If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
When the battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
When the entry cancel function has been canceled through the customized parameters, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
If the room oscillator does not recognize the key, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.
| Problem Symptom | Data List Item |
|---|---|
| Operating Engine Switch / Key RF Signal Interference | When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1). If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG Relay Monitor(Inside) ·
IG Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor |
- |
Refer to "System Diagram" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>SYSTEM DIAGRAM)
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).
Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or ID code box (immobiliser code ECU), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
Press a switch of the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly LED illuminates.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Key Low Battery | Transmitter battery depleted/No or Yes | No: Transmitter battery not depleted
Yes: Transmitter battery depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
Press the engine switch with the brake pedal released and check that the power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Remove the transmitter battery from the electrical key transmitter sub-assembly.
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.
The power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| The power source mode does not change | A |
| The power source mode changes | B |
A
B
Using the GTS, check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and start system (for Start Function) DTCs are output | B |
A
B
OK
NG
OK
NG
Disconnect the E128 and E130 certification ECU (smart key ECU assembly) connectors.
Disconnect the 2I and 2J cowl side junction block LH connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E130-9 (ACCD) - 2J-18 | Always | Below 1 Ω |
| E128-3 (IG1D) - 2I-18 | ||
| 2J-1 - Body ground | ||
| E130-9 (ACCD) or 2J-18 - Body ground | 10 kΩ or higher | |
| E128-3 (IG1D) or 2I-18 - Body ground |
OK
NG
Remove the cowl side junction block LH.
for LHD: See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL.
for RHD: See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL.
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Cowl Side Junction Block LH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2G-1 - 2I-29 | Battery voltage applied to terminals 2I-18 and 2J-1 | Below 1 Ω |
| Battery voltage not applied to terminals 2I-18 and 2J-1 | 10 kΩ or higher | |
| 2G-1 - 2I-33 | Battery voltage applied to terminals 2I-18 and 2J-1 | Below 1 Ω |
| Battery voltage not applied to terminals 2I-18 and 2J-1 | 10 kΩ or higher | |
| 2G-1 - 2I-11 | Battery voltage applied to terminals 2I-18 and 2J-1 | Below 1 Ω |
| Battery voltage not applied to terminals 2I-18 and 2J-1 | 10 kΩ or higher | |
| 2G-1 - 2I-51 | Battery voltage applied to terminals 2J-18 and 2J-1 | Below 1 Ω |
| Battery voltage not applied to terminals 2J-18 and 2J-1 | 10 kΩ or higher |
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for LHD | B |
| for RHD | C | |
A
B
C
Install the cowl side junction block LH.
for LHD: See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL.
for RHD: See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL.
Connect the E128 and E130 certification ECU (smart key ECU assembly) connectors.
Measure the voltage while checking the Data List on the GTS.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | Power supply state/ST ON, All OFF, IG ON or ACC ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-3 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | ||
| Engine switch on (IG) | 9 V or higher | |
| E130-9 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (IG) | 8.5 V or higher | |
| Engine switch on (ACC) |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Switch1 | Engine switch 1 status/ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status/ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
The GTS display changes correctly in response to the engine switch operation.
OK
NG
Inspect the transmitter battery.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
OK
NG
Remove the engine switch).
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>ENGINE SWITCH>REMOVAL.
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (STARTING)>ENGINE SWITCH>REMOVAL.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>ENGINE SWITCH>REMOVAL.
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>ENGINE SWITCH>REMOVAL.
Inspect the engine switch.
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>ENGINE SWITCH>INSPECTION.
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (STARTING)>ENGINE SWITCH>INSPECTION.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>ENGINE SWITCH>INSPECTION.
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>ENGINE SWITCH>INSPECTION.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for 1UR-FE | B |
| for 1GR-FE | C | |
| for 3UR-FE | D | |
| for 1VD-FTV | E | |
A
B
C
D
E
Disconnect the E130 connector from the certification ECU (smart key ECU assembly).
Disconnect the E123 connector from the engine switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E130-16 (SSW1) - E123-5 (SS1) | Always | Below 1 Ω |
| E130-18 (SSW2) - E123-1 (SS2) | ||
| E130-16 (SSW1) or E123-5 (SS1) - Body ground | 10 kΩ or higher | |
| E130-18 (SSW2) or E123-1 (SS2) - Body ground |
OK
NG