Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U1002 (CAN MS BUS)  Lost Communication with Gateway Module (Main body ECU)  


DESCRIPTION

·

The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

·

When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 (CAN MS BUS) Lost communication with the gateway module (main body ECU).
·

MS bus circuit

·

Windshield wiper ECU CAN branch wire or connector*1

·

Position control ECU and switch CAN branch wire or connector*2

·

Outer mirror control ECU assembly CAN branch wire or connector*2

·

Multiplex tilt and telescopic ECU branch wire or connector*3

·

Certification ECU (smart key ECU assembly) CAN branch wire or connector*4

·

Power back door unit assembly (power back door ECU) CAN branch wire or connector*5

·

No. 2 main body ECU CAN branch wire or connector*5

·

Tire pressure warning ECU and receiver CAN branch wire or connector*6

·

Main body ECU (cowl side junction block LH) CAN main wire or connector

·

Combination meter assembly CAN main wire or connector

·

Windshield wiper ECU*1

·

Position control ECU and switch*2

·

Outer mirror control ECU assembly*2

·

Multiplex tilt and telescopic ECU*3

·

Certification ECU (smart key ECU assembly)*4

·

Power back door unit assembly (power back door ECU)*5

·

No. 2 main body ECU*5

·

Tire pressure warning ECU and receiver*6

·

Main body ECU (cowl side junction block LH)

·

Combination meter assembly

·

No. 8 junction connector

·

No. 9 junction connector

·

No. 10 junction connector

·

No. 2 CAN junction connector



*1: w/ Rain Sensor

*2: w/ Seat Memory

*3: w/ Power Tilt Power Telescopic Steering Column System

*4: w/ Entry and Start System

*5: w/ Power Back Door System

*6: w/ Tire Pressure Warning System


WIRING DIAGRAM

C311001E02
5.521,1.438 7.125,2.208 1.604,0.771 10 false Main Body ECU (Cowl Side Junction Block LH) 2.417,5.99 4.469,6.479 2.052,0.49 10 false No. 2 CAN Junction Connector 2.729,2.385 4.531,2.656 1.802,0.271 10 false No. 8 Junction Connector 2.729,2.208 3.021,2.385 0.292,0.177 10 false E73 5.854,0.385 6.417,0.594 0.563,0.208 10 false CANP 5.521,1.302 5.833,1.448 0.313,0.146 10 false E3 5.854,1.031 6.385,1.229 0.531,0.198 10 false CANN 3.833,0.385 4.031,0.552 0.198,0.167 10 false 3 3.833,0.844 4.031,1.01 0.198,0.167 10 false 14 3.073,0.385 3.313,0.573 0.24,0.188 10 false 4 2.99,0.844 3.271,1.01 0.281,0.167 10 false 15 0.167,1.448 1.958,1.865 1.792,0.417 10 false Windshield Wiper ECU*1 0.167,1.292 0.583,1.469 0.417,0.177 10 false E85 1.229,0.396 1.49,0.583 0.26,0.188 10 false 6 1.229,0.844 1.438,1.063 0.208,0.219 10 false 5 0.677,0.49 1.177,0.698 0.5,0.208 10 false CANH 0.698,0.938 1.177,1.146 0.479,0.208 10 false CANL 3.833,1.292 4.031,1.458 0.198,0.167 10 false 1 3.833,1.75 4.031,1.917 0.198,0.167 10 false 12 0.25,3.802 2.375,4.5 2.125,0.698 10 false Power Back Door Unit Assembly (Power Back Door ECU)*2 0.25,3.635 0.708,3.823 0.458,0.188 10 false L52 1.229,2.75 1.458,2.948 0.229,0.198 10 false 6 1.229,3.198 1.469,3.406 0.24,0.208 10 false 5 0.677,2.844 1.167,3.021 0.49,0.177 10 false MPX1 0.698,3.292 1.167,3.51 0.469,0.219 10 false MPX2 0.25,6.052 2.104,6.698 1.854,0.646 10 false Tire Pressure Warning ECU and Receiver*3 0.25,5.885 0.615,6.104 0.365,0.219 10 false L60 1.229,4.99 1.427,5.177 0.198,0.188 10 false 3 1.229,5.438 1.448,5.635 0.219,0.198 10 false 6 0.823,5.083 1.271,5.323 0.448,0.24 10 false CP1 0.823,5.531 1.26,5.771 0.438,0.24 10 false CN1 5.573,0.365 5.813,0.563 0.24,0.198 10 false 16 5.573,0.833 5.802,1.01 0.229,0.177 10 false 15 0.167,6.833 2.125,7.125 1.958,0.292 10 false *1: w/ Rain Sensor 0.167,7.135 2.302,7.427 2.135,0.292 10 false *2: w/ Power Back Door System 0.167,7.427 3.177,7.74 3.01,0.313 10 false *3: w/ Tire Pressure Warning System 2.896,2.844 3.24,3.052 0.344,0.208 10 false L54 2.969,2.635 3.167,2.813 0.198,0.177 10 false 1 2.896,3.302 3.229,3.49 0.333,0.188 10 false L54 2.969,3.083 3.167,3.281 0.198,0.198 10 false 2 3.865,2.844 4.188,3.063 0.323,0.219 10 false L29 3.938,2.635 4.135,2.802 0.198,0.167 10 false 1 3.865,3.302 4.188,3.49 0.323,0.188 10 false L29 3.938,3.083 4.104,3.271 0.167,0.188 10 false 2 3.865,3.75 4.198,3.958 0.333,0.208 10 false L57 3.938,3.542 4.104,3.74 0.167,0.198 10 false 1 3.865,4.208 4.229,4.427 0.365,0.219 10 false L57 3.938,3.99 4.167,4.198 0.229,0.208 10 false 2 3.865,5.073 4.229,5.323 0.365,0.25 10 false L30 3.938,4.875 4.115,5.052 0.177,0.177 10 false 1 3.865,5.542 4.219,5.76 0.354,0.219 10 false L30 3.938,5.333 4.146,5.542 0.208,0.208 10 false 2 5.573,3.646 5.823,3.854 0.25,0.208 10 false 11 5.573,4.104 5.823,4.323 0.25,0.219 10 false 12 5.854,3.75 6.365,3.99 0.51,0.24 10 false MPX+ 5.854,4.198 6.344,4.417 0.49,0.219 10 false MPX- 5.49,4.708 7.125,5.26 1.635,0.552 10 false No. 2 Main Body ECU*2 5.49,4.542 5.792,4.708 0.302,0.167 10 false L50 2.896,5.083 3.208,5.302 0.313,0.219 10 false L58 2.969,4.885 3.156,5.052 0.188,0.167 10 false 1 2.896,5.531 3.24,5.729 0.344,0.198 10 false L58 2.969,5.333 3.125,5.5 0.156,0.167 10 false 2

