If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for JBL Made | A |
| for PIONEER Made (14 Speakers) | B |
| for PIONEER Made (12 Speakers) | C |
| for PIONEER Made (9 Speakers) | D |
A
B
C
D
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly or front No. 3 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear No. 2 speaker assembly or rear speaker set | D |
| Rear header speaker assembly | E |
| No. 1 speaker with box assembly | F |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
E
F
Disconnect the H66 stereo component amplifier assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-10 (WFR+) - J4-1 | Always | Below 1 Ω |
| H66-10 (WFR+) - Body ground | Always | 10 kΩ or higher |
| H66-9 (WFR-) - J4-2 | Always | Below 1 Ω |
| H66-9 (WFR-) - Body ground | Always | 10 kΩ or higher |
| H66-3 (WFL+) - K3-1 | Always | Below 1 Ω |
| H66-3 (WFL+) - Body ground | Always | 10 kΩ or higher |
| H66-8 (WFL-) - K3-2 | Always | Below 1 Ω |
| H66-8 (WFL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H65 stereo component amplifier assembly connector.
Disconnect the H10 and H13 front No. 2 speaker assembly connectors.
Disconnect the H21 and H22 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H65-4 (FR+) - H21-1 (TWR+) | Always | Below 1 Ω |
| H65-4 (FR+) - Body ground | Always | 10 kΩ or higher |
| H65-10 (FR-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H65-10 (FR-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H65-3 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H65-3 (FL+) - Body ground | Always | 10 kΩ or higher |
| H65-9 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H65-9 (FL-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H65 stereo component amplifier assembly connector.
Disconnect the H14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H65-8 (CTR+) - H14-2 | Always | Below 1 Ω |
| H65-8 (CTR+) - Body ground | Always | 10 kΩ or higher |
| H65-7 (CTR-) - H14-1 | Always | Below 1 Ω |
| H65-7 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 4 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 4 speaker assemblies that were disconnected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H66 stereo component amplifier assembly connector.
Disconnect the L1 and M1 rear speaker set connectors.
Disconnect the L3 and M3 rear No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-5 (RR+) - L3-1 (+TW) | Always | Below 1 Ω |
| H66-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| H66-12 (RR-) - L3-2 (-TW) | Always | Below 1 Ω |
| H66-12 (RR-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (+) - L1-1 | Always | Below 1 Ω |
| L3-3 (+) - Body ground | Always | 10 kΩ or higher |
| L3-4 (-) - L1-2 | Always | Below 1 Ω |
| L3-4 (-) - Body ground | Always | 10 kΩ or higher |
| H66-4 (RL+) - M3-1 (+TW) | Always | Below 1 Ω |
| H66-4 (RL+) - Body ground | Always | 10 kΩ or higher |
| H66-11 (RL-) - M3-2 (-TW) | Always | Below 1 Ω |
| H66-11 (RL-) - Body ground | Always | 10 kΩ or higher |
| M3-3 (+) - M1-1 | Always | Below 1 Ω |
| M3-3 (+) - Body ground | Always | 10 kΩ or higher |
| M3-4 (-) - M1-2 | Always | Below 1 Ω |
| M3-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H66 stereo component amplifier assembly connector.
Disconnect the Q15 and R13 rear header speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-2 (MR+) - Q15-2 | Always | Below 1 Ω |
| H66-2 (MR+) - Body ground | Always | 10 kΩ or higher |
| H66-7 (MR-) - Q15-1 | Always | Below 1 Ω |
| H66-7 (MR-) - Body ground | Always | 10 kΩ or higher |
| H66-1 (ML+) - R13-2 | Always | Below 1 Ω |
| H66-1 (ML+) - Body ground | Always | 10 kΩ or higher |
| H66-6 (ML-) - R13-1 | Always | Below 1 Ω |
| H66-6 (ML-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear header speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the rear header speaker assemblies that were disconnected.
When there is a possibility that either the right or left rear header speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H65 stereo component amplifier assembly connector.
Disconnect the R24 No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H65-1 (WF1+) - R24-1 (WF1+) | Always | Below 1 Ω |
| H65-1 (WF1+) - Body ground | Always | 10 kΩ or higher |
| H65-5 (WF1-) - R24-3 (WF1-) | Always | Below 1 Ω |
| H65-5 (WF1-) - Body ground | Always | 10 kΩ or higher |
| H65-2 (WF2+) - R24-2 (WF2+) | Always | Below 1 Ω |
| H65-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| H65-6 (WF2-) - R24-4 (WF2-) | Always | Below 1 Ω |
| H65-6 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL
Inspect the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly or front No. 3 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear No. 2 speaker assembly, rear header speaker assembly or rear speaker set | D |
| No. 1 speaker with box assembly | E |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
E
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-5 (WFR+) - J4-1 | Always | Below 1 Ω |
| H67-5 (WFR+) - Body ground | Always | 10 kΩ or higher |
| H67-20 (WFR-) - J4-2 | Always | Below 1 Ω |
| H67-20 (WFR-) - Body ground | Always | 10 kΩ or higher |
| H67-4 (WFL+) - K3-1 | Always | Below 1 Ω |
| H67-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| H67-19 (WFL-) - K3-2 | Always | Below 1 Ω |
| H67-19 (WFL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H10 and H13 front No. 2 speaker assembly connectors.
Disconnect the H21 and H22 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-13 (FR+) - H21-1 (TWR+) | Always | Below 1 Ω |
| H67-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| H67-28 (FR-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H67-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H67-12 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H67-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| H67-27 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H67-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-7 (CTR+) - H14-2 | Always | Below 1 Ω |
| H67-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| H67-22 (CTR-) - H14-1 | Always | Below 1 Ω |
| H67-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the L1 and M1 rear speaker set connectors.
