Refer to DTC P048012.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P048012
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P04807F | Fan 1 Performance/Stuck Off Actuator Stuck Off | When the engine coolant temperature, air conditioning refrigerant pressure or exhaust gas temperature is high and the target engagement rate of the coupling fan is 80% or more, the coupling fan speed is lower than the stuck closed judgment speed for 60 seconds or more. (1 trip detection logic) |
·
Fluid coupling assembly
·
Wire harness or connector
·
Fan and generator V belt
·
V-Ribbed belt tensioner assembly
·
ECM |
Does not come on | SAE Code: P2B2F |
Refer to DTC P048012.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P048012
Refer to DTC P052631.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P052631
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P04807F and other DTCs are output | A |
| P04807F is output | B |
If any DTCs other than P04807F are output, troubleshoot those DTCs first.
A
B
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>DRIVE BELT>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>DRIVE BELT>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fan control solenoid (fluid coupling assembly) connector.
Operate the fan control solenoid using the Active Test function and measure the resistance according to the value(s) in the table below.
| Tester Display |
|---|
| Control the Electronic Control Coupling Fan |
| Tester Connection | GTS Operation | Specified Condition |
|---|---|---|
Click Location & Routing(C165)Location & Routingewd_type=routing;type=c;code=C165 |
||
| C165-3 (GDFC) - Body ground | During Active Test | Resistance fluctuates* |
*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the GDFC terminal will be unstable during the Active Test. If the resistance fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.
| Proceed to |
|---|
| OK |
| NG |
OK
NG