C311002E02
2.906,4.698 4.677,5.188 1.771,0.49 10 false No. 9 Junction Connector 2.906,4.521 3.281,4.719 0.375,0.198 10 false E76 2.906,6.333 4.927,6.667 2.021,0.333 10 false No. 10 Junction Connector 2.906,6.156 3.323,6.333 0.417,0.177 10 false E70 6.031,2.271 6.604,2.51 0.573,0.24 10 false MPX1 6.031,2.719 6.573,2.938 0.542,0.219 10 false MPX2 4.01,2.125 4.208,2.344 0.198,0.219 10 false 4 4.01,2.594 4.208,2.76 0.198,0.167 10 false 15 3.25,3.729 3.469,3.938 0.219,0.208 10 false 5 3.177,4.188 3.448,4.406 0.271,0.219 10 false 16 4.01,5.375 4.219,5.583 0.208,0.208 10 false 1 4.01,5.833 4.271,6.052 0.26,0.219 10 false 12 3.25,5.375 3.458,5.594 0.208,0.219 10 false 3 3.177,5.833 3.438,6.031 0.26,0.198 10 false 14 5.667,3.229 7.094,3.969 1.427,0.74 10 false Position Control ECU and Switch*6 5.667,3.063 6.083,3.26 0.417,0.198 10 false c27 4.01,3.719 4.25,3.927 0.24,0.208 10 false 1 4.01,4.177 4.302,4.385 0.292,0.208 10 false 12 0.281,4.75 2.76,5.135 2.479,0.385 10 false Outer Mirror Control ECU Assembly*6 0.281,4.594 0.583,4.76 0.302,0.167 10 false I24 1.417,3.76 1.625,3.958 0.208,0.198 10 false 1 1.417,4.208 1.677,4.396 0.26,0.188 10 false 21 0.854,3.854 1.354,4.063 0.5,0.208 10 false CANH 0.875,4.302 1.354,4.51 0.479,0.208 10 false CANL 0.427,6.51 2.563,6.823 2.135,0.313 10 false Combination Meter Assembly 0.427,6.344 0.729,6.51 0.302,0.167 10 false E7 1.417,5.365 1.656,5.583 0.24,0.219 10 false 1 1.417,5.833 1.656,6.021 0.24,0.188 10 false 2 0.865,5.385 1.365,5.563 0.5,0.177 10 false MPX+ 0.896,6.042 1.354,6.24 0.458,0.198 10 false MPX- 5.833,2.156 6.01,2.344 0.177,0.188 10 false 5 5.833,2.615 6.01,2.823 0.177,0.208 10 false 1 0.49,7.615 2.771,7.979 2.281,0.365 10 false *6: w/ Seat Memory 4.031,0.5 4.24,0.719 0.208,0.219 10 false 7 4.031,0.958 4.281,1.208 0.25,0.25 10 false 18 3.219,0.51 3.406,0.719 0.188,0.208 10 false 2 3.135,0.958 3.365,1.156 0.229,0.198 10 false 13 0.25,1.521 3.354,2.073 3.104,0.552 10 false Certification ECU (Smart Key ECU Assembly)*4 0.25,1.354 0.708,1.542 0.458,0.188 10 false E29 1.438,0.542 1.688,0.76 0.25,0.219 10 false 27 1.438,1 1.677,1.219 0.24,0.219 10 false 28 0.885,0.635 1.375,0.875 0.49,0.24 10 false CANH 0.906,1.094 1.375,1.313 0.469,0.219 10 false CANL 3.208,2.135 3.406,2.302 0.198,0.167 10 false 3 3.167,2.583 3.417,2.802 0.25,0.219 10 false 14 1.448,2.125 1.615,2.333 0.167,0.208 10 false 5 1.438,2.573 1.677,2.792 0.24,0.219 10 false 14 0.865,2.26 1.344,2.479 0.479,0.219 10 false CANP 0.865,2.719 1.375,2.938 0.51,0.219 10 false CANN 0.208,3.104 2.594,3.406 2.385,0.302 10 false Multiplex Tilt and Telescopic ECU*5 0.208,2.927 0.625,3.135 0.417,0.208 10 false E27 0.469,7.052 2.865,7.354 2.396,0.302 10 false *4: w/ Entry and Start System 0.469,7.323 4.927,7.615 4.458,0.292 10 false *5: w/ Power Tilt and Power Telescopic Steering Column System

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)
3.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)
a.
U165284E01
1.587,2.408 1.435,2.058 1.435,2.058 1.286,2.058 false 2.174,2.863 2.326,3.213 2.326,3.213 2.475,3.213 false 1.529,1.164 1.295,1.703 1.295,1.703 1.146,1.703 false 1.604,1.164 1.838,1.703 1.838,1.703 1.987,1.703 false 0.616,1.62 1.107,1.760 0.492,0.140 10 CANP 2.017,1.62 2.508,1.760 0.492,0.140 10 CANN 0.072,0.059 0.299,0.256 0.228,0.198 10 *a 0.072,1.941 0.299,2.138 0.228,0.198 10 *b 0.991,1.978 1.483,2.118 0.492,0.140 10 CG 2.501,3.135 2.805,3.275 0.304,0.140 10 BAT 1.607,0.175 1.800,0.324 0.193,0.149 10 E3 0.273,2.572 0.538,2.710 0.265,0.137 10 E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance Malfunction
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 54 to 69 Ω 70 Ω or higher: Open in CAN main bus line
E3-16 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
E3-15 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
E3-16 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
E3-15 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3

Result
Result Proceed to
NG
·

Open in CAN main wire


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

4.CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

B

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)

