Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- If the auto up/down function does not operate, the cause may be one or more of the following:
- The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
- The power window regulator switch has a malfunction.
- The Hall-IC in the power window regulator motor has a malfunction.
- There is an open or short in the wiring between the power window regulator switch and the passenger side power window regulator motor.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
B2311 is output
B
B2312 is output
C
B2313 is output
D
LIN communication system DTCs are output
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH) |
Check that the front passenger side door power window moves when the manual up/down function of the power window regulator switch is operated (Click here).
- OK:
- front passenger side door power window moves.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (FRONT POWER WINDOW REGULATOR MOTOR RH) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
P-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Door P/W Auto SW
Front passenger side power window auto up/down signal / ON or OFF
ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window switch not operated
-
- OK:
- The display changes according to operation of the power window regulator switch.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR) |
Disconnect the I3*1 or I25*2 switch connector.

- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the I4*1 or I12*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I3-8 (AUTO) - I4-4 (AUTO)
Always
Below 1 Ω
I3-8 (AUTO) or I4-4 (AUTO) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
I25-8 (AUTO) - I12-4 (AUTO)
Always
Below 1 Ω
I25-8 (AUTO) or I12-4 (AUTO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() ![]() |
Remove the power window regulator switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Switch Condition
Specified Condition
I3-8 (AUTO) - I3-1 (GND)
Auto up/down operation
Below 1 Ω
for RHD Tester Connection
Switch Condition
Specified Condition
I25-8 (AUTO) - I11-1 (GND)
Auto up/down operation
Below 1 Ω
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||

