Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM J

V35A-FTS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.CHECK WHETHER ENGINE CAN BE CRANKED

B

21.CHECK WHETHER ENGINE CAN BE CRANKED
2.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

3.READ VALUE USING GTS (STARTER SW)

B

20.READ VALUE USING GTS (STARTER SW)
3.READ VALUE USING GTS (STARTER SW)
a.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

4.INSPECT ST NO. 1 RELAY

NG

15.CHECK STOP AND START SYSTEM
4.INSPECT ST NO. 1 RELAY

OK

5.INSPECT ST NO. 2 RELAY

NG

REPLACE ST NO. 1 RELAY

5.INSPECT ST NO. 2 RELAY

OK

6.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 2 RELAY

6.INSPECT STARTER ASSEMBLY

OK

7.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 2 relay from No. 2 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

3 (ST NO. 2 relay) - C52-1 (SL2) Always Below 1 Ω
3 (ST NO. 2 relay) or C52-1 (SL2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)
a.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

2 (ST NO. 2 relay) - B1-34 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)
A485851C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.344,1.323 2.656,1.479 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 2 RELAY)

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

3 (ST NO. 1 relay) - C52-2 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or C52-2 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A485852C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.313,1.594 2.625,1.75 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

14.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK STOP AND START SYSTEM

OK

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)

NG

REPAIR STOP AND START SYSTEM

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,B1)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B38-23 (STA2) - B1-34 (STA) Always Below 1 Ω
B38-23 (STA2), B1-34 (STA) or 2 (ST NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - CERTIFICATION ECU)

NG

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - CERTIFICATION ECU)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the engine stop and start ECU connector.


c.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40,C34,C37,B38)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

I40-10 (STAR) - C34-4 (B) Always Below 1 Ω
I40-10 (STAR) - C37-7 (NSW) Always Below 1 Ω
I40-10 (STAR) - B38-17 (CLL) Always Below 1 Ω
I40-10 (STAR), C34-4 (B), C37-7 (NSW) or B38-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.READ VALUE USING GTS (STARTER SW)
a.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)

21.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

22.READ VALUE USING GTS (STARTER SW)

B

33.READ VALUE USING GTS (STARTER SW)
22.READ VALUE USING GTS (STARTER SW)
a.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

23.INSPECT ST NO. 1 RELAY

NG

30.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
23.INSPECT ST NO. 1 RELAY

OK

24.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

24.INSPECT STARTER ASSEMBLY

OK

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

25.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

3 (ST NO. 1 relay) - C52-2 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or C52-2 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C56)Location & Routing

Click Connector(C56)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

Positive (+) battery terminal - C56-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A485852C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.313,1.594 2.625,1.75 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

28.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

NG

31.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 2 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.READ VALUE USING GTS (STARTER SW)
a.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)