2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
  2. The power window regulator switch has a malfunction.
  3. The Hall-IC in the power window regulator motor has a malfunction.
  4. There is an open or short in the wiring between the rear power window regulator switch RH and the power window regulator motor.

WIRING DIAGRAM

B187421E04

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result:  
    Result
    Proceed to
    DTC is not output
    A
    B2311 is output
    B
    B2312 is output
    C
    B2313 is output
    D
    LIN communication system DTCs are output
    E



B
GO TO DTC B2311 (Click here)

C
GO TO DTC B2312 (Click here)

D
GO TO DTC B2313 (Click here)

E
GO TO LIN COMMUNICATION SYSTEM (Click here)
A


2. CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
  1. Check that the manual up/down function using the rear power window regulator switch RH can operate the rear door power window RH (Click here).

    OK:
    Manual up/down function operates.



NG
OTHER PROBLEM (GO TO PROBLEM SYMPTOMS TABLE) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    RR-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear power window RH auto up/down signal / ON or OFF
    ON: Rear power window RH auto up/down switch operated
    OFF: Rear power window RH switch not operated
    -

    OK:
    The display changes according to operation of the rear power window switch RH.



NG
Go to step 4
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR RH)

  1. B184455E06
    Disconnect the J3 switch connector.

  1. Disconnect the J4 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J3-8 (AUTO) - J4-4 (AUTO)
    Always
    Below 1 Ω
    J3-8 (AUTO) or J4-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
B184456E06
  1. Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J3-8 (AUTO) - J3-1 (GND)
    Auto up/down operation
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)


← Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH (Sep 2011 – Dec 2011)All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter (Sep 2011 – Dec 2011) →