Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight (HI-BEAM) Circuit  


DESCRIPTION

The main body ECU receives a headlight hi switch information signal from the light control switch, and illuminates the headlight high beam.

WIRING DIAGRAM

E339662E02
3.156,2.073 4.49,2.323 1.333,0.25 10 false H-LP HI or H-LP RH 1.969,2.781 2.781,3 0.813,0.219 10 false H-LP LH-HI 2.01,3.448 3.188,3.667 1.177,0.219 10 false H-LP RH-HI 1.25,0.635 2.125,0.854 0.875,0.219 10 false from Battery 2.479,5.74 2.792,5.885 0.313,0.146 10 false A65 5.219,2.833 6.896,3.188 1.677,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.646,1.292 6.115,1.49 0.469,0.198 10 false DIM 4.115,1.188 4.302,1.396 0.188,0.208 10 false 2 3.24,1.198 3.406,1.396 0.167,0.198 10 false 1 4.125,1.677 4.323,1.875 0.198,0.198 10 false 5 3.271,1.656 3.438,1.875 0.167,0.219 10 false 3 2.448,7.469 2.781,7.615 0.333,0.146 10 false A68 2.333,4.917 2.479,5.104 0.146,0.188 10 false 3 4.333,4.927 4.479,5.115 0.146,0.188 10 false 6 2.323,6.656 2.552,6.865 0.229,0.208 10 false 3 4.333,6.656 4.5,6.896 0.167,0.24 10 false 6 2.448,7.615 3.948,7.833 1.5,0.219 10 false Headlight Assembly RH 2.479,5.906 4.688,6.073 2.208,0.167 10 false Headlight Assembly LH 5.458,1.146 5.646,1.292 0.188,0.146 10 false 1 5.208,2.677 5.594,2.823 0.385,0.146 10 false E118 2.521,4.917 2.729,5.073 0.208,0.156 10 false HI 4.156,4.917 4.365,5.073 0.208,0.156 10 false E 4.135,6.656 4.344,6.875 0.208,0.219 10 false E 2.521,6.656 2.771,6.844 0.25,0.188 10 false HI 0.906,1.479 2.802,1.729 1.896,0.25 10 false H-LP MAIN NO. 2 or H-LP LH 1.542,4.052 3.292,4.281 1.75,0.229 12 false for Helogen Headlight:

E339663E02
2.594,0.781 4.115,1.042 1.521,0.26 12 false for LED Headlight : 2.594,4.198 5.5,4.458 2.906,0.26 12 false for Halogen Headlight LED Headlight : 3.229,2.802 3.542,2.948 0.313,0.146 10 false A 2.604,7.5 2.938,7.646 0.333,0.146 10 false A68 1.375,1.677 1.521,1.865 0.146,0.188 10 false 3 1.375,2.375 1.521,2.563 0.146,0.188 10 false 6 3.031,1.667 3.177,1.854 0.146,0.188 10 false 1 3.031,2.354 3.177,2.542 0.146,0.188 10 false 2 2.604,7.667 4.104,7.885 1.5,0.219 10 false Headlight Assembly RH 3.229,2.969 5.438,3.135 2.208,0.167 10 false Headlight Unit RH 3.229,6.26 3.542,6.406 0.313,0.146 10 false A 3.031,5.156 3.177,5.344 0.146,0.188 10 false 1 3.031,5.813 3.177,6 0.146,0.188 10 false 2 3.229,6.438 5.438,6.604 2.208,0.167 10 false Headlight Unit RH 1.604,1.677 1.813,1.833 0.208,0.156 10 false HI 1.615,2.375 1.823,2.531 0.208,0.156 10 false E

E339664E02
2.427,0.74 3.948,1 1.521,0.26 12 false for LED Headlight : 2.417,4.198 5.323,4.458 2.906,0.26 12 false for Halogen Headlight LED Headlight : 3.083,2.781 3.396,2.927 0.313,0.146 10 false A 2.458,7.458 2.844,7.677 0.385,0.219 10 false A65 1.25,1.656 1.406,1.865 0.156,0.208 10 false 3 1.271,2.333 1.448,2.552 0.177,0.219 10 false 6 2.875,1.635 3.021,1.823 0.146,0.188 10 false 1 2.885,2.323 3.031,2.51 0.146,0.188 10 false 2 2.458,7.646 4.094,7.896 1.635,0.25 10 false Headlight Assembly LH 3.083,2.938 5.292,3.104 2.208,0.167 10 false Headlight Unit LH 3.083,6.26 3.302,6.438 0.219,0.177 10 false A 2.906,5.104 3.104,5.344 0.198,0.24 10 false 1 2.906,5.771 3.115,6.031 0.208,0.26 10 false 2 3.083,6.417 4.49,6.656 1.406,0.24 10 false Headlight Unit LH 1.427,1.646 1.677,1.833 0.25,0.188 10 false HI 1.438,2.333 1.646,2.521 0.208,0.188 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (HEAD LIGHT SW [HEAD])
a.

