The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication. The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B14227F | Compressor Actuator Stuck Off | Diagnosis Condition: Cooler compressor assembly operating Malfunction Status: Open or short in compressor circuit Detection Time: Continuously for 30 seconds or more |
·
Cooler compressor assembly
·
Harness or connector
·
Semiconductor power integration ECU
·
ECM
·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Cooler compressor assembly operating | ○ | ○ |
| Malfunction Status | Open in compressor circuit | ○ | - |
| Short in compressor circuit | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
If the conditions of either of these patterns are detected, a DTC will be stored.
ECM malfunctions can affect the storage of this DTC. Therefore, check all ECM DTCs and confirm that the system is normal before performing the following inspection.
The air conditioning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Pre-procedure1
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I32)Location & Routingewd_type=routing;type=c;code=I32 |
||
| I32-19 (MGC) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch: On (magnet clutch on) |
Below 1 V |
| I32-19 (MGC) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch : Off or on (magnet clutch off) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Fuse Shut Off Status | Magnet clutch assembly fuse shut off status | OFF/ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Magnetic Clutch Fuse Shut Off Status |
OFF is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Input Signal | Magnet clutch assembly input signal | OFF/ON | OFF: Magnet clutch assembly signal not input ON: Magnet clutch assembly signal input |
- |
| Tester Display |
|---|
| Magnetic Clutch Input Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Output Signal | Magnet clutch assembly output signal | OFF/ON | OFF: Magnet clutch assembly off ON: Magnet clutch assembly on |
- |
| Tester Display |
|---|
| Magnetic Clutch Output Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the C39 compressor with magnet clutch connector.
Disconnect the B57 semiconductor power integration ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C39,B57)Location & Routingewd_type=routing;type=c,c;code=C39,B57 |
||
| C39-1 (MG+) - B57-4 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the C39 compressor with magnet clutch connector.
Procedure1
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Fuse Shut Off Status | Magnet clutch assembly fuse shut off status | OFF/ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Magnetic Clutch Fuse Shut Off Status |
OFF is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the C39 cooler compressor assembly connector.
Disconnect the B57 semiconductor power integration ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C39,B57)Location & Routingewd_type=routing;type=c,c;code=C39,B57 |
||
| C39-1 (MG+) or B57-4 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I32 air conditioning amplifier assembly connector.
Disconnect the B57 semiconductor power integration ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I32,B57)Location & Routingewd_type=routing;type=c,c;code=I32,B57 |
||
| I32-19 (MGC) - B57-5 (MGC) | Always | Below 1 Ω |
| I32-19 (MGC) or B57-5 (MGC) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I33 air conditioning amplifier assembly connector.
Disconnect the B2*1, B1*2 or B70*3 ECM connector.
*1: for 1GR-FE
*2: for V35A-FTS
*3: for F33A-FTV
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33,B2)Location & Routingewd_type=routing;type=c,c;code=I33,B2 |
||
| I33-19 (AC1) - B2-9 (AC1) | Always | Below 1 Ω |
| I33-3 (ACT) - B2-17 (ACT) | Always | Below 1 Ω |
| I33-19 (AC1) or B2-9 (AC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| I33-3 (ACT) or B2-17 (ACT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33,B1)Location & Routingewd_type=routing;type=c,c;code=I33,B1 |
||
| I33-19 (AC1) - B1-61 (AC1) | Always | Below 1 Ω |
| I33-3 (ACT) - B1-52 (ACT) | Always | Below 1 Ω |
| I33-19 (AC1) or B1-61 (AC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| I33-3 (ACT) or B1-52 (ACT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33,B70)Location & Routingewd_type=routing;type=c,c;code=I33,B70 |
||
| I33-19 (AC1) - B70-34 (AC1) | Always | Below 1 Ω |
| I33-3 (ACT) - B70-33 (ACT) | Always | Below 1 Ω |
| I33-19 (AC1) or B70-34 (AC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| I33-3 (ACT) or B70-33 (ACT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33)Location & Routingewd_type=routing;type=c;code=I33 |
||
| I33-19 (AC1) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
A/C switch: On |
Below 1 V |
| I33-19 (AC1) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
"A/C" switch: Off |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33)Location & Routingewd_type=routing;type=c;code=I33 |
||
| I33-3 (ACT) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
A/C switch: Off or on (magnet clutch off) |
Below 1 V |
| I33-3 (ACT) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
A/C switch: On (magnet clutch on) |
4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
for 1GR-FE:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 1GR-FE)>INSPECTION
for V35A-FTS:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for V35A-FTS)>INSPECTION
for F33A-FTV:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for F33A-FTV)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the air conditioning amplifier assembly with its connectors still connected
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Procedure1
Using an oscilloscope, check the waveform.
| Tester Connection | Tool Setting | Condition |
|---|---|---|
Click Location & Routing(I32)Location & Routingewd_type=routing;type=c;code=I32 |
||
| I32-12 (LOCK) - I32-14 (SG-2) | 200 mV/DIV., 10 ms/DIV. |
·
Engine idling
·
A/C switch: On (magnet clutch on)
·
Blower switch: LO |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I32 air conditioning amplifier assembly connector.
Disconnect the C39 cooler compressor assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I32,C39)Location & Routingewd_type=routing;type=c,c;code=I32,C39 |
||
| I32-12 (LOCK) - C39-3 (SSR+) | Always | Below 1 Ω |
| I32-14 (SG-2) - C39-2 (SSR-) | Always | Below 1 Ω |
| C39-3 (SSR+) - C39-2 (SSR-) | Always | 10 kΩ or higher |
| I32-12 (LOCK) or C39-3 (SSR+) - Other terminals and body ground | Always | 10 kΩ or higher |
| I32-14 (SG-2) or C39-2 (SSR-) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG