The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly.
The power distribution box assembly detects whether either the rear seat belts are fastened or unfastened based on the rear seat belt buckle switch condition and then sends the rear seat belt buckle switch status signal to the combination meter assembly.
The combination meter assembly illuminates, blinks or turns off the rear seat belt warning light on the combination meter assembly in accordance with the vehicle speed, rear seat belt state and front door state.
Rear No. 1 Seat Belt Warning
Rear No. 2 Seat Belt Warning (w/ Rear No. 2 Seat Belt Warning)
The seat belt warning system uses the CAN communication system and CXPI communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the combination meter assembly is replaced, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy Switch Status | Rear door courtesy light switch RH signal | OFF or ON | OFF: Rear door RH closed ON: Rear door RH open |
- |
| RL Door Courtesy Switch Status | Rear door courtesy light switch LH signal | OFF or ON | OFF: Rear door LH closed ON: Rear door LH open |
- |
| Tester Display |
|---|
| RR Door Courtesy Switch Status |
| RL Door Courtesy Switch Status |
The GTS display changes correctly in response to the rear door courtesy light switch condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Seat RH Buckle Switch Status | Rear RH seat belt buckle switch status | Set/Unset/Unknown | Set: Rear RH seat belt fastened Unset: Rear RH seat belt not fastened |
- |
| Rear Seat Center Buckle Switch Status | Rear center seat belt buckle switch status | Set/Unset/Unknown | Set: Rear center seat belt fastened Unset: Rear center seat belt not fastened |
- |
| Rear Seat LH Buckle Switch Status | Rear LH seat belt buckle switch status | Set/Unset/Unknown | Set: Rear LH seat belt fastened Unset: Rear LH seat belt not fastened |
- |
| Tester Display |
|---|
| Rear Seat RH Buckle Switch Status |
| Rear Seat Center Buckle Switch Status |
| Rear Seat LH Buckle Switch Status |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 3rd Right Seat Buckle / Occupant Detection Warning Switch | Rear No. 2 RH seat belt buckle switch status* | OFF or ON | OFF: Rear No. 2 RH seat belt fastened ON: Rear No. 2 RH seat belt not fastened |
- |
| 3rd Left Seat Buckle / Occupant Detection Warning Switch | Rear No. 2 LH seat belt buckle switch status* | OFF or ON | OFF: Rear No. 2 LH seat belt fastened ON: Rear No. 2 LH seat belt not fastened |
- |
*: w/ Rear No. 2 Seat Belt Warning
| Tester Display |
|---|
| 3rd Right Seat Buckle / Occupant Detection Warning Switch |
| 3rd Left Seat Buckle / Occupant Detection Warning Switch |
The GTS display changes correctly in response to the rear seat belt buckle switch condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Rear RH seat belt malfunction) | B |
| NG (Rear center seat belt malfunction) | C |
| NG (Rear LH seat belt malfunction) | D |
| NG (Rear No. 2 RH seat belt malfunction) (w/ Rear No. 2 Seat Belt Warning) | E |
| NG (Rear No. 2 LH seat belt malfunction) (w/ Rear No. 2 Seat Belt Warning) | F |
A
B
C
D
E
F
for 60/40 Split Seat Type RH Side:
for 40/20/40 Split Seat Type RH Side:
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 60/40 Split Seat Type RH Side:
for 40/20/40 Split Seat Type RH Side:
Disconnect the j7 rear No. 1 seat inner belt assembly RH connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(j7)Location & Routingewd_type=routing;type=c;code=j7 Click Connector(j7)Seat>Rear Seat Wire RH>Rear No. 1 Seat Belt Assembly Inner RHewd_type=component;type=c;code=j7;pinno=1,2 |
||
| j7-1 - 5F-8 | Always | Below 1 Ω |
| j7-2 - Body ground | Always | Below 1 Ω |
| j7-1 or 5F-8 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
NG
for 60/40 Split Seat Type RH Side:
for 40/20/40 Split Seat Type RH Side:
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 60/40 Split Seat Type RH Side:
for 40/20/40 Split Seat Type RH Side:
Disconnect the j3 rear center seat lap type belt assembly LH connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(j3)Location & Routingewd_type=routing;type=c;code=j3 Click Connector(j3)Seat>Rear Seat Wire RH>Rear Seat 3 Point Type Belt Assembly Centerewd_type=component;type=c;code=j3;pinno=1,2 |
||
| j3-1 - 5F-4 | Always | Below 1 Ω |
| j3-2 - Body ground | Always | Below 1 Ω |
| j3-1 or 5F-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
NG
Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT INNER BELT ASSEMBLY (for LH Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k5 rear No. 1 seat inner belt assembly LH connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k5)Location & Routingewd_type=routing;type=c;code=k5 Click Connector(k5)Seat>Rear Seat Wire LH>Rear No. 1 Seat Belt Assembly Inner LHewd_type=component;type=c;code=k5;pinno=1,2 |
||
| k5-1 - 5F-19 | Always | Below 1 Ω |
| k5-2 - Body ground | Always | Below 1 Ω |
| k5-1 or 5F-19 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Disconnect the Q49 rear seat wire RH connector.
Disconnect the I6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q49,I6)Location & Routingewd_type=routing;type=c,c;code=Q49,I6 |
||
| Q49-13 (IG) - I6-7 (RRBT) | Always | Below 1 Ω |
| Q49-13 (IG) or I6-7 (RRBT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q53 rear No. 1 seat inner belt assembly RH connector.
Disconnect the Q49 rear seat wire RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q53,Q49)Location & Routingewd_type=routing;type=c,c;code=Q53,Q49 |
||
| Q53-1 (+) - Q49-14 (L) | Always | Below 1 Ω |
| Q53-2 (E) - Body ground | Always | Below 1 Ω |
| Q53-1 (+) or Q49-14 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Disconnect the Q50 rear seat wire LH connector.
Disconnect the I6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q50,I6)Location & Routingewd_type=routing;type=c,c;code=Q50,I6 |
||
| Q50-13 (IG) - I6-24 (RLBT) | Always | Below 1 Ω |
| Q50-13 (IG) or I6-24 (RLBT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q54 rear No. 1 seat inner belt assembly LH connector.
Disconnect the Q50 rear seat wire LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q54,Q50)Location & Routingewd_type=routing;type=c,c;code=Q54,Q50 |
||
| Q54-1 (+) - Q50-14 (L) | Always | Below 1 Ω |
| Q54-2 (E) - Body ground | Always | Below 1 Ω |
| Q54-1 (+) or Q50-14 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
NG