Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnet clutch assembly on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the magnet clutch relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM

w/ Rear Heater:


E334387E07
5.51,0.896 5.969,1.094 0.458,0.198 10 false ACT 5.521,1.615 5.979,1.813 0.458,0.198 10 false AC1 5.531,2.542 5.99,2.74 0.458,0.198 10 false MGC 5.208,0.896 5.667,1.094 0.458,0.198 10 false 22 5.208,1.615 5.667,1.813 0.458,0.198 10 false 11 5.208,2.542 5.667,2.74 0.458,0.198 10 false 18 4.271,2.542 4.729,2.74 0.458,0.198 10 false 2 4.271,3.052 4.729,3.25 0.458,0.198 10 false 3 3.323,2.542 3.781,2.74 0.458,0.198 10 false 1 3.333,3.052 3.792,3.25 0.458,0.198 10 false 5 1.979,2.802 2.792,3 0.813,0.198 10 false A/C COMP 0.542,2.646 1.604,2.885 1.063,0.24 10 false from IG1 Relay 5.458,4.802 5.917,5 0.458,0.198 10 false E36 5.448,4.969 7,5.333 1.552,0.365 10 false Air Conditioning Amplifier Assembly 3.594,3.5 4.406,3.698 0.813,0.198 10 false MG CLT 1.906,4.052 2.365,4.25 0.458,0.198 10 false MG+ 1.302,4.052 1.76,4.25 0.458,0.198 10 false 1 1.292,4.271 2.24,4.656 0.948,0.385 10 false Magnet Clutch Assembly 3.146,4.302 3.885,4.521 0.74,0.219 10 false *1: for LHD 0.458,5.448 2.052,5.635 1.594,0.188 10 false : CAN Communication Line 0.75,2.167 1.667,2.365 0.917,0.198 10 false A38*1, A52*2 0.76,2.354 1.333,2.573 0.573,0.219 10 false ECM 1.292,1.01 1.75,1.208 0.458,0.198 10 false ACT 1.313,1.729 1.771,1.927 0.458,0.198 10 false AC1 1.76,0.896 2.938,1.115 1.177,0.219 10 false 18*3, 17* 4*, 17*5 1.74,1.615 2.74,1.813 1,0.198 10 false 30*3, 19*4, 9*5 2.292,4.042 2.75,4.24 0.458,0.198 10 false 3 0.594,4.906 0.906,5.094 0.313,0.188 10 false C30 0.604,5.073 2.479,5.292 1.875,0.219 10 false Cooler Compressor Assembly 3.156,4.573 3.896,4.792 0.74,0.219 10 false *2: for RHD 3.156,4.854 4.208,5.094 1.052,0.24 10 false *3: for 1VD-FTV 3.156,5.146 4.729,5.365 1.573,0.219 10 false *4: for 1GR-FE, 1UR-FE 3.146,5.448 4.167,5.667 1.021,0.219 10 false *5: for 3UR-FE


w/o Rear Heater:


E334387E08
5.51,0.896 5.969,1.094 0.458,0.198 10 false ACT 5.521,1.615 5.979,1.813 0.458,0.198 10 false AC1 5.531,2.542 5.99,2.74 0.458,0.198 10 false MGC 5.208,0.896 5.667,1.094 0.458,0.198 10 false 27 5.208,1.615 5.667,1.813 0.458,0.198 10 false 23 5.208,2.542 5.667,2.74 0.458,0.198 10 false 20 4.271,2.542 4.729,2.74 0.458,0.198 10 false 2 4.271,3.052 4.729,3.25 0.458,0.198 10 false 3 3.323,2.542 3.781,2.74 0.458,0.198 10 false 1 3.333,3.052 3.792,3.25 0.458,0.198 10 false 5 1.979,2.802 2.792,3 0.813,0.198 10 false A/C COMP 0.521,2.635 1.5,2.865 0.979,0.229 10 false from IG1 Relay 5.458,4.802 5.917,5 0.458,0.198 10 false E81 5.448,4.979 7.042,5.333 1.594,0.354 10 false Air Conditioning Amplifier Assembly 3.594,3.5 4.406,3.698 0.813,0.198 10 false MG CLT 1.906,4.052 2.365,4.25 0.458,0.198 10 false MG+ 1.302,4.052 1.76,4.25 0.458,0.198 10 false 1 1.292,4.271 2.219,4.635 0.927,0.365 10 false Magnet Clutch Assembly 0.573,4.896 0.896,5.083 0.323,0.188 10 false C30 0.438,5.469 2.177,5.656 1.74,0.188 10 false : CAN Communication Line 0.74,2.167 1.698,2.365 0.958,0.198 10 false A38*1, A52*2 0.75,2.333 1.167,2.542 0.417,0.208 10 false ECM 1.292,1.01 1.75,1.208 0.458,0.198 10 false ACT 1.313,1.729 1.771,1.927 0.458,0.198 10 false AC1 1.729,0.896 2.844,1.094 1.115,0.198 10 false 18*3, 17* 4, 17*5 1.74,1.615 2.813,1.833 1.073,0.219 10 false 30*3, 19*4, 9*5 2.281,4.042 2.74,4.24 0.458,0.198 10 false 3 0.573,5.063 2.469,5.271 1.896,0.208 10 false Cooler Compressor Assembly 3.177,4.281 3.938,4.479 0.76,0.198 10 false *1: for LHD 3.188,4.573 3.948,4.771 0.76,0.198 10 false *2: for RHD 3.188,4.854 4.229,5.052 1.042,0.198 10 false *3: for 1VD-FTV 3.188,5.135 4.75,5.344 1.563,0.208 10 false *4: for 1GR-FE, 1UR-FE 3.177,5.417 4.156,5.635 0.979,0.219 10 false *5: for 3UR-FE


