5,2.813 1.906,3.021 0.406,0.208 1.698,1.802 1.698,0.844 false 2.094,1.802 2.094,0.833 false 0.688,4.292 0.844,4.292 0.844,4.292 1.563,3.979 false 2.75,4.313 2.594,4.313 2.594,4.313 1.802,3.979 false 0.635,0.104 0.948,0.302 0.313,0.198 10 false *a 1.656,1.844 1.813,2.042 0.156,0.198 10 false 2 2.063,1.844 2.219,2.042 0.156,0.198 10 false 1 0.948,3.021 1.26,3.219 0.313,0.198 10 false *b 0.406,4.219 0.917,4.479 0.51,0.26 10 false FV2 2.813,4.229 3.25,4.417 0.438,0.188 10 false FR2 1.646,2.833 1.865,3.073 0.219,0.24 10 false t1
*a Fuel Tank Vent Tube Sub-assembly
*b Component without harness connected
(Fuel Tank Vent Tube Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - 1 Always Below 1 Ω
t1-5 (FV2) - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPLACE FUEL TANK VENT TUBE SUB-ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the S5 fuel tank vent tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-9 (L) - S5-2 (FS) Always Below 1 Ω
G6-24 (E) - S5-3 (FE) Always Below 1 Ω
G6-21 (E2) - Body ground Always Below 1 Ω
G6-9 (L) or S5-2 (FS) - Body ground Always 10 kΩ or higher
G6-24 (E) or S5-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the t1 fuel tank vent tube sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-8 (L) - t1-4 (FR2) Always Below 1 Ω
G6-23 (FE) - t1-5 (FV2) Always Below 1 Ω
G6-5 (ET) - Body ground Always Below 1 Ω
G6-8 (L) or t1-4 (FR2) - Body ground Always 10 kΩ or higher
G6-23 (FE) or t1-5 (FV2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR