Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255455 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45203A 1.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E02
0.667,1.615 0.667,0.542 0.667,0.542 1.198,0.542 false 0.802,1.563 0.802,0.542 false 1.26,0.448 1.573,0.646 0.313,0.198 10 false *a 2.688,1.052 2.917,1.25 0.229,0.198 10 false A

Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

Text in Illustration
*a Matchmark


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Be careful not to damage the dust cover.



Hide 45026D 2.INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C179099

Install the 4 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.


HINT:

Install the steering intermediate shaft assembly from the inside of the vehicle.



b.

Install the clamp to the steering column hole cover.


Hide 45240J 3.CONNECT STEERING ACTUATOR ASSEMBLY

Hide 45810 4.INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

a.
C172653

Install the 4 nuts and steering column.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 6.INSTALL WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.
C172657

Attach the 3 claws and install the wiring harness protector and wire harness.


Hide 73900 7.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 8.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55432D 10.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

Hide 55404C 14.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

Hide 55404C 15.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

Hide 55475A 16.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55474C 17.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55403C 19.INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55449C 20.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 21.INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.
U164696

Using pliers, grip the claws of the clamp and install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.


b.
C172676

Connect the 5 connectors to the turn signal switch with spiral cable.


Hide 89235A 22.INSTALL TILT AND TELESCOPIC SWITCH

a.
C159804

Attach the claw to install the switch.


b.

Connect the switch connector.


Hide 45286B 23.INSTALL UPPER STEERING COLUMN COVER

a.
C172675

Attach the claw to install the upper steering column cover.


b.

Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.


Hide 24.INSTALL LOWER STEERING COLUMN COVER

a.
C172674

Attach the 2 claws to install the lower steering column cover.

NOTICE:

Do not damage the tilt and telescopic switch.



b.

Install the 3 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 45100 25.INSTALL STEERING WHEEL ASSEMBLY

Hide 45186 27.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 45187 28.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 29.CHECK FRONT WHEELS FACING STRAIGHT AHEAD

Hide 30.INSTALL FRONT WHEELS

Hide 31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
·

Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 32.INSPECT SRS WARNING LIGHT