Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P02351C  Turbocharger/Supercharger Boost Sensor "A" Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P023511.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P02351C Turbocharger/Supercharger Boost Sensor "A" Circuit Voltage Out of Range The discrepancy between the air volume estimated from the No. 2 turbo pressure sensor and the mass air flow meter output value equals or exceeds the threshold value.
·

No. 3 turbo pressure sensor (intake air temperature sensor)

·

No. 2 turbo pressure sensor

·

Mass air flow meter sub-assembly

·

No. 1 turbo pressure sensor

·

Wire harness or connector

·

ECM


- SAE: P0236

MONITOR DESCRIPTION

If the discrepancy between the air volume estimated from the No. 2 turbo pressure sensor and the mass air flow meter output value equals or exceeds the threshold value, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

A330723E40
3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.417,2.385 1.333,2.771 0.917,0.385 10 false Ignition switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [C] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.313,1.219 3.792,1.417 0.479,0.198 10 false [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P02351C.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [B] and [C] again.




WIRING DIAGRAM

Refer to DTC P010012 for mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P007A11 for intake air temperature sensor (No. 3 turbo pressure sensor) circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P007A11

Refer to DTC P023511 for No. 2 turbo pressure sensor circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P023511

Refer to DTC P012A11 for No. 1 turbo pressure sensor circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P012A11

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P02351C)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P02351C is output A
P02351C and other DTCs are output B


HINT:

If any DTCs other than P02351C are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
50003 372 229
A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) (15 psi(abs)).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.15 psi). This varies by weather.




b.

Compare the Atmospheric pressure value in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following A
Difference between Atmospheric Pressure in the Data List and normal atmospheric pressure value is 10 kPa (1.45 psi) or more. B




A

3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 (TURBO))

B

3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Remove the No. 3 turbo pressure sensor.

HINT:

Do not disconnect the connector.



b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
Result:
Result Proceed to
Other than the following A
Difference between Intake Air Temperature B1S1 (Turbo) in the Data List and actual outside air temperature value is 10°C (18°F) or more. B




A

4.READ VALUE USING GTS (MAF SENSOR)

B

19.INSPECT NO. 3 TURBO PRESSURE SENSOR (INTAKE AIR TEMPERATURE SENSOR)
4.READ VALUE USING GTS (MAF SENSOR)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


c.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Powertrain > Engine > Data List
Tester Display
MAF Sensor Bank1
MAF Sensor Bank2
50003 372 611,612
Standard:
GTS Display Condition Specified Condition
MAF Sensor Bank1 Engine warmed up
Shift position: N
A/C: Off
Engine Speed: 3000 rpm
Between 6.5 and 30.0 gm/sec
MAF Sensor Bank2 Between 6.5 and 30.0 gm/sec



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 2 TURBO PRESSURE SENSOR

NG

17.CHECK HARNESS AND CONNECTOR
5.INSPECT NO. 2 TURBO PRESSURE SENSOR

OK

6.INSPECT NO. 1 TURBO PRESSURE SENSOR

NG

15.CHECK HARNESS AND CONNECTOR
6.INSPECT NO. 1 TURBO PRESSURE SENSOR

OK

7.CHECK INTAKE SYSTEM

NG

13.CHECK HARNESS AND CONNECTOR
7.CHECK INTAKE SYSTEM
a.

Check that there is no air suction or blockage at any points in the intake system.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No air suction or blockage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P02351C)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P02351C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P02351C.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P02351C is output)
B




A

END

B

10.REPLACE NO. 2 TURBO PRESSURE SENSOR
10.REPLACE NO. 2 TURBO PRESSURE SENSOR

NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P02351C)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P02351C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P02351C.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P02351C is output)
B




A

END

B

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

14.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
14.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C23,C38,C22)Location & Routing

Click Connector(C23)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly RH

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C22)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly LH

C23-3 (VC) - C38-46 (VCPC) Always Below 1 Ω
C23-2 (PIC) - C38-42 (PIC) Always Below 1 Ω
C23-1 (E2) - C38-45 (EPIC) Always Below 1 Ω
C22-3 (VC2) - C38-44 (VPC2) Always Below 1 Ω
C22-2 (PIC2) - C38-41 (PIC2) Always Below 1 Ω
C22-1 (E22) - C38-43 (EPC2) Always Below 1 Ω
C23-3 (VC) or C38-46 (VCPC) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (PIC) or C38-42 (PIC) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (VC2) or C38-44 (VPC2) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (PIC2) or C38-41 (PIC2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C21)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

C21-3 (VC) - C21-1 (E2) Ignition switch ON 4.5 to 5.5 V
C21-2 (PTA) - C21-1 (E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C21)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

C21-3 (VC) - C21-2 (PTA) Ignition switch off 171 to 189 kΩ
C21-1 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

16.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
16.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C21,C37)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C21-3 (VC) - C37-92 (VPTA) Always Below 1 Ω
C21-2 (PTA) - C37-111 (PTA) Always Below 1 Ω
C21-1 (E2) - C37-91 (EPTA) Always Below 1 Ω
C21-3 (VC) or C37-92 (VPTA) - Body ground and other terminals Always 10 kΩ or higher
C21-2 (PTA) or C37-111 (PTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C24-3 (FGR) Ignition switch off 2.09 to 2.31 kΩ
C25-4 (VCC) - C25-3 (FG) Ignition switch off 2.09 to 2.31 kΩ
C24-2 (E2GR) - Body ground Always Below 1 Ω
C25-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C37,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C37-84 (VCVG) Always Below 1 Ω
C24-3 (FGR) - C37-78 (VG) Always Below 1 Ω
C24-2 (E2GR) - C37-83 (E2G) Always Below 1 Ω
C25-4 (VCC) - C37-82 (VVG2) Always Below 1 Ω
C25-3 (FG) - C37-76 (VG2) Always Below 1 Ω
C25-2 (E2G) - C37-81 (E2G2) Always Below 1 Ω
C24-4 (VCCR) or C37-84 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (FGR) or C37-78 (VG) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (VCC) or C37-82 (VVG2) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (FG) or C37-76 (VG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT NO. 3 TURBO PRESSURE SENSOR (INTAKE AIR TEMPERATURE SENSOR)

OK

20.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)

NG

20.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 3 turbo pressure sensor connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR