Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2021.07
RM38G0E _52 Drivetrain _101647 DRIVE SHAFT / PROPELLER SHAFT _0473033 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487300N29
1.958,2.458 1.958,2.938 false 0.875,1.448 1,1.01 1,1.01 1.208,1.01 false 3.729,2.219 3.729,2.688 3.729,2.688 3.906,2.688 false 5.698,1.781 5.698,2.25 false 1.667,2.719 1.927,2.906 0.26,0.188 10 false x 2 3.99,2.521 4.26,2.865 0.271,0.344 18 false 1 5.635,2.26 5.906,2.604 0.271,0.344 18 false 2 3.073,2.313 3.375,2.521 0.302,0.208 10 false x 5 1.854,2.99 2.083,3.177 0.229,0.188 10 false *1 6.365,2.063 6.927,2.281 0.563,0.219 10 false x 6 (*A) 1.281,0.917 1.51,1.104 0.229,0.188 10 false *2 0.938,2.104 1.24,2.292 0.302,0.188 10 false x 2 6.354,2.271 7.115,2.49 0.76,0.219 10 false x 4 (*B *D) 6.333,2.5 7.156,2.719 0.823,0.219 10 false x 2 (*C *E)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 NO. 2 ENGINE UNDER COVER ASSEMBLY 51420 - - -

*A for V35A-FTS, w/ Cover *B for V35A-FTS, w/o Cover
*C for 1GR-FE *D for F33A-FTV, w/ Cover
*E for F33A-FTV, w/o Cover - -
*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH

C458024N01
3.292,2.844 3.885,2.844 true 6.177,0.219 6.771,0.219 true 3.438,3.958 3.438,5.042 3.438,5.042 3.781,5.042 true 6.073,5.031 6.667,5.031 true 5.823,0.052 6.104,0.406 0.281,0.354 18 false 3 4.458,2.656 4.74,3.01 0.281,0.354 18 false 6 6.698,4.854 6.979,5.208 0.281,0.354 18 false 4 4.177,4.885 4.458,5.24 0.281,0.354 18 false 5 4.281,2.719 4.438,2.917 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

3 DIFFERENTIAL OIL - - -
4 STEERING KNUCKLE - - - -
5 FRONT DRIVE SHAFT ASSEMBLY LH 43420 (Click here) - -
6 FRONT DRIVE SHAFT HOLE SNAP RING 43420G (Click here) - -

V103638

Do not apply lubricants to the threaded parts ● Non-reusable part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front drive shaft assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 3.DRAIN DIFFERENTIAL OIL

Hide 4.REMOVE STEERING KNUCKLE

Hide 43420 5.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C458026N01
4.177,1.208 4.427,1.063 4.427,1.063 4.604,1.063 true 4.677,0.99 5.135,1.188 0.458,0.198 10 true SST 0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Using SST, remove the front drive shaft assembly LH.

SST
09520-01011  
09520-20010  (09521-02040, 09521-02060, 09521-02010)

NOTICE:
·

Do not damage the differential side gear shaft oil seal LH, inboard joint boot and front drive shaft dust cover LH.

·

Do not drop the front drive shaft assembly LH.

·

When carrying the front drive shaft assembly LH, hold it horizontally.



HINT:

Hook the SST claw at the position shown in the illustration to remove the front drive shaft assembly LH.




Hide 43420G 6.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C458028N01
0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Using a screwdriver, remove the front drive shaft hole snap ring.

NOTICE:

Do not damage the spline of the inboard joint.