C

58.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U165364E01
2.426,1.287 2.637,1.083 2.637,1.083 2.806,1.083 false 2.426,1.443 2.596,1.627 2.596,1.627 2.765,1.627 false 2.823,1.006 3.238,1.153 0.415,0.147 10 CANH 2.782,1.55 3.197,1.696 0.415,0.147 10 CANL 0.08,0.057 0.495,0.204 0.415,0.147 10 *a 1.48,1.427 1.730,1.566 0.250,0.140 10 L29

Disconnect the L29 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L29-1 (CANH) - L29-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)



OK

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

6.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U165365E01
2.425,1.287 2.635,1.083 2.635,1.083 2.804,1.083 false 2.425,1.443 2.595,1.627 2.595,1.627 2.764,1.627 false 2.822,1.006 3.237,1.153 0.415,0.147 10 CANH 2.781,1.55 3.196,1.696 0.415,0.147 10 CANL 0.079,0.057 0.494,0.204 0.415,0.147 10 *a 1.478,1.427 1.731,1.566 0.253,0.140 10 L30

Disconnect the L30 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L30-1 (CANH) - L30-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

11.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the L29 No. 2 CAN junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U166207E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E73 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.509,2.7 2.906,2.839 0.397,0.139 10 CANL 2.652,1.836 3.073,1.975 0.420,0.139 10 CANH 2.05,2.44 2.257,2.785 2.257,2.785 2.492,2.785 false 2.054,2.217 2.387,1.908 2.387,1.908 2.628,1.908 false

Disconnect the E73 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E73-3 (CANH) - E73-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)



OK

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

NG

9.CONNECT CONNECTOR
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
U166197E01
0.447,2.262 0.711,2.398 0.264,0.136 10 E73 0.086,0.087 0.256,0.248 0.170,0.161 10 *a 2.666,2.588 3.063,2.727 0.397,0.139 10 CANL 2.731,1.959 3.151,2.098 0.420,0.139 10 CANH 2.254,2.438 2.414,2.672 2.414,2.672 2.649,2.672 false 2.258,2.215 2.466,2.031 2.466,2.031 2.707,2.031 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E73-1 (CANH) - E73-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

9.CONNECT CONNECTOR
a.

Reconnect the E73 No. 8 junction connector.



NEXT

10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)
a.
U166211E01
0.834,1.135 1.025,1.271 0.191,0.136 10 E3 0.055,0.06 0.225,0.221 0.170,0.161 10 *a 2.118,1.748 2.535,1.887 0.417,0.139 10 CANN 0.473,1.748 0.893,1.887 0.420,0.139 10 CANP 1.511,1.395 1.246,1.832 1.246,1.832 1.011,1.832 false 1.601,1.395 1.866,1.832 1.866,1.832 2.101,1.832 false

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the L29 and L30 No. 2 CAN junction connectors.



NEXT

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
a.
U166195E01
0.447,2.262 0.711,2.398 0.264,0.136 10 E70 0.086,0.087 0.256,0.248 0.170,0.161 10 *a 2.653,2.597 3.050,2.736 0.397,0.139 10 CANL 2.708,1.956 3.128,2.095 0.420,0.139 10 CANH 2.254,2.438 2.401,2.681 2.401,2.681 2.636,2.681 false 2.258,2.215 2.443,2.027 2.443,2.027 2.684,2.027 false

Disconnect the E70 No. 10 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E70-1 (CANH) - E70-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 10 Junction Connector)



OK

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

16.CONNECT CONNECTOR
13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U166196E01
0.447,2.262 0.711,2.398 0.264,0.136 10 E70 0.086,0.087 0.256,0.248 0.170,0.161 10 *a 2.514,2.733 2.911,2.872 0.397,0.139 10 CANL 2.619,1.855 3.040,1.993 0.420,0.139 10 CANH 2.028,2.438 2.262,2.817 2.262,2.817 2.497,2.817 false 2.032,2.215 2.355,1.926 2.355,1.926 2.595,1.926 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E70-3 (CANH) - E70-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 10 Junction Connector)



OK

REPLACE NO. 10 JUNCTION CONNECTOR

NG

14.CONNECT CONNECTOR
14.CONNECT CONNECTOR
a.

Reconnect the E70 No. 10 junction connector.



NEXT

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)
a.
U166210E01
2.797,1.246 2.988,1.382 0.191,0.136 10 E7 0.054,0.047 0.224,0.207 0.170,0.161 10 *a 1.534,1.736 1.931,1.875 0.397,0.139 10 MPX- 0.171,1.736 0.579,1.875 0.408,0.139 10 MPX+ 1.026,1.435 0.812,1.803 0.812,1.803 0.667,1.803 false 1.137,1.435 1.351,1.803 1.351,1.803 1.517,1.803 false

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E7-1 (MPX+) - E7-2 (MPX-) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)

16.CONNECT CONNECTOR
a.

Reconnect the E70 No. 10 junction connector.



NEXT

17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
a.
U166194E01
0.447,2.263 0.711,2.399 0.264,0.136 10 E76 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 2.692,2.628 3.089,2.767 0.397,0.139 10 CANL 2.747,1.938 3.168,2.077 0.420,0.139 10 CANH 2.247,2.44 2.44,2.713 2.44,2.713 2.675,2.713 false 2.251,2.217 2.483,2.009 2.483,2.009 2.723,2.009 false

Disconnect the E76 No. 9 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-1 (CANH) - E76-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)



OK

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
U166208E01
2.647,2.263 2.911,2.399 0.264,0.136 10 E76 0.086,0.089 0.256,0.249 0.170,0.161 10 *a 0.628,2.792 1.026,2.931 0.397,0.139 10 CANL 0.219,1.633 0.639,1.772 0.420,0.139 10 CANH 1.587,2.44 1.322,2.876 1.322,2.876 1.087,2.876 false 1.583,2.217 0.988,1.705 0.988,1.705 0.748,1.705 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-7 (CANH) - E76-18 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)
a.
U165284E01
1.587,2.408 1.435,2.058 1.435,2.058 1.286,2.058 false 2.174,2.863 2.326,3.213 2.326,3.213 2.475,3.213 false 1.529,1.164 1.295,1.703 1.295,1.703 1.146,1.703 false 1.604,1.164 1.838,1.703 1.838,1.703 1.987,1.703 false 0.616,1.62 1.107,1.760 0.492,0.140 10 CANP 2.017,1.62 2.508,1.760 0.492,0.140 10 CANN 0.072,0.059 0.299,0.256 0.228,0.198 10 *a 0.072,1.941 0.299,2.138 0.228,0.198 10 *b 0.991,1.978 1.483,2.118 0.492,0.140 10 CG 2.501,3.135 2.805,3.275 0.304,0.140 10 BAT 1.607,0.175 1.800,0.324 0.193,0.149 10 E3 0.273,2.572 0.538,2.710 0.265,0.137 10 E22

Disconnect the E70 No. 10 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 108 to 132 Ω
E3-16 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-15 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-16 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

21.CONNECT CONNECTOR
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U165333E02
2.01,1.115 2.323,0.823 2.323,0.823 2.5,0.823 false 2.01,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.542,0.74 3.052,0.948 0.51,0.208 10 false CANH 2.531,1.51 3.073,1.729 0.542,0.219 10 false CANL 2.583,3.094 3.021,3.313 0.438,0.219 10 false BAT 0.917,2.052 1.208,2.281 0.292,0.229 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.917,1.313 0.333,0.208 10 false E70 0.396,2.677 0.719,2.865 0.323,0.188 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E70-3 (CANH) - E70-14 (CANN) Ignition switch off 108 to 132 Ω
E70-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E70-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E70-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E70-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 10 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 10 JUNCTION CONNECTOR

NG

38.CONNECT CONNECTOR
21.CONNECT CONNECTOR
a.

Reconnect the E70 No. 10 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
a.
U165337E02
2.198,1.115 2.354,0.948 2.354,0.948 2.521,0.948 false 2.198,1.281 2.365,1.5 2.365,1.5 2.531,1.5 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.552,0.875 3.042,1.073 0.49,0.198 10 false CANH 2.552,1.427 3.031,1.635 0.479,0.208 10 false CANL 2.583,3.094 3.01,3.313 0.427,0.219 10 false BAT 0.917,2.052 1.229,2.313 0.313,0.26 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.917,1.323 0.333,0.219 10 false E76 0.427,2.677 0.792,2.875 0.365,0.198 10 false E22

Disconnect the E76 No. 9 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-1 (CANH) - E76-12 (CANL) Ignition switch off 108 to 132 Ω
E76-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-12 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E76-12 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)
a.
U165284E01
1.587,2.408 1.435,2.058 1.435,2.058 1.286,2.058 false 2.174,2.863 2.326,3.213 2.326,3.213 2.475,3.213 false 1.529,1.164 1.295,1.703 1.295,1.703 1.146,1.703 false 1.604,1.164 1.838,1.703 1.838,1.703 1.987,1.703 false 0.616,1.62 1.107,1.760 0.492,0.140 10 CANP 2.017,1.62 2.508,1.760 0.492,0.140 10 CANN 0.072,0.059 0.299,0.256 0.228,0.198 10 *a 0.072,1.941 0.299,2.138 0.228,0.198 10 *b 0.991,1.978 1.483,2.118 0.492,0.140 10 CG 2.501,3.135 2.805,3.275 0.304,0.140 10 BAT 1.607,0.175 1.800,0.324 0.193,0.149 10 E3 0.273,2.572 0.538,2.710 0.265,0.137 10 E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 108 to 132 Ω
E3-16 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-15 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-16 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - POSITION CONTROL ECU AND SWITCH)

NG

28.CONNECT CONNECTOR
24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - POSITION CONTROL ECU AND SWITCH)
NOTICE:

For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Multiplex Tilt and Telescopic ECU)".


a.
U165339E02
1.927,1.115 2.323,0.74 2.323,0.74 2.5,0.74 false 1.927,1.281 2.219,1.625 2.219,1.625 2.385,1.625 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.531,0.667 3.021,0.875 0.49,0.208 10 false CANH 2.417,1.542 2.906,1.781 0.49,0.24 10 false CANL 2.583,3.094 3.052,3.333 0.469,0.24 10 false BAT 0.917,2.052 1.26,2.281 0.344,0.229 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.927,1.323 0.344,0.219 10 false E76 0.427,2.677 0.76,2.875 0.333,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-4 (CANH) - E76-15 (CANL) Ignition switch off 200 Ω or higher
E76-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-4 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E76-15 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher



Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3


OK

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NG

40.CONNECT CONNECTOR
25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
NOTICE:

For vehicles without a power tilt and power telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Outer Mirror Control ECU Assembly)".


a.
U165341E02
2.01,1.115 2.323,0.823 2.323,0.823 2.5,0.823 false 2.01,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.521,0.75 3.042,0.948 0.521,0.198 10 false CANH 2.531,1.5 3.042,1.781 0.51,0.281 10 false CANL 2.604,3.094 3.073,3.344 0.469,0.25 10 false BAT 0.917,2.052 1.208,2.229 0.292,0.177 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.906,1.302 0.323,0.198 10 false E76 0.396,2.677 0.771,2.906 0.375,0.229 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-3 (CANH) - E76-14 (CANL) Ignition switch off 200 Ω or higher
E76-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E76-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher



Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3


OK

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)

NG

42.CONNECT CONNECTOR
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)
NOTICE:

For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Certification ECU)".


a.
U165340E02
1.823,1.115 2.292,0.708 2.292,0.708 2.458,0.708 false 1.823,1.281 2.167,1.667 2.167,1.667 2.333,1.667 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.5,0.635 3,0.875 0.5,0.24 10 false CANH 2.354,1.583 2.844,1.792 0.49,0.208 10 false CANL 2.583,3.094 3.052,3.323 0.469,0.229 10 false BAT 0.917,2.052 1.25,2.24 0.333,0.188 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.938,1.323 0.354,0.219 10 false E76 0.417,2.677 0.76,2.885 0.344,0.208 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-5 (CANH) - E76-16 (CANL) Ignition switch off 200 Ω or higher
E76-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-5 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E76-16 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - CERTIFICATION ECU)

NG

44.CONNECT CONNECTOR
27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - CERTIFICATION ECU)
NOTICE:

For vehicles without an entry and start system, replace No. 9 junction connector.


a.
U165338E02
2.115,1.115 2.323,0.823 2.323,0.823 2.5,0.823 false 2.115,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.521,0.75 3.031,1 0.51,0.25 10 false CANH 2.542,1.5 3.042,1.76 0.5,0.26 10 false CANL 2.583,3.094 3.052,3.313 0.469,0.219 10 false BAT 0.917,2.052 1.24,2.271 0.323,0.219 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.917,1.333 0.333,0.229 10 false E76 0.396,2.677 0.76,2.875 0.365,0.198 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E76-2 (CANH) - E76-13 (CANL) Ignition switch off 200 Ω or higher
E76-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E76-2 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E76-13 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

46.CONNECT CONNECTOR
28.CONNECT CONNECTOR
a.

Reconnect the E76 No. 9 junction connector.



NEXT

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
a.
U165366E01
2.297,1.166 2.514,1.01 2.514,1.01 2.683,1.01 false 2.297,1.288 2.419,1.463 2.419,1.463 2.588,1.463 false 2.216,2.956 2.393,3.174 2.393,3.174 2.562,3.174 false 2.7,0.933 3.115,1.079 0.415,0.147 10 CANH 2.605,1.386 3.021,1.533 0.415,0.147 10 CANL 2.579,3.097 2.994,3.243 0.415,0.147 10 BAT 0.915,2.057 1.147,2.204 0.232,0.147 10 CG 0.058,0.066 0.473,0.213 0.415,0.147 10 *a 0.058,1.828 0.473,1.974 0.415,0.147 10 *b 1.432,1.259 1.682,1.399 0.250,0.140 10 L30 0.4,2.676 0.667,2.815 0.267,0.140 10 E22 1.661,2.517 1.378,2.136 1.378,2.136 1.209,2.136 false

Disconnect the L30 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L30-1 (CANH) - L30-2 (CANL) Ignition switch off 108 to 132 Ω
L30-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
L30-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
L30-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L30-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3



OK

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
U165284E01
1.587,2.408 1.435,2.058 1.435,2.058 1.286,2.058 false 2.174,2.863 2.326,3.213 2.326,3.213 2.475,3.213 false 1.529,1.164 1.295,1.703 1.295,1.703 1.146,1.703 false 1.604,1.164 1.838,1.703 1.838,1.703 1.987,1.703 false 0.616,1.62 1.107,1.760 0.492,0.140 10 CANP 2.017,1.62 2.508,1.760 0.492,0.140 10 CANN 0.072,0.059 0.299,0.256 0.228,0.198 10 *a 0.072,1.941 0.299,2.138 0.228,0.198 10 *b 0.991,1.978 1.483,2.118 0.492,0.140 10 CG 2.501,3.135 2.805,3.275 0.304,0.140 10 BAT 1.607,0.175 1.800,0.324 0.193,0.149 10 E3 0.273,2.572 0.538,2.710 0.265,0.137 10 E22

Disconnect the L29 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 108 to 132 Ω
E3-16 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-15 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-16 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - POWER BACK DOOR ECU)

NG

34.CONNECT CONNECTOR
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - POWER BACK DOOR ECU)
NOTICE:

For vehicles without a power back door system, go to "Check for Short in CAN Bus Wires (No. 2 CAN Junction Connector - Tire Pressure Warning ECU)".


a.
U165367E01
2.301,1.17 2.475,1.016 2.475,1.016 2.644,1.016 false 2.301,1.283 2.462,1.45 2.462,1.45 2.631,1.45 false 2.216,2.956 2.393,3.174 2.393,3.174 2.562,3.174 false 2.661,0.939 3.076,1.086 0.415,0.147 10 CANH 2.648,1.373 3.064,1.520 0.415,0.147 10 CANL 2.579,3.097 2.994,3.243 0.415,0.147 10 BAT 0.915,2.057 1.147,2.204 0.232,0.147 10 CG 0.058,0.066 0.473,0.213 0.415,0.147 10 *a 0.058,1.828 0.473,1.974 0.415,0.147 10 *b 1.493,1.222 1.742,1.362 0.250,0.140 10 L54 0.4,2.676 0.667,2.815 0.267,0.140 10 E22 1.661,2.517 1.378,2.136 1.378,2.136 1.209,2.136 false

Disconnect the L54 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L54-1 (CANH) - L54-2 (CANL) Ignition switch off 200 Ω or higher
L54-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
L54-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
L54-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L54-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3



OK

32.CHECK FOR FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 2 MAIN BODY ECU)

NG

48.CONNECT CONNECTOR
32.CHECK FOR FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 2 MAIN BODY ECU)
a.
U165368E01
2.302,1.17 2.476,1.016 2.476,1.016 2.645,1.016 false 2.302,1.283 2.464,1.45 2.464,1.45 2.633,1.45 false 2.218,2.956 2.394,3.174 2.394,3.174 2.563,3.174 false 2.663,0.939 3.078,1.086 0.415,0.147 10 CANH 2.65,1.373 3.065,1.520 0.415,0.147 10 CANL 2.58,3.097 2.995,3.243 0.415,0.147 10 BAT 0.916,2.057 1.148,2.204 0.232,0.147 10 CG 0.059,0.066 0.475,0.213 0.415,0.147 10 *a 0.059,1.828 0.475,1.974 0.415,0.147 10 *b 1.494,1.222 1.744,1.362 0.250,0.140 10 L57 0.401,2.676 0.668,2.815 0.267,0.140 10 E22 1.662,2.517 1.38,2.136 1.38,2.136 1.211,2.136 false

Disconnect the L57 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L57-1 (CANH) - L57-2 (CANL) Ignition switch off 200 Ω or higher
L57-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
L57-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
L57-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L57-2 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU)

NG

50.CONNECT CONNECTOR
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU)
NOTICE:

For vehicles without a tire pressure warning system, go to "Replace No. 2 CAN Junction Connector".


a.
U165370E01
2.302,1.17 2.476,1.016 2.476,1.016 2.645,1.016 false 2.302,1.283 2.464,1.45 2.464,1.45 2.633,1.45 false 2.218,2.956 2.394,3.174 2.394,3.174 2.563,3.174 false 2.663,0.939 3.078,1.086 0.415,0.147 10 CANH 2.65,1.373 3.065,1.520 0.415,0.147 10 CANL 2.58,3.097 2.995,3.243 0.415,0.147 10 BAT 0.916,2.057 1.148,2.204 0.232,0.147 10 CG 0.059,0.066 0.475,0.213 0.415,0.147 10 *a 0.059,1.828 0.475,1.974 0.415,0.147 10 *b 1.494,1.222 1.744,1.362 0.250,0.140 10 L58 0.401,2.676 0.668,2.815 0.267,0.140 10 E22 1.662,2.517 1.38,2.136 1.38,2.136 1.211,2.136 false

Disconnect the L58 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L58-1 (CANH) - L58-2 (CANL) Ignition switch off 200 Ω or higher
L58-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
L58-2 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
L58-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L58-2 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

52.CONNECT CONNECTOR
34.CONNECT CONNECTOR
a.

Reconnect the L29 and L30 No. 2 CAN junction connectors.



NEXT

35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165334E02
2.198,1.104 2.396,0.927 2.396,0.927 2.563,0.927 false 2.208,1.292 2.406,1.479 2.406,1.479 2.573,1.479 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.604,0.833 3.104,1.083 0.5,0.25 10 false CANH 2.604,1.396 3.135,1.635 0.531,0.24 10 false CANL 2.604,3.094 3.052,3.313 0.448,0.219 10 false BAT 0.917,2.052 1.146,2.198 0.229,0.146 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 1,1.302 0.417,0.198 10 false E73 0.396,2.677 0.781,2.885 0.385,0.208 10 false E22

Disconnect the E73 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E73-1 (CANH) - E73-12 (CANL) Ignition switch off 108 to 132 Ω
E73-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-12 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E73-12 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)
*b Front view of DLC3



OK

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)
NOTICE:

For vehicles without an rain sensor, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".


a.
U165335E02
1.927,1.115 2.323,0.719 2.323,0.719 2.5,0.719 false 1.927,1.281 2.229,1.625 2.229,1.625 2.396,1.625 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.531,0.656 3.021,0.875 0.49,0.219 10 false CANH 2.417,1.563 2.958,1.781 0.542,0.219 10 false CANL 2.594,3.094 3.052,3.313 0.458,0.219 10 false BAT 0.938,2.073 1.271,2.271 0.333,0.198 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.948,1.323 0.365,0.219 10 false E73 0.396,2.677 0.75,2.906 0.354,0.229 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E73-4 (CANH) - E73-15 (CANL) Ignition switch off 200 Ω or higher
E73-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-4 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E73-15 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)
*b Front view of DLC3



OK

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

54.CONNECT CONNECTOR
37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U165336E02
2.01,1.115 2.323,0.823 2.323,0.823 2.5,0.823 false 2.01,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 2.219,2.958 2.396,3.177 2.396,3.177 2.563,3.177 false 1.667,2.521 1.375,2.135 1.375,2.135 1.208,2.135 false 2.531,0.75 3.031,0.958 0.5,0.208 10 false CANH 2.542,1.51 3,1.76 0.458,0.25 10 false CANL 2.583,3.094 3.031,3.313 0.448,0.219 10 false BAT 0.917,2.052 1.219,2.281 0.302,0.229 10 false CG 0.063,0.063 0.479,0.208 0.417,0.146 10 false *a 0.063,1.823 0.479,1.969 0.417,0.146 10 false *b 0.583,1.104 0.938,1.302 0.354,0.198 10 false E73 0.396,2.677 0.729,2.865 0.333,0.188 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E73-3 (CANH) - E73-14 (CANL) Ignition switch off 108 to 132 Ω
E73-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E73-3 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E73-14 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

56.CONNECT CONNECTOR
38.CONNECT CONNECTOR
a.

Reconnect the E70 No. 10 junction connector.



NEXT

39.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
39.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U165285E01
2.254,2.885 2.432,3.142 2.432,3.142 2.572,3.142 false 0.063,1.848 0.246,1.991 0.183,0.143 10 *b 0.063,0.051 0.246,0.195 0.183,0.143 10 *a 0.358,2.56 0.636,2.701 0.277,0.141 10 E22 1.647,2.406 1.415,2.068 1.415,2.068 1.274,2.068 false 0.99,1.989 1.267,2.129 0.277,0.141 10 CG 2.591,3.057 2.892,3.198 0.301,0.141 10 BAT 2.821,1.328 3.008,1.469 0.187,0.141 10 E7 0.999,1.332 0.854,1.203 0.854,1.203 0.742,1.203 false 0.24,1.123 0.693,1.264 0.453,0.141 10 MPX+ 1.114,1.368 0.901,1.597 0.901,1.597 0.789,1.597 false 0.287,1.517 0.740,1.658 0.453,0.141 10 MPX-

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E7-1 (MPX+) - E7-2 (MPX-) Ignition switch off 108 to 132 Ω
E7-1 (MPX+) - E22-4 (CG) Ignition switch off 200 Ω or higher
E7-2 (MPX-) - E22-4 (CG) Ignition switch off 200 Ω or higher
E7-1 (MPX+) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E7-2 (MPX-) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (MPX+, MPX-)

40.CONNECT CONNECTOR
a.

Reconnect the E76 No. 9 junction connector.



NEXT

41.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH)
41.CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH)
a.
U165290E02
2.188,2.885 2.365,3.146 2.365,3.146 2.51,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 1.469,1.052 1.323,0.927 1.323,0.927 1.208,0.927 false 1.469,1.24 1.313,1.417 1.313,1.417 1.198,1.417 false 0.063,1.844 0.458,2.042 0.396,0.198 10 false *b 0.063,0.052 0.396,0.26 0.333,0.208 10 false *a 0.406,2.563 0.802,2.729 0.396,0.167 10 false E22 0.927,1.99 1.292,2.177 0.365,0.188 10 false CG 2.552,3.052 3.031,3.25 0.479,0.198 10 false BAT 2.458,1.063 2.896,1.25 0.438,0.188 10 false c27 0.708,0.844 1.219,1.031 0.51,0.188 10 false MPX2 0.677,1.333 1.188,1.521 0.51,0.188 10 false MPX1

Disconnect the c27 position control ECU and switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
c27-5 (MPX1) - c27-1 (MPX2) Ignition switch off 54 to 69 Ω
c27-5 (MPX1) - E22-4 (CG) Ignition switch off 200 Ω or higher
c27-1 (MPX2) - E22-4 (CG) Ignition switch off 200 Ω or higher
c27-5 (MPX1) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
c27-1 (MPX2) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Position Control ECU and Switch)
*b Front view of DLC3



OK

REPLACE POSITION CONTROL ECU AND SWITCH

NG

REPLACE CAN BRANCH WIRE CONNECTED TO POSITION CONTROL ECU AND SWITCH (MPX1, MPX2)

42.CONNECT CONNECTOR
a.

Reconnect the E76 No. 9 junction connector.



NEXT

43.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
43.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U165294E02
2.198,2.885 2.375,3.146 2.375,3.146 2.521,3.146 false 1.573,2.406 1.344,2.073 1.344,2.073 1.198,2.073 false 1.698,0.979 2.229,0.365 2.229,0.365 2.344,0.365 false 1.708,1.281 2.021,1.698 2.021,1.698 2.135,1.698 false 0.063,1.844 0.354,2.063 0.292,0.219 10 false *b 0.063,0.052 0.333,0.26 0.271,0.208 10 false *a 0.385,2.563 0.74,2.75 0.354,0.188 10 false E22 0.906,1.99 1.24,2.177 0.333,0.188 10 false CG 2.583,3.063 2.969,3.24 0.385,0.177 10 false BAT 0.365,1.031 0.708,1.208 0.344,0.177 10 false E27 2.375,0.292 2.906,0.521 0.531,0.229 10 false CANP 2.167,1.615 2.708,1.823 0.542,0.208 10 false CANN

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E27-5 (CANP) - E27-14 (CANN) Ignition switch off 54 to 69 Ω
E27-5 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher
E27-14 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher
E27-5 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E27-14 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b Front view of DLC3



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)

44.CONNECT CONNECTOR
a.

Reconnect the E76 No. 9 junction connector.



NEXT

45.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
45.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
a.
U165293E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 0.583,1.042 0.823,0.479 0.823,0.479 0.938,0.479 false 0.583,1.271 0.792,1.625 0.792,1.625 0.906,1.625 false 0.063,1.844 0.438,2.063 0.375,0.219 10 false *b 0.063,0.052 0.427,0.24 0.365,0.188 10 false *a 0.385,2.563 0.76,2.74 0.375,0.177 10 false E22 0.875,1.99 1.26,2.188 0.385,0.198 10 false CG 2.552,3.052 3.104,3.281 0.552,0.229 10 false BAT 1.76,0.396 2.104,0.594 0.344,0.198 10 false I24 0.99,0.396 1.552,0.583 0.563,0.188 10 false CANH 0.948,1.542 1.448,1.75 0.5,0.208 10 false CANL

Disconnect the I24 outer mirror control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I24-1 (CANH) - I24-21 (CANL) Ignition switch off 54 to 69 Ω
I24-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
I24-21 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
I24-1 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
I24-21 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)
*b Front view of DLC3



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CANH, CANL)

46.CONNECT CONNECTOR
a.

Reconnect the E76 No. 9 junction connector.



NEXT

47.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
47.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
a.
U165288E02
2.208,2.885 2.385,3.146 2.385,3.146 2.531,3.146 false 1.594,2.406 1.365,2.073 1.365,2.073 1.219,2.073 false 1.563,1.219 1.771,1.552 1.771,1.552 1.885,1.552 false 1.458,1.219 1.25,1.552 1.25,1.552 1.135,1.552 false 0.063,1.844 0.25,1.99 0.188,0.146 10 false *b 0.063,0.052 0.25,0.198 0.188,0.146 10 false *a 0.354,2.563 0.719,2.781 0.365,0.219 10 false E22 0.99,1.99 1.333,2.219 0.344,0.229 10 false CG 2.594,3.063 2.99,3.302 0.396,0.24 10 false BAT 1.521,0.323 1.875,0.521 0.354,0.198 10 false E29 0.615,1.469 1.104,1.708 0.49,0.24 10 false CANH 1.917,1.469 2.438,1.688 0.521,0.219 10 false CANL

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E29-27 (CANH) - E29-28 (CANL) Ignition switch off 54 to 69 Ω
E29-27 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E29-28 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E29-27 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E29-28 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

48.CONNECT CONNECTOR
a.

Reconnect the L29, L30 and L54 No. 2 CAN junction connectors.



NEXT

49.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)
49.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)
a.
U164992E01
0.108,0.08 0.361,0.219 0.253,0.139 10 *a 0.796,1.475 1.208,1.613 0.413,0.139 10 MPX1 1.005,2.093 1.418,2.232 0.413,0.139 10 CG 2.412,1.467 2.825,1.605 0.413,0.139 10 MPX2 0.108,1.997 0.361,2.236 0.253,0.239 10 *b 1.296,1.55 1.479,1.55 1.479,1.55 1.748,0.99 false 1.827,0.99 2.205,1.544 2.205,1.544 2.392,1.544 false 0.423,0.897 0.679,1.035 0.257,0.139 10 L52 0.441,2.661 0.708,2.800 0.267,0.139 10 E22 1.293,2.173 1.446,2.173 1.446,2.173 1.665,2.525 false 2.233,2.978 2.387,3.184 2.387,3.184 2.507,3.184 false 2.523,3.111 2.936,3.250 0.413,0.139 10 BAT

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) Ignition switch off 54 to 69 Ω
L52-6 (MPX1) - E22-4 (CG) Ignition switch off 200 Ω or higher
L52-5 (MPX2) - E22-4 (CG) Ignition switch off 200 Ω or higher
L52-6 (MPX1) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L52-5 (MPX2) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])
*b Front view of DLC3



OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (MPX1, MPX2)

50.CONNECT CONNECTOR
a.

Reconnect the L29, L30, L54 and L57 No. 2 CAN junction connectors.



NEXT

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 MAIN BODY ECU)
51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 MAIN BODY ECU)
a.
U164994E01
0.108,0.08 0.361,0.219 0.253,0.139 10 *a 0.194,1.118 0.607,1.257 0.413,0.139 10 MPX- 1.005,2.093 1.418,2.232 0.413,0.139 10 CG 0.108,1.997 0.361,2.236 0.253,0.239 10 *b 0.695,1.193 0.877,1.193 0.877,1.193 1.065,0.951 false 2.79,0.897 3.047,1.035 0.257,0.139 10 L50 0.441,2.661 0.708,2.800 0.267,0.139 10 E22 1.293,2.173 1.446,2.173 1.446,2.173 1.665,2.525 false 2.233,2.978 2.387,3.184 2.387,3.184 2.507,3.184 false 2.523,3.111 2.936,3.250 0.413,0.139 10 BAT 0.426,1.447 0.839,1.585 0.413,0.139 10 MPX+ 0.927,1.528 1.109,1.528 1.109,1.528 1.224,0.951 false

Disconnect the L50 No. 2 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L50-11 (MPX+) - L50-12 (MPX-) Ignition switch off 54 to 69 Ω
L50-11 (MPX+) - E22-4 (CG) Ignition switch off 200 Ω or higher
L50-12 (MPX-) - E22-4 (CG) Ignition switch off 200 Ω or higher
L50-11 (MPX+) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L50-12 (MPX-) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Main Body ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NO. 2 MAIN BODY ECU (MPX+, MPX-)

52.CONNECT CONNECTOR
a.

Reconnect the L29, L30, L54, L57 and L58 No. 2 CAN junction connectors.



NEXT

53.CHECK FOR SHORT IN CAN BUS WIRES (TIRE PRESSURE WARNING ECU)
53.CHECK FOR SHORT IN CAN BUS WIRES (TIRE PRESSURE WARNING ECU)
a.
U165409E01
0.552,1.586 0.963,1.722 0.411,0.137 10 CN1 0.463,0.595 0.868,0.731 0.405,0.137 10 CP1 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 1.658,0.325 1.914,0.462 0.256,0.137 10 L60 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 0.42,2.609 0.690,2.746 0.270,0.137 10 E22 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 0.964,2.026 1.353,2.163 0.389,0.137 10 CG 1.647,2.475 1.437,2.101 1.437,2.101 1.282,2.101 false 1.254,1.305 1.08,1.671 1.08,1.671 0.925,1.671 false 1.254,0.952 0.985,0.671 0.985,0.671 0.83,0.671 false

Disconnect the L60 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L60-3 (CP1) - L60-6 (CN1) Ignition switch off 54 to 69 Ω
L60-3 (CP1) - E22-4 (CG) Ignition switch off 200 Ω or higher
L60-6 (CN1) - E22-4 (CG) Ignition switch off 200 Ω or higher
L60-3 (CP1) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
L60-6 (CN1) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
*b Front view of DLC3



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO TIRE PRESSURE WARNING ECU (CP1, CN1)

54.CONNECT CONNECTOR
a.

Reconnect the E73 No. 8 junction connector.



NEXT

55.CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)
55.CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)
a.
U165286E02
2.177,2.875 2.354,3.135 2.354,3.135 2.5,3.135 false 1.583,2.406 1.354,2.073 1.354,2.073 1.208,2.073 false 2.104,1.073 2.25,0.938 2.25,0.938 2.396,0.938 false 1.969,1.177 2.24,1.417 2.24,1.417 2.396,1.417 false 0.063,1.844 0.385,2.063 0.323,0.219 10 false *b 0.063,0.052 0.5,0.271 0.438,0.219 10 false *a 0.396,2.563 0.792,2.74 0.396,0.177 10 false E22 0.896,1.99 1.271,2.198 0.375,0.208 10 false CG 2.542,3.052 3.094,3.25 0.552,0.198 10 false BAT 0.729,1.146 1.115,1.333 0.385,0.188 10 false E85 2.438,1.344 3,1.552 0.563,0.208 10 false CANL 2.438,0.865 3.01,1.052 0.573,0.188 10 false CANH

Disconnect the E85 windshield wiper ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E85-6 (CANH) - E85-5 (CANL) Ignition switch off 54 to 69 Ω
E85-6 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E85-5 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher
E85-6 (CANH) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E85-5 (CANL) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Windshield Wiper ECU)
*b Front view of DLC3



OK

REPLACE WINDSHIELD WIPER ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER ECU (CANH, CANL)

56.CONNECT CONNECTOR
a.

Reconnect the E73 No. 8 junction connector.



NEXT

57.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
57.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U165295E02
2.177,2.885 2.354,3.146 2.354,3.146 2.5,3.146 false 1.604,2.406 1.375,2.073 1.375,2.073 1.229,2.073 false 1.458,1.229 1.313,1.104 1.313,1.104 1.198,1.104 false 1.552,1.281 1.344,1.51 1.344,1.51 1.229,1.51 false 0.063,1.844 0.25,1.99 0.188,0.146 10 false *b 0.063,0.052 0.25,0.198 0.188,0.146 10 false *a 0.385,2.563 0.74,2.781 0.354,0.219 10 false E22 0.958,1.99 1.302,2.198 0.344,0.208 10 false CG 2.552,3.052 2.969,3.281 0.417,0.229 10 false BAT 2.479,1.021 2.781,1.229 0.302,0.208 10 false E3 0.698,1.021 1.188,1.24 0.49,0.219 10 false CANP 0.729,1.438 1.26,1.656 0.531,0.219 10 false CANN

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) Ignition switch off 108 to 132 Ω
E3-16 (CANP) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-15 (CANN) - E22-4 (CG) Ignition switch off 200 Ω or higher
E3-16 (CANP) - E22-16 (BAT) Ignition switch off 6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

58.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U165296E01
3.902,1.198 4.047,1.497 4.047,1.497 4.161,1.497 false 0.047,0.042 0.229,0.185 0.183,0.143 10 *a 4.885,0.042 5.067,0.185 0.183,0.143 10 *b 4.177,1.427 4.593,1.568 0.416,0.141 10 GND2 1.319,0.289 1.506,0.430 0.187,0.141 10 2A 1.23,1.223 1.057,1.409 1.057,1.409 0.965,1.409 false 0.556,1.344 1.009,1.485 0.453,0.141 10 ALTB 3.348,0.382 3.545,0.523 0.196,0.141 10 2D 5.517,0.21 5.705,0.350 0.187,0.141 10 E3 5.8,0.943 5.952,0.813 5.952,0.813 6.067,0.813 false 6.082,0.744 6.498,0.885 0.416,0.141 10 GND3

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-62 (GND2) - Body ground Always Below 1 Ω
E3-1 (GND3) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 (ALTB) - Body ground Always 11 to 14 V




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR