32000
1.INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
Using a vernier caliper and straightedge, measure dimension A between the end of the engine and the torque converter contact surface of the drive plate.
Install the torque converter to the transmission housing.
Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A measured in the first step.
B = A + 1.00 mm (0.0394 in.) or more
36100
2.INSTALL TRANSFER ASSEMBLY
Install the transfer with the 8 bolts.
Be careful not to damage the oil seal of the transfer adapter.
Install the transfer case lower protector with the 7 bolts.
Connect the clamp of the ground cable to the transfer case lower protector.
35000
3.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
Check that the 2 straight pins are attached to the engine side.
Install the transmission with the 10 bolts.
35119A
4.INSTALL TRANSMISSION HOUSING COVER
Install the transmission housing cover with the 3 bolts.
12140
5.INSTALL OIL PAN COVER
Install the oil pan cover with the 2 bolts.
6.CONNECT WIRE HARNESS AND CONNECTOR
Connect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.
Push up the lever until the claw of the transmission wire connector makes a connection sound.
Connect the 8 harness clamps.
Connect the wire harness with the 2 bolts.
Tilt up the automatic transmission.
Connect the ground cable with the bolt.
| *A | for Type A |
| *B | for Type B |
Type A or B can be distinguished by confirming the mark on the bolt.
35104V
7.CONNECT BREATHER PLUG HOSE
Connect the 3 breather plug hoses to the wire harness.
12371
8.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator to the transmission with the 4 bolts.
51203
9.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
Install the frame crossmember to the frame with the 4 bolts and 4 nuts.
Install the engine mounting hole cover.
32907A
10.CONNECT OIL COOLER TUBE
Connect the 2 transmission oil cooler hoses as shown in the illustration.
| *a | Paint Mark |
| *b | RH Side |
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
Make sure the paint mark of each hose is facing outward.
Temporarily install the oil cooler tube to the engine with the bolts A and B. Install the bolt C and tighten it to the specified torque. Then tighten the bolts A and B to the specified torque.
32101A
11.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
Turn the crankshaft to gain access to the installation locations of the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.
First install the black colored bolt and then install the remaining 5 bolts.
Install the oil pan insulator with the 2 bolts.
12.INSTALL EXHAUST PIPE (w/ DPF)
13.INSTALL EXHAUST PIPE (w/o DPF)
37110
14.INSTALL PROPELLER SHAFT ASSEMBLY
37140
15.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
33702B
16.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
Connect the gear shifting rod to the transmission control shaft lever RH with the pin and a new clip.
17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
18.ADD AUTOMATIC TRANSMISSION FLUID
19.INSPECT SHIFT LEVER POSITION
When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.
Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
If there are problems during the above inspections, perform the adjustment using the following procedures.
Move the shift lever to N
Loosen the nut of the floor shift gear shifting rod. Then, with the lever of the floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.
20.INSPECT FOR EXHAUST GAS LEAK
51440
21.INSTALL OIL PAN PROTECTOR ASSEMBLY
Install the oil pan protector with the 4 bolts.
53784
22.INSTALL FRONT FENDER APRON TRIM PACKING C
53782
23.INSTALL FRONT FENDER APRON TRIM PACKING A
51442
24.INSTALL NO. 2 ENGINE UNDER COVER
51405A
25.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53806
26.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
27.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
28.RESET MEMORY