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Since the air conditioning system has functions that use CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.READ VALUE USING GTS (A/C SWITCH SIGNAL)
a.

Use the Data List to check if the A/C switch is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Signal A/C switch signal / ON or OFF ON: A/C switch on
OFF: A/C switch off
-

OK:

The display is as specified in the normal condition.




OK

2.INSPECT MAGNET CLUTCH RELAY (MG CLT)

NG

10.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER ASSEMBLY)
2.INSPECT MAGNET CLUTCH RELAY (MG CLT)
a.

Remove the MG CLT relay from the No. 1 engine room relay block.




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)
a.
U156773E03
0.927,0.771 1.156,0.771 1.156,0.771 1.344,1.292 false 0.104,0.104 0.323,0.271 0.219,0.167 10 false *a 0.563,0.708 0.938,0.875 0.375,0.167 10 false MGC 0.604,1.208 0.979,1.375 0.375,0.167 10 false E36

w/ Rear Heater:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-18 (MGC) - Body ground Ignition switch off Below 1 V
E36-18 (MGC) - Body ground Ignition switch ON 11 to 14 V




b.
U166515E01
0.045,0.027 0.356,0.272 0.311,0.245 10 *a 1.589,0.411 1.900,0.657 0.311,0.245 10 E81 0.056,0.821 0.443,1.067 0.387,0.245 10 MGC 0.497,0.907 0.71,0.907 0.71,0.907 0.793,1.357 false

w/o Rear Heater:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-20 (MGC) - Body ground Ignition switch off Below 1 V
E81-20 (MGC) - Body ground Ignition switch ON 11 to 14 V




Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U156664E01
0.039,0.028 0.300,0.221 0.261,0.193 10 *a 1.375,0.173 1.738,0.366 0.363,0.193 10 E36 0.191,0.221 0.554,0.415 0.363,0.193 10 MGC 1.107,1.063 0.895,0.311 0.895,0.311 0.633,0.311 false

w/ Rear Heater:

i.

Reconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-18 (MGC) - Body ground
·

Engine idling

·

A/C switch off

·

Blower switch LO


11 to 14 V
E36-18 (MGC) - Body ground
·

Engine idling

·

A/C switch on

·

Blower switch LO


Below 1 V




b.
U166469E01
0.04,0.054 0.248,0.279 0.208,0.225 10 *a 1.559,0.249 1.835,0.391 0.276,0.142 10 E81 0.949,1.129 0.745,0.711 0.745,0.711 0.528,0.711 false 0.093,0.622 0.524,0.798 0.431,0.176 10 MGC

w/ Rear Heater:

i.

Reconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-20 (MGC) - Body ground
·

Engine idling

·

A/C switch off

·

Blower switch LO


11 to 14 V
E81-20 (MGC) - Body ground
·

Engine idling

·

A/C switch on

·

Blower switch LO


Below 1 V




Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


OK

5.CHECK COOLER COMPRESSOR ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER ASSEMBLY)
5.CHECK COOLER COMPRESSOR ASSEMBLY
a.

Disconnect the C30 cooler compressor assembly connector.


b.

Disconnect the magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-3 (MG+) - 1 Always Below 1 Ω
C30-3 (MG+) or 1 -Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for 1VD-FTV) B
NG (for 1GR-FE) C
NG (for 1UR-FE) D
NG (for 3UR-FE) E



A

6.INSPECT MAGNET CLUTCH ASSEMBLY

B

C

D

E

6.INSPECT MAGNET CLUTCH ASSEMBLY

A

7.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - BATTERY)

B

C

D

E

7.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - BATTERY)
a.

Remove the MG CLT relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay block MG CLT relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
Relay block MG CLT relay terminal 1 - Body ground Ignition switch ON 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER ASSEMBLY)

*1: for LHD

*2: for RHD


a.

w/ Rear Heater:

i.

Disconnect the A38*1 or A52*2 ECM connector.


ii.

Disconnect the E36 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-18 (ACT) - E36-22 (ACT)*1 Always Below 1 Ω
A38-30 (AC1) - E36-11 (AC1)*1 Always Below 1 Ω
A52-18 (ACT) - E36-22 (ACT)*2 Always Below 1 Ω
A52-30 (AC1) - E36-11 (AC1)*2 Always Below 1 Ω
A38-18 (ACT) or E36-22 (ACT) - Body ground*1 Always 10 kΩ or higher
A38-30 (AC1) or E36-11 (AC1) - Body ground*1 Always 10 kΩ or higher
A52-18 (ACT) or E36-22 (ACT) - Body ground*2 Always 10 kΩ or higher
A52-30 (AC1) or E36-11 (AC1) - Body ground*2 Always 10 kΩ or higher

for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E36-22 (ACT)*1 Always Below 1 Ω
A38-19 (AC1) - E36-11 (AC1)*1 Always Below 1 Ω
A52-17 (ACT) - E36-22 (ACT)*2 Always Below 1 Ω
A52-19 (AC1) - E36-11 (AC1)*2 Always Below 1 Ω
A38-17 (ACT) or E36-22 (ACT) - Body ground*1 Always 10 kΩ or higher
A38-19 (AC1) or E36-11 (AC1) - Body ground*1 Always 10 kΩ or higher
A52-17 (ACT) or E36-22 (ACT) - Body ground*2 Always 10 kΩ or higher
A52-19 (AC1) or E36-11 (AC1) - Body ground*2 Always 10 kΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E36-22 (ACT) Always Below 1 Ω
A38-9 (AC1) - E36-11 (AC1) Always Below 1 Ω
A38-17 (ACT) or E36-22 (ACT) - Body ground Always 10 kΩ or higher
A38-9 (AC1) or E36-11 (AC1) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the A38*1 or A52*2 ECM connector.


ii.

Disconnect the E81 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-18 (ACT) - E81-27 (ACT)*1 Always Below 1 Ω
A38-30 (AC1) - E81-23 (AC1)*1 Always Below 1 Ω
A52-18 (ACT) - E81-27 (ACT)*2 Always Below 1 Ω
A52-30 (AC1) - E81-23 (AC1)*2 Always Below 1 Ω
A38-18 (ACT) or E81-27 (ACT) - Body ground*1 Always 10 kΩ or higher
A38-30 (AC1) or E81-23 (AC1) - Body ground*1 Always 10 kΩ or higher
A52-18 (ACT) or E81-27 (ACT) - Body ground*2 Always 10 kΩ or higher
A52-30 (AC1) or E81-23 (AC1) - Body ground*2 Always 10 kΩ or higher

for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E81-27 (ACT)*1 Always Below 1 Ω
A38-19 (AC1) - E81-23 (AC1)*1 Always Below 1 Ω
A52-17 (ACT) - E81-27 (ACT)*2 Always Below 1 Ω
A52-19 (AC1) - E81-23 (AC1)*2 Always Below 1 Ω
A38-17 (ACT) or E81-27 (ACT) - Body ground*1 Always 10 kΩ or higher
A38-19 (AC1) or E81-23 (AC1) - Body ground*1 Always 10 kΩ or higher
A52-17 (ACT) or E81-27 (ACT) - Body ground*2 Always 10 kΩ or higher
A52-19 (AC1) or E81-23 (AC1) - Body ground*2 Always 10 kΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E81-27 (ACT) Always Below 1 Ω
A38-9 (AC1) - E81-23 (AC1) Always Below 1 Ω
A38-17 (ACT) or E81-27 (ACT) - Body ground Always 10 kΩ or higher
A38-9 (AC1) or E81-23 (AC1) - Body ground Always 10 kΩ or higher





OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U156665E01
0.039,0.028 0.300,0.221 0.261,0.193 10 *a 1.375,0.173 1.738,0.366 0.363,0.193 10 E36 2.184,0.221 2.546,0.415 0.363,0.193 10 AC1 1.676,1.063 1.889,0.311 1.889,0.311 2.15,0.311 false

w/ Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-11 (AC1) - Body ground
·

Engine idling

·

A/C switch off

·

Blower switch LO


11 to 14 V
E36-11 (AC1) - Body ground
·

Engine idling

·

A/C switch on

·

Blower switch LO


Below 1 V




b.
U166470E01
0.04,0.005 0.248,0.230 0.208,0.225 10 *a 1.559,0.2 1.835,0.342 0.276,0.142 10 E81 2.325,1.244 2.573,1.657 2.573,1.657 2.789,1.657 false 2.843,1.57 3.274,1.745 0.431,0.176 10 AC1

w/ Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-23 (AC1) - Body ground
·

Engine idling

·

A/C switch off

·

Blower switch LO


11 to 14 V
E81-23 (AC1) - Body ground
·

Engine idling

·

A/C switch on

·

Blower switch LO


Below 1 V




Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

Result
Result Proceed to
OK A
NG (for 1VD-FTV) B
NG (for 1GR-FE) C
NG (for 1UR-FE) D
NG (for 3UR-FE) E


A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

D

E

10.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER ASSEMBLY)

*1: for LHD

*2: for RHD


a.

w/ Rear Heater:

i.

Disconnect the A38*1 or A52*2 ECM connector.


ii.

Disconnect the E36 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-18 (ACT) - E36-22 (ACT)*1 Always Below 1 Ω
A52-18 (ACT) - E36-22 (ACT)*2 Always Below 1 Ω
A38-18 (ACT) or E36-22 (ACT) - Body ground*1 Always 10 kΩ or higher
A52-18 (ACT) or E36-22 (ACT) - Body ground*2 Always 10 kΩ or higher

for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E36-22 (ACT)*1 Always Below 1 Ω
A52-17 (ACT) - E36-22 (ACT)*2 Always Below 1 Ω
A38-17 (ACT) or E36-22 (ACT) - Body ground*1 Always 10 kΩ or higher
A52-17 (ACT) or E36-22 (ACT) - Body ground*2 Always 10 kΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E36-22 (ACT) Always Below 1 Ω
A38-17 (ACT) or E36-22 (ACT) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the A38*1 or A52*2 ECM connector.


ii.

Disconnect the E81 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-18 (ACT) - E81-27 (ACT)*1 Always Below 1 Ω
A52-18 (ACT) - E81-27 (ACT)*2 Always Below 1 Ω
A38-18 (ACT) or E81-27 (ACT) - Body ground*1 Always 10 kΩ or higher
A52-18 (ACT) or E81-27 (ACT) - Body ground*2 Always 10 kΩ or higher

for 1GR-FE, 1UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E81-27 (ACT)*1 Always Below 1 Ω
A52-17 (ACT) - E81-27 (ACT)*2 Always Below 1 Ω
A38-17 (ACT) or E81-27 (ACT) - Body ground*1 Always 10 kΩ or higher
A52-17 (ACT) or E81-27 (ACT) - Body ground*2 Always 10 kΩ or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-17 (ACT) - E81-27 (ACT) Always Below 1 Ω
A38-17 (ACT) or E81-27 (ACT) - Body ground Always 10 kΩ or higher





OK

11.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)

11.CHECK ECM
a.
U156666E03
1.74,1.208 1.875,2.01 1.875,2.01 2.146,2.01 false 0.042,0 0.302,0.198 0.26,0.198 10 false *a 1.375,0.188 1.74,0.385 0.365,0.198 10 false E36 2.219,1.906 2.583,2.104 0.365,0.198 10 false ACT

w/ Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See pageVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL ).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-22 (ACT) - Body ground
·

Engine idling

·

A/C switch off or on (magnet clutch off)

·

Blower switch LO


Below 1V
E36-22 (ACT) - Body ground
·

Engine idling

·

A/C switch on (magnet clutch on)

·

Blower switch LO


4.5 to 5.5 V




b.
U166471E02
2,1.26 2.208,1.677 2.208,1.677 2.427,1.677 false 0.083,0.094 0.292,0.323 0.208,0.229 10 false *a 1.594,0.24 1.865,0.385 0.271,0.146 10 false E81 2.479,1.583 2.906,1.76 0.427,0.177 10 false ACT

w/o Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-27 (ACT) - Body ground
·

Engine idling

·

A/C switch off or on (magnet clutch off)

·

Blower switch LO


Below 1V
E81-27 (ACT) - Body ground
·

Engine idling

·

A/C switch on (magnet clutch on)

·

Blower switch LO


4.5 to 5.5 V




Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

Result
Result Proceed to
OK A
NG (for 1VD-FTV) B
NG (for 1GR-FE) C
NG (for 1UR-FE) D
NG (for 3UR-FE) E


A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C

D

E