Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  C1456  Control Pressure Sensor Zero Point High  


DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When vehicle speed is 3 km/h (2 mph) or more and stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)


C1456 When vehicle speed is 3 km/h (2 mph) or more and stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Pressure control sensor circuit

·

Master cylinder solenoid (Pressure control sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON and OFF according to brake pedal operation.




OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

NG

4.INSPECT STOP LIGHT SWITCH
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation (for LHD: See Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.RECONFIRM DTC

B

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

C

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

REPLACE MASTER CYLINDER SOLENOID

C

4.INSPECT STOP LIGHT SWITCH
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MASTER CYLINDER SOLENOID

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR