Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL › from 2021.07
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473037 FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential side gear shaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 3.DRAIN DIFFERENTIAL OIL

Hide 43420 4.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 5.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43420H 6.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C457991N01
2.115,1.833 1.917,1.833 1.917,1.833 1.76,1.313 true 2.198,1.719 2.708,1.938 0.51,0.219 10 true SST

Using SST, tap out the differential side gear shaft oil seal.

SST
09308-00010  


Hide 43410M 7.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 43420H 8.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C459316C01
5.656,0.448 5.802,0.448 5.802,0.448 5.885,0.719 true 5.667,1.365 6,1.365 true 4.833,2.385 4.646,2.385 4.646,2.385 4.646,1.302 true 4.594,2.625 4.406,2.625 4.406,2.625 4.406,1.313 true 5.479,0.365 5.792,0.521 0.313,0.156 10 false *1 5.438,1.292 5.75,1.448 0.313,0.156 10 false *2 6.042,0.302 6.354,0.458 0.313,0.156 10 false *a 6.042,2.333 6.354,2.49 0.313,0.156 10 false *a 4.875,2.26 5.365,2.479 0.49,0.219 10 false SST 4.625,2.5 5.115,2.719 0.49,0.219 10 false SST
*1 Differential Carrier *2 Front Drive Shaft Oil Seal LH
*a Gap - -


i.

Using SST and a hammer, tap in a new front drive shaft oil seal LH.

SST
09223-15020  
09502-12010  
09950-70010  (09951-07150)

Standard oil seal gap:
for LH Side:

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:
·

Make sure that the lip of the front drive shaft oil seal is inserted into SST before tapping in the front drive shaft oil seal LH.

·

Do not damage the front drive shaft oil seal LH.





Hide 43410M 9.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C459317C01
1.74,0.906 1.781,1.042 1.781,1.042 1.854,1.042 true 1.646,1.396 1.823,1.396 true 3.313,2.406 3.125,2.406 3.125,2.406 3.125,1.323 true 2.979,2.573 2.792,2.573 2.792,2.573 2.792,1.26 true 1.875,0.969 2.188,1.125 0.313,0.156 10 false *1 1.854,1.323 2.167,1.479 0.313,0.156 10 false *2 1.5,0.271 1.813,0.427 0.313,0.156 10 false *a 1.479,2.354 1.792,2.51 0.313,0.156 10 false *a 3.354,2.302 3.844,2.521 0.49,0.219 10 false SST 3.031,2.49 3.521,2.708 0.49,0.219 10 false SST
*1 Differential Tube *2 Front Drive Shaft Oil Seal RH
*a Gap - -


i.

Using SST and a hammer, tap in a new front drive shaft oil seal RH.

SST
09223-15020  
09502-12010  
09950-70010  (09951-07150)

Standard oil seal gap:

-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)


NOTICE:
·

Make sure that the lip of the front drive shaft oil seal is inserted into SST before tapping in the front drive shaft oil seal RH.

·

Do not damage the front drive shaft oil seal RH.





Hide 43420 10.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 11.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 12.ADD DIFFERENTIAL OIL