Home › Suspension › SUSPENSION CONTROL › CONTROL VALVE ASSEMBLY
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255375 CONTROL VALVE ASSEMBLY A

SUSPENSION CONTROL  CONTROL VALVE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 48940 1.INSTALL NO. 1 HEIGHT CONTROL VALVE ASSEMBLY

C172613

a.

Install the 3 bolt cushions and 3 bolt holders to the control valve.


b.

Install the control valve with the 3 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 48996D 2.INSTALL NO. 6 HEIGHT CONTROL TUBE LH

a.

Using a union nut wrench, install the No. 6 control tube to the control valve and center cylinder.

C174943E01
1.696,0.238 2.713,0.377 1.017,0.140 10 Fulcrum Length 0.553,2.22 1.713,2.369 1.160,0.148 10 Union Nut Wrench 1.77,2.284 2.303,2.284 false 2.303,2.284 3.278,1.192 false 5.169,0.188 7.044,0.371 1.875,0.184 10 No. 6 Height Control Tube LH 5.151,0.263 4.773,0.263 false 4.773,0.263 3.846,0.835 false

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48986 3.INSTALL NO. 6 HEIGHT CONTROL TUBE

a.
C358240E01
1.521,2.354 1.646,2.354 1.646,2.354 2.115,1.625 true 1.927,2.927 1.927,2.719 1.927,2.719 2.229,2.167 true 0.635,0.573 1.885,0.813 1.25,0.24 10 false Fulcrum Length 0.365,2.281 1.51,2.51 1.146,0.229 10 true Union Nut Wrench 1.01,2.958 2.677,3.167 1.667,0.208 10 true No. 6 Height Control Tube

Using a union nut wrench, install the No. 6 control tube to the control valve and center cylinder.

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48995E 4.INSTALL NO. 5 HEIGHT CONTROL TUBE LH

a.
C174941E03
1.563,2.521 1.74,2.521 true 1.74,2.521 2.229,1.76 true 2.573,2.396 2.573,2.938 true 0.729,0.552 1.729,0.729 1,0.177 10 false Fulcrum Length 0.396,2.448 1.594,2.75 1.198,0.302 10 true Union Nut Wrench 1.135,2.958 3.313,3.146 2.177,0.188 10 true No. 5 Height Control Tube LH

Using a union nut wrench, install the No. 5 control tube to the control valve and center cylinder.

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48985 5.INSTALL NO. 5 HEIGHT CONTROL TUBE

a.

Using a union nut wrench, install the No. 5 control tube to the control valve and center cylinder.

C174940E01
1.619,0.093 2.631,0.235 1.012,0.142 10 Fulcrum Length 0.797,2.127 1.965,2.302 1.168,0.175 10 Union Nut Wrench 1.98,2.203 2.48,2.203 false 2.48,2.203 3.142,1.125 false 5.216,0.363 6.872,0.528 1.656,0.165 10 No. 5 Height Control Tube 5.144,0.422 4.892,0.422 false 4.892,0.422 4.599,1.847 false

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 48997 6.CONNECT REAR NO. 4 HEIGHT CONTROL TUBE

C174917E04
0.813,0.458 0.656,0.458 true 0.656,0.458 0.656,1.052 true 1.042,2.229 0.51,2.521 true 0.51,2.521 0.51,2.833 true 0.854,0.375 2.927,0.667 2.073,0.292 10 true Rear No. 4 Height Control Tube 0.24,2.865 2.604,3.229 2.365,0.365 10 true Height Control Valve Connector

a.

Install a new gasket to the control tube, and connect the control tube with the union bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the height control valve connector.


Hide 47373B 8.INSTALL CLAMP

a.

Install the clamp to the 3 height control tube.


Hide 17420 9.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

for 1GR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


b.

for 1UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


c.

for 3UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>3UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


d.

for 1VD-FTV:

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 17430 10.CLEAN TAILPIPE ASSEMBLY

Hide 489D5 14.INSTALL HEIGHT CONTROL UNIT INSULATOR

C172582

a.

Install the insulator to the height control unit with the 3 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 15.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.