Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P001700  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B  P001900  Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B  


DESCRIPTION

Refer to DTC P001313.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P001313

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft of bank 1) signal
(2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

·

Camshaft timing oil control valve assembly (bank 1) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 1)

·

ECM


Comes on/- SAE: P0017
P001900 Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft of bank 2) signal
(2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

·

Camshaft timing oil control valve assembly (bank 2) (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly (bank 2)

·

ECM


Comes on/- SAE: P0019

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A197314E71
4.271,1.115 4.604,0.448 4.604,0.448 4.75,0.448 false 0.156,0.656 1.083,0.802 0.927,0.146 10 false Vehicle Speed 1.542,2.156 1.75,2.354 0.208,0.198 10 false [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 false [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 false [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 false [D] 4.625,0.865 4.823,1.063 0.198,0.198 10 false [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 false [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 false [G] 0.667,1.792 1.052,1.979 0.385,0.188 10 false Idling 4.813,0.365 6.292,0.729 1.479,0.365 10 false There is no designated vehicle speed 0.167,2.083 1.073,2.51 0.906,0.427 10 false Ignition Switch ON 1.917,2.573 2.708,2.906 0.792,0.333 10 false Warming up the engine 2.74,2.583 3.896,2.75 1.156,0.167 10 false 5 minutes or more 5.271,2.604 6.427,2.771 1.156,0.167 10 false 5 minutes or more 4.125,2.604 5.021,2.771 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Idle the engine for 5 minutes or more [C].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P001700 or P001900.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [E] through [G].



15.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Idle the engine for 5 minutes or more [F].

17.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Check the DTC judgment result.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by one tooth or more.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P001700 Bank 1
P001900 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001700 OR P001900)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001700 or P001900 is output A
P001700 or P001900 and other DTCs are output B


HINT:

If any DTCs other P001700 or P001900 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Start the engine.


b.

Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
50004 372 5 398
Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
Data List Display
Exhaust VVT Change Angle Bank 2
50004 372 46 470
OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

OK

6.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

6.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
HINT:

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700 OR P001900)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700 OR P001900)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P001700 or P001900 is output B




A

B