Operate the GTS according to the display and select the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Head Light SW (Head) Headlight switch signal / ON or OFF ON: Headlight switch (Head) on
OFF: Headlight switch (Head) off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.PERFORM ACTIVE TEST USING GTS (HEAD HI RELAY)
2.PERFORM ACTIVE TEST USING GTS (HEAD HI RELAY)
a.

Using the GTS, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Hi Headlight (Hi) ON or OFF -

OK:

Headlight high beam turns on/turns off.

Result
Result Proceed to
Headlights (Both high beams turn on) (for LHD) A
Headlights (Both high beams turn on) (for RHD) B
Headlights (Neither high beam turns on) C
Headlight on one side (High beam does not turn on) D
Headlight on one side (High beam does not turn on) [for Halogen Headlight] E




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

3.INSPECT HEADLIGHT RELAY (H-LP HI OR H-LP RH)

D

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP HI OR H-LP RH] - HEADLIGHT ASSEMBLY

E

3.INSPECT HEADLIGHT RELAY (H-LP HI OR H-LP RH)
a.

Remove the H-LP HI or H-LP RH relay from the engine room relay block, junction block.


b.

Inspect the H-LP HI or H-LP RH relay (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [H-LP HI OR H-LP RH])

NG

REPLACE HEADLIGHT RELAY (H-LP HI OR H-LP RH)

4.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [H-LP HI OR H-LP RH])
a.
E330818E02
0.067,0 0.255,0.173 0.187,0.173 10 *a

Remove the H-LP HI or H-LP RH relay from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 1- Body ground Always 11 to 14 V
Headlight relay terminal 3 - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Headlight Relay [H-LP HI or H-LP RH])



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP HI OR H-LP RH] - HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP HI OR H-LP RH] - HEADLIGHT ASSEMBLY
a.

Remove the H-LP HI or H-LP RH relay from the engine room relay block, junction block.


b.

Disconnect the A65*1 or A68*2 headlight connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A65-3 (HI) Always Below 1 Ω
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A68-3 (HI) Always Below 1 Ω
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - HEADLIGHT RELAY [H-LP HI OR H-LP RH]

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - HEADLIGHT RELAY [H-LP HI OR H-LP RH]
a.

Remove the H-LP HI or H-LP RH relay from the engine room relay block, junction block.


b.

Remove the cowl side junction block LH.


c.

Disconnect the E118 main body ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - E118-1 (DIM) Always Below 1 Ω
E118-1 (DIM) - Body ground Always 10 kΩ or higher

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP HI OR H-LP RH] - HEADLIGHT ASSEMBLY
a.

Remove the H-LP HI or H-LP RH relay from the engine room relay block, junction block.


b.

Disconnect the A65*1 or A68*2 headlight connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A65-3 (HI) Always Below 1 Ω
A65-6 (E) - Body ground Always
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A68-3 (HI) Always Below 1 Ω
A68-6 (E) - Body ground Always
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher




OK

8.INSPECT HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT HEADLIGHT ASSEMBLY
a.

for LED Headlight



b.

for Halogen Headlight and LED Headlight



c.

for LED Headlight

i.

Remove the headlight unit from the headlight assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY).



d.

for Halogen Headlight and LED Headlight

i.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LED Headlight
Tester Connection Condition Specified Condition
A-3 (B) - B-1 Always Below 1 Ω
A-6 (E) - B-2 Always 10 kΩ or higher

for Halogen Headlight and LED Headlight
Tester Connection Condition Specified Condition
A-3 (B) - B-1 Always Below 1 Ω
A-6 (E) - B-2 Always 10 kΩ or higher

Result
Result Proceed to
OK (for LED Headlight) A
OK (for Halogen Headlight and LED Headlight) B
NG (for LED Headlight) C
NG (for Halogen Headlight and LED Headlight) D




A

B

C

D