C0210/33 Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- C0215/34 Rear Speed Sensor LH Circuit
- C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH
- C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD and BA systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C0210/33 C0215/34 |
When any of the following conditions is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, the pulses are not input for 1 second. 2. A momentary interruption of the speed sensor signal occurs at least 255 times when switching the ignition switch ON and off. 3. Continuous noise occurs in the speed sensor signals at a vehicle speed of 20 km/h (12 mph) or more. 4. The speed sensor signal circuit is open for 0.12 seconds or more. |
|
| C1238/38 C1239/39 |
Noise in the speed sensor signals occurs 75 times or more for 5 seconds when the vehicle speed is 20 km/h (12 mph) or more. |
|
- HINT:
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
- DTC C0215/34 and C1239/39 are for the rear speed sensor LH.
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (RR/RL SPEED OPEN) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| RR Speed Open |
Rear speed sensor RH open detection / Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
| RL Speed Open |
Rear speed sensor LH open detection / Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
Check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
- OK:
- There are no momentary interruptions.
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED, RR/RL WHEEL DIRECTION) |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
A similar speed is indicated on the speedometer.
RL Wheel Speed
Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
A similar speed is indicated on the speedometer.
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.
Check that the sensor signal conforms to the wheel direction.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Direction
Rear wheel direction RH / Forward or Back
Forward: Forward
Back: Backward
-
RL Wheel Direction
Rear wheel direction LH / Forward or Back
Forward: Forward
Back: Backward
-
- OK:
- The wheel direction is displayed correctly.
|
|
||||
| OK | |
| 3. PERFORM SIGNAL CHECK |
Check if test mode (signal check) DTCs are output.
- HINT:
- Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Result Result
Proceed to
Test mode (signal check) DTC is output
A
Test mode (signal check) DTC is not output
B
|
|
||||
| A | |
| 4. INSPECT REAR SPEED SENSOR INSTALLATION |
Check the speed sensor installation (Click here).
- OK:
- The installation nut is tightened properly.
- There is no clearance between the sensor and rear axle.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 5. INSPECT SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning/replacement (Click here).
|
|
||||
| OK | |
| 6. INSPECT REAR SPEED SENSOR |
Install the rear speed sensor.

Disconnect the z19 and/or z20 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for RH:
Tester Connection
Switch Condition
Specified Condition
z19-2 (RR+) - Body ground
Ignition switch off
10 kΩ or higher
z19-1 (RR-) - Body ground
Ignition switch off
10 kΩ or higher
- for LH:
Tester Connection
Switch Condition
Specified Condition
z20-2 (RL+) - Body ground
Ignition switch off
10 kΩ or higher
z20-1 (RL-) - Body ground
Ignition switch off
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT SKID CONTROL SENSOR WIRE |
Disconnect the z19/z20 and Nz1 skid control sensor wire connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for RH:
Tester Connection
Condition
Specified Condition
z19-2 (RR+) - Nz1-4
Always
Below 1 Ω
z19-2 (RR+) - Nz1-3
Always
10 kΩ or higher
z19-2 (RR+) - Body ground
Always
10 kΩ or higher
z19-1 (RR-) - Nz1-3
Always
Below 1 Ω
z19-1 (RR-) - Nz1-4
Always
10 kΩ or higher
z19-1 (RR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
z20-2 (RL+) - Nz1-2
Always
Below 1 Ω
z20-2 (RL+) - Nz1-1
Always
10 kΩ or higher
z20-2 (RL+) - Body ground
Always
10 kΩ or higher
z20-1 (RL-) - Nz1-1
Always
Below 1 Ω
z20-1 (RL-) - Nz1-2
Always
10 kΩ or higher
z20-1 (RL-) - Body ground
Always
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE) |
Disconnect the A24 skid control ECU connector and Nz1 skid control sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for RH:
Tester Connection
Condition
Specified Condition
A24-5 (RR+) - Nz1-4
Always
Below 1 Ω
A24-5 (RR+) - Body ground
Always
10 kΩ or higher
A24-19 (RR-) - Nz1-3
Always
Below 1 Ω
A24-19 (RR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
A24-20 (RL+) - Nz1-2
Always
Below 1 Ω
A24-20 (RL+) - Body ground
Always
10 kΩ or higher
A24-6 (RL-) - Nz1-1
Always
Below 1 Ω
A24-6 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE) |
Reconnect the A24 skid control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for RH:
Tester Connection
Switch Condition
Specified Condition
Nz1-4 - Body ground
Ignition switch ON
7.5 to 12 V
- for LH:
Tester Connection
Switch Condition
Specified Condition
Nz1-2 - Body ground
Ignition switch ON
7.5 to 12 V
Result Result
Proceed to
OK
A
NG
LHD
B
RHD
C
|
|
||||
|
|
||||
| A | |
| 10. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTCs are output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
B
DTC is not output (When troubleshooting in accordance with the Problem Symptoms Table)
C
|
|
||||
|
|
||||
| A | |
| 11. REPLACE REAR SPEED SENSOR |
Replace the rear speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 12. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTCs are output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | |
| 13. INSPECT SPEED SENSOR ROTOR |
Remove the rear axle hub and bearing assembly (Click here).
Check the sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning/replacement (Click here).
Result Result
Proceed to
NG
A
OK
LHD
B
RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
