Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM J

V35A-FTS ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump assembly (for low pressure side) circuit consists of the ECM, fuel pump assembly (for low pressure side) and fuel pump control ECU (which operates the fuel pump assembly (for low pressure side)). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump assembly (for low pressure side) operation speed.

WIRING DIAGRAM

A485566E01
0.594,5.333 1.198,5.563 0.604,0.229 10 false Battery 0.74,1.469 1.979,1.698 1.24,0.229 10 false EFI MAIN NO. 1 2.99,1.646 4.229,1.875 1.24,0.229 10 false EFI MAIN NO. 1 2.281,0.802 3.094,1.021 0.813,0.219 10 false EFI NO. 2 4.344,1.719 5.156,1.938 0.813,0.219 10 false EFI-B NO. 4 0.49,4.042 1.635,4.333 1.146,0.292 10 false SUB R/B-NO. 1 0.76,2.781 1.854,2.979 1.094,0.198 10 false EFI MAIN NO. 2 4.458,2.979 5.552,3.177 1.094,0.198 10 false EFI MAIN NO. 2 1.583,6.167 3.063,6.625 1.479,0.458 10 false Fuel Pump Assembly (for Low Pressure Side) 3.615,6.063 5.208,6.323 1.594,0.26 10 false Fuel Pump Control ECU 3.198,5.688 3.802,5.917 0.604,0.229 10 false * 0.615,6.427 1.396,6.625 0.781,0.198 10 false *: Shielded 2.167,3.917 2.594,4.146 0.427,0.229 10 false BLPU 1.573,6.021 2,6.25 0.427,0.229 10 false V9 3.688,3.906 3.979,4.135 0.292,0.229 10 false V7 2.156,4.458 2.583,4.688 0.427,0.229 10 false BLPV 2.125,4.99 2.615,5.208 0.49,0.219 10 false BLPW 2.177,5.521 2.667,5.74 0.49,0.219 10 false BLPE 2.656,3.781 2.813,4 0.156,0.219 10 false 3 2.646,4.302 2.802,4.521 0.156,0.219 10 false 4 2.646,4.844 2.802,5.063 0.156,0.219 10 false 2 2.656,5.375 2.813,5.594 0.156,0.219 10 false 1 3.688,4.458 3.979,4.688 0.292,0.229 10 false V7 3.677,4.99 3.969,5.219 0.292,0.229 10 false V7 3.688,5.531 3.979,5.76 0.292,0.229 10 false V7 3.719,3.698 3.875,3.917 0.156,0.219 10 false 2 3.708,4.24 3.865,4.458 0.156,0.219 10 false 3 3.719,4.781 3.875,5 0.156,0.219 10 false 4 3.708,5.323 3.865,5.542 0.156,0.219 10 false 1 4.844,4.125 5.135,4.354 0.292,0.229 10 false V6 4.844,4.688 5.135,4.917 0.292,0.229 10 false V6 4.844,5.26 5.135,5.49 0.292,0.229 10 false V6 4.875,3.927 5.031,4.146 0.156,0.219 10 false 1 4.885,4.469 5.042,4.688 0.156,0.219 10 false 2 4.885,5.063 5.042,5.281 0.156,0.219 10 false 3 5.875,4.531 6.083,4.792 0.208,0.26 10 false 4 6.104,4.531 6.49,4.781 0.385,0.25 10 false FPC 5.833,0.521 5.99,0.74 0.156,0.219 10 false 3 6.073,0.646 6.604,0.906 0.531,0.26 10 false MREL 6.313,6.083 6.698,6.333 0.385,0.25 10 false B1 3.885,1.146 4.042,1.365 0.156,0.219 10 false 5 5.365,2.479 5.521,2.698 0.156,0.219 10 false 5 3.042,1.135 3.198,1.354 0.156,0.219 10 false 3 4.542,2.458 4.698,2.677 0.156,0.219 10 false 3 3.052,0.5 3.208,0.719 0.156,0.219 10 false 1 4.542,2 4.698,2.219 0.156,0.219 10 false 2 3.906,0.51 4.063,0.729 0.156,0.219 10 false 2 5.354,2 5.51,2.219 0.156,0.219 10 false 1 6.313,6.25 6.698,6.5 0.385,0.25 10 false ECM 4.417,4.688 4.802,4.938 0.385,0.25 10 false FPC 4.521,4.135 4.813,4.365 0.292,0.229 10 false +B 4.427,5.26 4.813,5.51 0.385,0.25 10 false GND 3.99,3.906 4.375,4.156 0.385,0.25 10 false FPU 3.99,4.448 4.375,4.698 0.385,0.25 10 false FPV 3.99,4.99 4.375,5.24 0.385,0.25 10 false FPW 3.99,5.51 4.375,5.76 0.385,0.25 10 false FPG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FUEL LEAK
a.

Check around and beneath the vehicle for fuel leaks, fumes, etc.

OK:

No fuel leaks present.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (BRUSHLESS))

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (BRUSHLESS))
a.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay (Brushless)
50004 372 40
Standard:
GTS Operation Standard
ON Operating sounds can be heard from fuel pump assembly (for low pressure side)



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

NG

7.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)
a.

Install the fuel pressure gauge (for low pressure line of low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


b.

Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.

Powertrain > Engine > Active Test
Active Test Display
Control the Fuel Pump Duty Ratio
Data List Display
Fuel Pressure (Low) / Fuel Pressure 2
Fuel Pump Control Duty Ratio
50004 372 39 267,101
Standard:
GTS Operation Standard
Low Data List value and fuel pressure gauge are within +/-50 kPa of each other
High



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FUEL PRESSURE)

NG

REPLACE NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

4.READ VALUE USING GTS (FUEL PRESSURE)
a.

Read the values displayed on the GTS while the engine is cranking.

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (Low) / Target Fuel Pressure 2
Fuel Pressure (Low) / Fuel Pressure 2
Low Fuel Pressure Sensor
50003 372 266,267,545
Result:
Result Proceed to
Low Fuel Pressure Sensor value is within +/- 65 kPag of the Target Fuel Pressure (Low) / Target Fuel Pressure 2 A
Low Fuel Pressure Sensor value is more than 65 kPag higher than the target fuel pressure (low) / Target Fuel Pressure 2 B
Low Fuel Pressure Sensor value is more than 65 kPag lower than the target fuel pressure (low) / Target Fuel Pressure 2 C




A

5.CHECK FUEL PRESSURE

B

REPLACE FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE) (FUEL WITH FILTER PUMP ASSEMBLY)

for Single Tank Type: Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for Single Tank Type)>REMOVAL

for Double Tank Type: Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for Double Tank Type)>REMOVAL

HINT:

Relief blockage such as clogging of the jet pump is suspected.



C

6.CHECK SHORTAGE OF FUEL
5.CHECK FUEL PRESSURE
a.

Install the fuel pressure gauge (for low pressure line of low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


b.

Start the engine.


c.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



d.

Stop the engine.


e.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

98 kPa (1.0 kgf/cm2, 14.2 psi) or more


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE) (FUEL WITH FILTER PUMP ASSEMBLY)

6.CHECK SHORTAGE OF FUEL
a.

Check the amount of fuel remaining.


HINT:
·

No fuel remains in the fuel tank: Malfunction of the fuel sender gauge assembly is suspected.

·

Only the fuel pump side fuel chamber has no fuel remaining: Malfunction of the jet pump is suspected.

·

Fuel remains in the fuel tank: Malfunction of the fuel pump assembly (for low pressure side) is suspected.

·

Perform "Inspection After Repair" after replacing the fuel pump assembly (for low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

REPLACE FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE) (FUEL WITH FILTER PUMP ASSEMBLY)

7.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
a.

Disconnect the fuel pump assembly (for low pressure side) connector.


b.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49
Standard Voltage:
Tester Connection GTS Operation Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>Differential Wire / Frame Wire>Fuel with Filter Pump Assembly

V9-3 (BLPU) - Body ground U Phase 4.4 to 8.4 V*
V9-4 (BLPV) - Body ground V Phase 4.4 to 8.4 V*
V9-2 (BLPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test restricts the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).

·

Perform "Inspection After Repair" after replacing the fuel pump assembly (for low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE) (FUEL WITH FILTER PUMP ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE))
8.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP ASSEMBLY (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the fuel pump assembly (for low pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V7,V9)Location & Routing

Click Connector(V7)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

Click Connector(V9)Body>Differential Wire / Frame Wire>Fuel with Filter Pump Assembly

V7-2 (FPU) - V9-3 (BLPU) Always Below 1 Ω
V7-3 (FPV) - V9-4 (BLPV) Always Below 1 Ω
V7-4 (FPW) - V9-2 (BLPW) Always Below 1 Ω
V7-2 (FPU) or V9-3 (BLPU) - Body ground and other terminals Always 10 kΩ or higher
V7-3 (FPV) or V9-4 (BLPV) - Body ground and other terminals Always 10 kΩ or higher
V7-4 (FPW) or V9-2 (BLPW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for low pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)
a.

Disconnect the fuel pump control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(V6)Location & Routing

Click Connector(V6)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

V6-1 (+B) - V6-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.INSPECT ECM (FPC TERMINAL)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
10.INSPECT ECM (FPC TERMINAL)
a.

Disconnect the fuel pump control ECU connector.


b.

Operate the fuel pump control ECU using the Active Test function and measure the resistance according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49
Standard Resistance:
Tester Connection GTS Operation Specified Condition

Click Location & Routing(V6)Location & Routing

Click Connector(V6)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

V6-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V6,B1)Location & Routing

Click Connector(V6)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

V6-2 (FPC) - B1-4 (FPC) Always Below 1 Ω
V6-2 (FPC) or B1-4 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
a.

Disconnect the fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V6)Location & Routing

Click Connector(V6)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

V6-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI MAIN NO. 2 RELAY)
A485850C01
0.094,0.052 0.406,0.208 0.313,0.156 10 false *1 2.448,1.594 2.76,1.75 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 2 Relay


a.

Remove the EFI MAIN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.INSPECT EFI MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN NO. 2 RELAY)

14.INSPECT EFI MAIN NO. 2 RELAY

OK

15.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 1 - EFI MAIN NO. 2 RELAY)

NG

REPLACE EFI MAIN NO. 2 RELAY

15.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 1 - EFI MAIN NO. 2 RELAY)
a.

Remove the EFI MAIN NO. 1 and EFI MAIN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Remove the IGT/INJ relay, A/F relay and EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.

HINT:

Remove the IGT/INJ relay, A/F relay and EFI MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI MAIN NO. 1 relay) - 2 (EFI MAIN NO. 2 relay) Always Below 1 Ω
5 (EFI MAIN NO. 1 relay) or 2 (EFI MAIN NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)
a.

Remove the EFI MAIN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the fuel pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V6)Location & Routing

Click Connector(V6)Body>Differential Wire / Frame Wire>Fuel Pump Control ECU

5 (EFI MAIN NO. 2 relay) - V6-1 (+B) Always Below 1 Ω
5 (EFI MAIN NO. 2 relay) or V6-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR