2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    (Click here)

  1. for Power Seat:
    (Click here)


4. REMOVE FRONT SEAT ASSEMBLY RH
  1. for Manual Seat:
    (Click here)

  1. for Power Seat:
    (Click here)

  1. for Bench Seat Type:
    (Click here)


5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


6. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)
(Click here)

7. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)
(Click here)

8. REMOVE REAR NO. 1 SEAT ASSEMBLY (for Bench Seat Type)
(Click here)

9. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


10. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B181912E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


11. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B180301E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws.

  1. Disconnect the connector and remove the instrument side panel.


12. REMOVE FRONT DOOR SCUFF PLATE LH

B181682
  1. Detach the 7 claws and 4 clips, and remove the scuff plate.


13. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


14. REMOVE COWL SIDE TRIM BOARD LH

B181911
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


15. REMOVE COWL SIDE TRIM BOARD RH

B180022
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


16. REMOVE REAR STEP COVER

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


17. REMOVE REAR DOOR SCUFF PLATE LH

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


18. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


19. REMOVE NO. 2 AIR DUCT PLUG

  1. B183335
    Detach the 4 claws and remove the 2 plugs.

    HINT:
    Use the same procedures for both sides.


20. REMOVE AIR HEATER GUIDE LH

  1. B183336
    Remove the 2 screws and guide.

    HINT:
    Use the same procedures for both sides.


21. REMOVE AIR DUCT PLUG

  1. B183333
    Detach the 2 claws and remove the plug.

    HINT:
    Use the same procedures for both sides.


22. REMOVE AIR DUCT GUIDE

  1. B183334
    Remove the screw.

  1. Detach the claw and remove the guide.

    HINT:
    Use the same procedures for both sides.


23. REMOVE REAR NO. 1 SEAT PROTECTOR

  1. B186247
    Detach the clip and 4 claws, and remove the protector.

    HINT:
    Use the same procedures to remove the protector on the other side.


24. REMOVE REAR NO. 2 SEAT PROTECTOR

  1. B184595
    Detach the clip and 4 claws, and remove the protector.

    HINT:
    Use the same procedures to remove the protector on the other side.


25. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY
  1. w/o Console Box Lid:
    (Click here)

  1. w/ Cool Box:
    (Click here)

  1. w/o Cool Box:
    (Click here)


26. REMOVE FRONT FLOOR CARPET ASSEMBLY

  1. Detach the 2 clips and 8 claws.

    B183331

  1. B183332
    Remove the carpet from the floor, open the back door and tail gate, and remove the carpet from the rear of the vehicle.


27. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Detach the 6 clips and remove the support plate.


28. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to remove the tonneau cover holder cap on the other side.

  1. Detach the 2 claws and remove the tonneau cover holder cap.


29. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190187E01

HINT:
Use the same procedure to remove the rear seat cover cap on the other side.

  1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


30. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:
When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. B181688
    Detach the 3 claws and remove the cover.

  1. B181690
    Remove the bolt and rear No. 1 seat belt anchor.

  1. B181692
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Detach the 3 claws and remove the cover.

    2. B181693
      Remove the bolt and rear No. 2 seat belt anchor.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Remove the clip and bolt.

    2. Detach the 16 clips and 2 claws.

    3. w/o Rear Air Conditioning System:
      Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

    4. w/ Rear Air Conditioning System:
      Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

      B186890

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Remove the clip.

    2. Detach the 16 clips and 2 claws, and remove the quarter trim panel.

      B190220

  1. w/ Tonneau Cover:

    1. Remove the screw and clip.

    2. Detach the 16 clips and 2 claws, and remove the quarter trim panel.

      B186438


31. REMOVE FUEL FILLER OPENING LID LOCK RETAINER

B181053
  1. Turn the cable counterclockwise and remove the cable from the retainer.

  1. B181054
    Turn the lock retainer counterclockwise and remove the lock retainer.


32. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B181065
    Detach the 2 claws.

  1. Disconnect the fuel lid lock control cable and remove the fuel lid lock open lever.


33. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. Using a screwdriver, disconnect the clamps shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.


    B181052

  1. Remove the lock control cable.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →