Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P001600  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  P001800  Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft, cam timing oil control solenoid assembly (for intake camshaft), camshaft timing oil control valve assembly [intake camshaft timing gear bolt assembly] and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001600 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Deviation in the crankshaft position sensor signal and camshaft position sensor (for intake camshaft of bank 1) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for intake camshaft of bank 1)

·

Camshaft timing oil control valve assembly (bank 1) [intake camshaft timing gear bolt assembly]

·

Camshaft timing intake gear assembly (bank 1)

·

ECM


Comes on/- SAE: P0016
P001800 Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A Deviation in the crankshaft position sensor signal and camshaft position sensor (for intake camshaft of bank 2) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for intake camshaft of bank 2)

·

Camshaft timing oil control valve assembly (bank 2) [intake camshaft timing gear bolt assembly]

·

Camshaft timing intake gear assembly (bank 2)

·

ECM


Comes on/- SAE: P0018

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A197314E71
4.271,1.115 4.604,0.448 4.604,0.448 4.75,0.448 false 0.156,0.656 1.083,0.802 0.927,0.146 10 false Vehicle Speed 1.542,2.156 1.75,2.354 0.208,0.198 10 false [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 false [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 false [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 false [D] 4.625,0.865 4.823,1.063 0.198,0.198 10 false [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 false [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 false [G] 0.667,1.792 1.052,1.979 0.385,0.188 10 false Idling 4.813,0.365 6.292,0.729 1.479,0.365 10 false There is no designated vehicle speed 0.167,2.083 1.073,2.51 0.906,0.427 10 false Ignition Switch ON 1.917,2.573 2.708,2.906 0.792,0.333 10 false Warming up the engine 2.74,2.583 3.896,2.75 1.156,0.167 10 false 5 minutes or more 5.271,2.604 6.427,2.771 1.156,0.167 10 false 5 minutes or more 4.125,2.604 5.021,2.771 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Idle the engine for 5 minutes or more [C].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P001600 or P001800.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [E] through [G].



15.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Idle the engine for 5 minutes or more [F].

17.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Check the DTC judgment result.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The monitor for this DTC detects when the timing chain is shifted by one tooth or more.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P001600 Bank 1
P001800 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001800)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001600 or P001800 is output A
P001600 or P001800 and other DTCs are output B


HINT:

If any DTCs other than P001600 or P001800 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Start the engine.


b.

Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 2
Data List Display
Intake VVT Change Angle Bank 2
50004 372 45 469
OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

OK

6.CLEAR DTC

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P001600 or P001800 is output B




A

B

8.REPLACE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY
8.REPLACE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY
HINT:

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

Perform "Inspection After Repair" after replacing the camshaft timing intake gear assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P001600 or P001800 is output B




A

END

B