Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P1251  Turbocharger / Supercharger Overboost Condition (Too High)  


DESCRIPTION

HINT:

Refer to DTC P0046 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P0046).

Refer to DTC P00AF (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P00AF).


P1251
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Vehicle being driven The turbo motor driver detects an overcurrent caused by the DC motor being stuck (1 trip detection logic).
·

Turbocharger sub-assembly

·

Turbo motor driver

·

Turbo motor driver power source

·

VN turbo link stuck malfunction

·

Extremely low battery voltage (P0560 stored simultaneously)

·

ECM



Related Data List
DTC No. Data List
P1251
·

MAP

·

Target Booster Pressure



If DTC P1251 is stored, the following symptoms may appear:

·

VN turbo vane stuck closed malfunction

-

Vehicle surge when driving with full load

-

Sudden lack of power due to power being limited



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION ).


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1251)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
P1251 A
P1251 and other DTCs B




A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2)

B

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2)
a.

Check the motor movement when turning the ignition switch to ON, when starting the engine and then when turning the ignition switch off.

OK:

Motor moves as shown in the illustration.



A182668E04
1.03,2.832 2.927,3.015 1.896,0.183 10 Ignition switch ON to idling 1.843,0.084 2.862,0.421 1.019,0.337 10 Idling to ignition switch off 1.148,2.479 0.873,2.914 false 0.873,2.914 0.997,2.914 false 0.852,1.367 1.453,0.226 false 1.453,0.226 1.211,1.529 false 1.453,0.226 1.736,0.226 false


OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P1251)

NG

4.INSPECT TURBO MOTOR DRIVER (POWER SOURCE CIRCUIT)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P1251)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following: Powertrain / Engine / DTC / Clear.



e.

Turn the ignition switch off.


f.

Start the engine and warm it up.


g.

Drive the vehicle.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
P1251 A
No output B




A

11.REPLACE ECM

B

END

4.INSPECT TURBO MOTOR DRIVER (POWER SOURCE CIRCUIT)

OK

5.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)

OK

6.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

OK

7.REPLACE TURBO MOTOR DRIVER (for Bank 1 and/or Bank 2)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE TURBO MOTOR DRIVER (for Bank 1 and/or Bank 2)
a.

Replace the turbo motor driver (for Bank 1 and/or Bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>TURBO MOTOR DRIVER>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P1251)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P1251)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC / Clear.



e.

Turn the ignition switch off.


f.

Start the engine and warm it up.


g.

Drive the vehicle.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result
Display (DTC Output) Proceed to
P1251 A
No output B



A

9.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2) (DC MOTOR)

B

END

9.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2) (DC MOTOR)
a.

Replace the turbocharger sub-assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine and warm it up.


e.

Run the engine with a heavy load at a mid to high engine speed.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P1251.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the time spent running the engine with a heavy load at a mid to high engine speed.




NEXT

END