REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH |
for Standard:
Remove the front fender splash shield (Click here).
w/ Winch:
Remove the front fender splash shield (Click here).
| 2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH |
for Standard:
Remove the front fender splash shield (Click here).
w/ Winch:
Remove the front fender splash shield (Click here).
| 3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
for 1VD-FTV:
Remove the No. 1 engine under cover sub-assembly (Click here).
for 2UZ-FE:
Remove the No. 1 engine under cover sub-assembly (Click here).
for 1GR-FE:
Remove the No. 1 engine under cover sub-assembly (Click here).
for 3UR-FE:
Remove the No. 1 engine under cover sub-assembly (Click here).
| 4. REMOVE UPPER RADIATOR SUPPORT SEAL |
Remove the 7 clips and radiator support seal.


| 5. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Start the engine.
Turn the A/C switch on.
Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 6. DRAIN ENGINE COOLANT |
for 1VD-FTV:
Drain the engine coolant (Click here).
for 2UZ-FE:
Drain the engine coolant (Click here).
for 1GR-FE:
Drain the engine coolant (Click here).
for 3UR-FE:
Drain the engine coolant (Click here).
| 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 8. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
w/ Sliding Roof:
Remove the floor mat rear support plate (Click here).
w/o Sliding Roof:
Remove the floor mat rear support plate (Click here).
| 9. REMOVE REAR DOOR SCUFF PLATE LH |
w/ Sliding Roof:
Remove the rear door scuff plate (Click here).
w/o Sliding Roof:
Remove the rear door scuff plate (Click here).
| 10. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 11. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat) |
w/ Sliding Roof:
Remove the rear seat cover cap (Click here).
w/o Sliding Roof:
Remove the rear seat cover cap (Click here).
| 12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
w/ Sliding Roof:
Remove the front quarter trim panel (Click here).
w/o Sliding Roof:
Remove the front quarter trim panel (Click here).
| 13. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
![]() ![]() |
Using pliers, grip the claws of the clips and slide the 2 clips.
Disconnect the heater water inlet hose and heater water outlet hose.
Remove the 2 bolts.
Disconnect the air conditioner tube and accessory assembly.
- NOTICE:
- Do not use a screwdriver or similar tool to disconnect the tube.
- Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
- Do not use a screwdriver or similar tool to disconnect the tube.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
| 14. REMOVE REAR ROOF NO. 1 AIR DUCT |
![]() ![]() |
Detach the 2 claws and remove the cooler plate.
Remove the clip and duct.

| 15. REMOVE REAR COOLING UNIT ASSEMBLY |
![]() ![]() |
Disconnect the 2 connectors.
Remove the 4 bolts and rear cooling unit.