Disconnect the L3 and M3 rear No. 2 speaker assembly connectors.
Disconnect the Q15 and R13 rear header speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-9 (RR+) - L3-1 (+TW) | Always | Below 1 Ω |
| H67-9 (RR+) - Q15-2 | Always | Below 1 Ω |
| H67-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| H67-24 (RR-) - L3-2 (-TW) | Always | Below 1 Ω |
| H67-24 (RR-) - Q15-1 | Always | Below 1 Ω |
| H67-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (+) - L1-1 | Always | Below 1 Ω |
| L3-3 (+) - Body ground | Always | 10 kΩ or higher |
| L3-4 (-) - L1-2 | Always | Below 1 Ω |
| L3-4 (-) - Body ground | Always | 10 kΩ or higher |
| H67-8 (RL+) - M3-1 (+TW) | Always | Below 1 Ω |
| H67-8 (RL+) - R13-2 | Always | Below 1 Ω |
| H67-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| H67-23 (RL-) - M3-2 (-TW) | Always | Below 1 Ω |
| H67-23 (RL-) - R13-1 | Always | Below 1 Ω |
| H67-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| M3-3 (+) - M1-1 | Always | Below 1 Ω |
| M3-3 (+) - Body ground | Always | 10 kΩ or higher |
| M3-4 (-) - M1-2 | Always | Below 1 Ω |
| M3-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear header speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL
Inspect the rear header speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the R24 No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-6 (WF1+) - R24-1 (WF1+) | Always | Below 1 Ω |
| H67-6 (WF1+) - Body ground | Always | 10 kΩ or higher |
| H67-21 (WF1-) - R24-3 (WF1-) | Always | Below 1 Ω |
| H67-21 (WF1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>REMOVAL
Inspect the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 5 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly or front No. 3 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear header speaker assembly or rear speaker set | D |
| No. 1 speaker with box assembly | E |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
E
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-5 (WFR+) - J4-1 | Always | Below 1 Ω |
| H67-5 (WFR+) - Body ground | Always | 10 kΩ or higher |
| H67-20 (WFR-) - J4-2 | Always | Below 1 Ω |
| H67-20 (WFR-) - Body ground | Always | 10 kΩ or higher |
| H67-4 (WFL+) - K3-1 | Always | Below 1 Ω |
| H67-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| H67-19 (WFL-) - K3-2 | Always | Below 1 Ω |
| H67-19 (WFL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H10 and H13 front No. 2 speaker assembly connectors.
Disconnect the H21 and H22 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-13 (FR+) - H21-1 (TWR+) | Always | Below 1 Ω |
| H67-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| H67-28 (FR-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H67-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H67-12 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H67-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| H67-27 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H67-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-7 (CTR+) - H14-2 | Always | Below 1 Ω |
| H67-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| H67-22 (CTR-) - H14-1 | Always | Below 1 Ω |
| H67-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the Q32 and R37 rear speaker set connectors.
Disconnect the Q15 and R13 rear header speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-9 (RR+) - Q32-1 | Always | Below 1 Ω |
| H67-9 (RR+) - Q15-2 | Always | Below 1 Ω |
| H67-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| H67-24 (RR-) - Q32-2 | Always | Below 1 Ω |
| H67-24 (RR-) - Q15-1 | Always | Below 1 Ω |
| H67-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| H67-8 (RL+) - R37-1 | Always | Below 1 Ω |
| H67-8 (RL+) - R13-2 | Always | Below 1 Ω |
| H67-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| H67-23 (RL-) - R37-2 | Always | Below 1 Ω |
| H67-23 (RL-) - R13-1 | Always | Below 1 Ω |
| H67-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>REMOVAL
Inspect the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear header speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>REMOVAL
Inspect the rear header speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the Q30 No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-6 (WF1+) - Q30-2 (WF1+) | Always | Below 1 Ω |
| H67-6 (WF1+) - Body ground | Always | 10 kΩ or higher |
| H67-21 (WF1-) - Q30-4 (WF1-) | Always | Below 1 Ω |
| H67-21 (WF1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>REMOVAL
Inspect the No. 1 speaker with box assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER (for 3 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly or front No. 3 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear speaker set | D |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-5 (WFR+) - J4-1 | Always | Below 1 Ω |
| H67-5 (WFR+) - Body ground | Always | 10 kΩ or higher |
| H67-20 (WFR-) - J4-2 | Always | Below 1 Ω |
| H67-20 (WFR-) - Body ground | Always | 10 kΩ or higher |
| H67-4 (WFL+) - K3-1 | Always | Below 1 Ω |
| H67-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| H67-19 (WFL-) - K3-2 | Always | Below 1 Ω |
| H67-19 (WFL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H10 and H13 front No. 2 speaker assembly connectors.
Disconnect the H21 and H22 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-13 (FR+) - H21-1 (TWR+) | Always | Below 1 Ω |
| H67-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| H67-28 (FR-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H67-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H67-12 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H67-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| H67-27 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H67-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 3 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-7 (CTR+) - H14-2 | Always | Below 1 Ω |
| H67-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| H67-22 (CTR-) - H14-1 | Always | Below 1 Ω |
| H67-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the L1 and M1 rear speaker set connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-9 (RR+) - L1-1 | Always | Below 1 Ω |
| H67-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| H67-24 (RR-) - L1-2 | Always | Below 1 Ω |
| H67-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| H67-8 (RL+) - M1-1 | Always | Below 1 Ω |
| H67-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| H67-23 (RL-) - M1-2 | Always | Below 1 Ω |
| H67-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker set.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG