When the seat heater switch (rear left) is operated, the air conditioning amplifier assembly receives the signal from the cooler control assembly via the LIN communication line and operates the rear left side seat heater.
If the battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.
for 1GR-FE: Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for V35A-FTS: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for F33A-FTV: Click herePower Source / Network>F33A-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
w/ Power Tilt and Power Telescopic Steering Column
If the mirror heater is operated when the battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the mirror heater may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X21B6" is not stored before proceeding with troubleshooting.
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Seat Heater | Rear left side seat heater operation | OFF/ON | - |
| Tester Display |
|---|
| Rear Left Seat Heater |
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioner amplifier assembly with a new one or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the rear left side seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k1 seat heater control sub-assembly (rear seat LH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k1)Location & Routingewd_type=routing;type=c;code=k1 Click Connector(k1)Seat>Rear Seat Wire LH>Seat Heater Control Sub-Assembly LH (Rear Seat LH)ewd_type=component;type=c;code=k1;pinno=1 |
||
| k1-1 (+B1) - Body ground | Ignition switch ON | 11 to 14 V |
| k1-1 (+B1) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I31 air conditioning amplifier assembly connector.
Disconnect the k1 seat heater control sub-assembly (rear seat LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I31,k1)Location & Routingewd_type=routing;type=c,c;code=I31,k1 Click Connector(k1)Seat>Rear Seat Wire LH>Seat Heater Control Sub-Assembly LH (Rear Seat LH)ewd_type=component;type=c;code=k1;pinno=5 |
||
| I31-24 (SM2L) - k1-5 (SWR) | Always | Below 1 Ω |
| I31-24 (SM2L) or k1-5 (SWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k2 rear No. 1 seat cushion heater assembly LH connector.
Disconnect the k1 seat heater control sub-assembly (rear seat LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k2,k1)Location & Routingewd_type=routing;type=c,c;code=k2,k1 Click Connector(k2)Seat>Rear Seat Wire LH>Rear Seat Cushion Heater LH (Rear No. 1 Seat Cushion Pad LH)ewd_type=component;type=c;code=k2;pinno=3,1 Click Connector(k1)Seat>Rear Seat Wire LH>Seat Heater Control Sub-Assembly LH (Rear Seat LH)ewd_type=component;type=c;code=k1;pinno=10,7 |
||
| k2-3 - k1-10(E) | Always | Below 1 Ω |
| k2-1 - k1-7(HTR) | Always | Below 1 Ω |
| k2-3 or k1-10 (E) - Body ground | Always | 10 kΩ or higher |
| k2-1 or k1-7(HTR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k2 rear No. 1 seat cushion heater assembly LH connector.
Disconnect the k6 rear No. 1 seatback heater assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k2,k6)Location & Routingewd_type=routing;type=c,c;code=k2,k6 Click Connector(k2)Seat>Rear Seat Wire LH>Rear Seat Cushion Heater LH (Rear No. 1 Seat Cushion Pad LH)ewd_type=component;type=c;code=k2;pinno=5,8 Click Connector(k6)Seat>Rear Seat Wire LH>Rear Seat Back Heater LH (No. 1 Seat Back Pad LH)ewd_type=component;type=c;code=k6;pinno=1,2 |
||
| k2-5 - k6-1 | Always | Below 1 Ω |
| k2-5 or k6-1 - Other terminals | Always | 10 kΩ or higher |
| k2-8 - k6-2 | Always | Below 1 Ω |
| k2-8 or k6-2 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for LH Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER (for LH Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seat heater control sub-assembly (rear seat LH) with a new one or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER CONTROL (for Rear LH)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the rear left side seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
Rear left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG