Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255272 AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE)  INSTALLATION  


PROCEDURE

Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C228359

Engage the splines of the input shaft and turbine runner.


b.
C228360

Engage the splines of the stator shaft and stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm and engage the splines while rotating the torque converter.



c.
C228362

Turn the torque converter assembly to engage the key of the oil pump drive gear and the slot on the torque converter assembly.


d.
C358640E01
1.333,0.802 1.063,0.146 1.063,0.146 0.885,0.146 true 2.625,0.552 2.313,0.104 2.313,0.104 2.135,0.104 true 3.031,2.031 2.948,2.031 2.948,2.031 2.875,1.604 false 1.135,2.896 1.323,2.896 1.323,2.896 1.667,1.802 true 0.646,0.031 0.865,0.25 0.219,0.219 10 false *1 1.927,0.042 2.146,0.26 0.219,0.219 10 false *1 0.906,2.823 1.125,3.042 0.219,0.219 10 false *2 3.083,1.938 3.271,2.156 0.188,0.219 10 false *2 3.135,0.323 3.323,0.542 0.188,0.219 10 false A

Using a vernier caliper and straightedge, measure dimension A between the surface of the engine that contacts the transmission and the surface of the drive plate that contacts the torque converter.

Text in Illustration
*1 Engine Surface
*2 Drive Plate Surface

NOTICE:

Make sure to deduct the thickness of the straightedge.



e.
C161370E01
2.67,1.5 2.801,1.679 0.131,0.179 10 B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is more than A measured in the first step.

Standard distance:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.


·

If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

U165098E01
1.1,3.916 1.1,4.093 false 1.102,4.28 1.102,4.457 false 5.566,3.919 5.566,4.097 false 5.567,4.283 5.567,4.461 false 5.023,3.623 5.236,3.805 0.213,0.181 10 *1 5.727,2.566 5.883,2.747 0.156,0.181 10 B 1.101,3.362 1.257,3.543 0.156,0.181 10 B 4.848,0.361 5.003,0.543 0.156,0.181 10 A 2.129,0.843 2.285,1.024 0.156,0.181 10 A 1.825,0.647 1.981,0.828 0.156,0.181 10 A 1.386,0.213 1.541,0.394 0.156,0.181 10 A 0.298,1.671 0.454,1.852 0.156,0.181 10 C 6.827,2.586 6.983,2.768 0.156,0.181 10 C 0.645,3.63 0.858,3.812 0.213,0.181 10 *1 6.137,3.609 6.350,3.791 0.213,0.181 10 *2 1.717,3.63 1.930,3.812 0.213,0.181 10 *2

a.

Install the 8 bolts and 8 harness clamp brackets.

Torque:
Bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt B : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt C, Type A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt C, Type B : 12 N*m (122 kgf*cm, 9 ft.*lbf)

Text in Illustration
*1 Type A
*2 Type B

NOTICE:

The different marks on the heads of the bolts are shown in the illustration. Check whether the bolt being used is type A or type B, and then tighten the bolt using the appropriate torque.



Hide 36179 5.INSTALL LOWER TRANSFER CASE PROTECTOR

a.

Install the lower transfer case protector with the 7 bolts.

Torque:
14 N*m (139 kgf*cm, 10 ft.*lbf)


b.

Attach the clamp of the ground cable to the lower transfer case protector.


Hide 36407 6.INSTALL TRANSFER BREATHER HOSE SUB-ASSEMBLY

a.
C228920

Attach the 3 breather hose clamps to connect the transfer breather hose to the automatic transmission breather tube.


b.

Connect the 2 breather plug hoses to the harness clamp bracket.


Hide 35000 7.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

U165096E02
2.24,2.427 2.24,3.031 2.24,3.031 1.927,3.031 false 1.667,1.271 0.438,1.26 false 0.438,2.219 0.438,0.438 0.438,0.438 0.583,0.438 false 2.688,0 2.927,0.188 0.24,0.188 10 false *1 1.708,2.885 1.938,3.073 0.229,0.188 10 false *3 0.615,0.354 0.802,0.542 0.188,0.188 10 false *2

a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.

Confirm that the 2 knock pins are on the surface of the engine block that contacts the transaxle.

Text in Illustration
*1 Torque Converter Centerpiece
*2 Knock Pin
*3 Crankshaft


c.
U164815E02
2.438,0.052 2.573,0.208 0.135,0.156 10 false A 1.313,0.042 1.448,0.198 0.135,0.156 10 false A 0.875,0.333 1.01,0.49 0.135,0.156 10 false A 0.729,1.219 0.865,1.375 0.135,0.156 10 false A 2.938,0.458 3.073,0.615 0.135,0.156 10 false A 3.135,1.354 3.271,1.51 0.135,0.156 10 false A 0.865,1.531 0.99,1.688 0.125,0.156 10 false B 1.323,1.958 1.448,2.115 0.125,0.156 10 false B 2.438,1.958 2.563,2.115 0.125,0.156 10 false B 2.906,1.531 3.031,1.688 0.125,0.156 10 false B

Keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes on the automatic transaxle assembly and install the 10 bolts shown in the illustration.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 32943 8.CONNECT TRANSMISSION OIL COOLER HOSE

C181046E03
1.667,2.042 2.333,1.417 2.333,1.417 2.625,1.417 false 1.969,2.292 2.219,2.469 0.25,0.177 10 false 45° 1.969,2.604 2.219,2.781 0.25,0.177 10 false 45° 2.677,1.344 2.948,1.563 0.271,0.219 10 false *1

a.

Connect the 2 transmission oil cooler hoses to the oil cooler tube union.

NOTICE:
·

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

·

Make sure the paint mark of each hose is facing outward.



Text in Illustration
*1 Paint Mark


Hide 9.CONNECT WIRE HARNESS AND CONNECTOR

C228921

a.

Connect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Attach the 4 connector clamps and 11 harness clamps.


c.

Install the 4 wire harness clamps.


d.

Tilt up the automatic transmission.


e.

Connect the ground cable with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



Hide 12371 10.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


b.

Install the engine mounting heat insulator with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 51203 11.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.

Install the frame crossmember to the frame with the 4 bolts and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.

Install the engine mounting hole cover.


Hide 32101A 12.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

Torque:
53 N*m (535 kgf*cm, 39 ft.*lbf)

NOTICE:

First install the black-colored bolt, and then the remaining 5 silver colored bolts.



Hide 17104 15.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 16.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 37110 21.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 22.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 33702B 23.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

a.

Connect the gear shifting rod to the transmission control shaft lever RH with the pin and a new clip.


Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 28.INSPECT SHIFT LEVER POSITION

a.

When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.


b.

Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.


c.

Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after moving the shift lever to R.

If there are problems during the above inspections, perform the adjustment using the following procedures.

i.

Move the shift lever to N


ii.
C172428E02
1.175,0.153 1.357,0.330 0.182,0.177 10 *1 1.954,0.439 1.501,0.237 1.501,0.237 1.365,0.237 false

Loosen the nut of the floor shift gear shifting rod. Then, with the lever of the floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 Lever



Hide 29.INSPECT FOR EXHAUST GAS LEAK

Hide 51440 32.INSTALL OIL PAN PROTECTOR ASSEMBLY

a.

Install the oil pan protector with the 4 bolts.

Torque:
63 N*m (642 kgf*cm, 46 ft.*lbf)


Hide 53806 35.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 36.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 37.RESET MEMORY

a.