Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P200C  Diesel Particulate Filter Over Temperature Bank 1  P200E  Catalyst System Temperature Too High Bank 1  P2428  Exhaust Gas Temperature Too High Bank 1  


DESCRIPTION

A351107C02
2.031,2.771 2.135,2.771 2.135,2.771 2.385,2.5 true 0.271,0.677 0.583,0.875 0.313,0.198 10 false *a 0.833,0.448 1.146,0.646 0.313,0.198 10 false *1 2.854,1.469 3.094,1.688 0.24,0.219 10 false *5 3.042,2.052 3.354,2.25 0.313,0.198 10 false *6 2.885,2.823 3.198,3.021 0.313,0.198 10 false *7 2.854,3.323 3.167,3.521 0.313,0.198 10 false *4 6.229,1.958 6.542,2.156 0.313,0.198 10 false *8 1.531,1.76 1.771,1.979 0.24,0.219 10 false *2 1.844,2.719 2.156,2.917 0.313,0.198 10 false *3
*1 Exhaust Fuel Addition Injector Assembly *2 Turbocharger Sub-assembly
*3 DPF Catalytic Converter *4 Air Fuel Ratio Sensor
*5 Exhaust Gas Temperature Sensor *6 No. 2 Exhaust Gas Temperature Sensor
*7 No. 3 Exhaust Gas Temperature Sensor *8 ECM
*a Exhaust Gas - -


The exhaust fuel addition injector assembly is mounted on the exhaust port of the cylinder head, and low pressure fuel is supplied to the exhaust fuel addition injector assembly by the feed pump in the supply pump assembly. This exhaust fuel addition injector assembly adds fuel in response to a control signal from the ECM, in order to perform PM forced regeneration.

During PM forced regeneration, the exhaust fuel addition injector assembly adds fuel to raise the DPF* catalyst temperature.

*: Diesel Particulate Filter

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

If DTC P200C, P200E and P2428 are present, refer to the diagnostic trouble code (DTC) chart for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P200C Diesel Particulate Filter Over Temperature Bank 1 The value of "Exhaust Temperature B1S3" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic).
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Front exhaust pipe assembly


Sub Trouble Area
·

No. 3 exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Fuel injector

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P200E Catalyst System Temperature Too High Bank 1 The value of "Exhaust Temperature B1S2" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic).
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Front exhaust pipe assembly


Sub Trouble Area
·

No. 2 exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Fuel injector

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P2428 Exhaust Gas Temperature Too High Bank 1 The value of "Exhaust Temperature B1S1" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic).
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Front exhaust pipe assembly


Sub Trouble Area
·

Exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Fuel injector

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

HINT:
·

Due to fail-safe operation when other DTCs (that involve the engine power limit) are stored, PM forced regeneration may be prohibited.

This DTC or P20CF, P244B, P244C and P2463 may be stored due to the fact that PM forced regeneration is prohibited due to the fail-safe operation of other DTCs.

·

The air fuel ratio and the exhaust gas temperature can be checked by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Diesel Exhaust / AF Lambda B1S1, Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

·

Malfunctions in the engine itself may affect the DPF system control and cause storage of this DTC. For example, malfunctions in the injector assemblies that cause a large amount of smoke emission: These affect the exhaust fuel addition injector assembly operation. Blockages or leaks in the air intake system, or an EGR system malfunction such as EGR passage blockages: These malfunctions affect the DPF catalyst temperature control. Therefore, the engine condition itself should also be checked, in addition to the exhaust fuel addition injector assembly.



Related Data List
DTC No. Data List
P200C
·

MAF

·

MAP

·

Intake Air Temp (Turbo)

·

Target Booster Pressure

·

Atmosphere Pressure

·

Coolant Temp

·

Engine Speed

·

AFS Voltage B1S1

·

AF Lambda B1S1

·

Exhaust Fuel Addition FB

·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Catalyst Differential Press

·

Injection Feedback Val #1 to #8

·

Injection Volume


P200E
P2428

MONITOR DESCRIPTION

The ECM monitors the DPF catalyst temperature. When the temperature becomes high due to uncombusted fuel, engine oil or thermal degradation to the DPF catalyst, the ECM illuminates the MIL.

A244058E14
3.927,1.177 3.406,0.469 3.406,0.469 3.135,0.469 false 0.104,0.083 1.542,0.417 1.438,0.333 10 false Malfunction Detection: 0.156,1.76 1.542,2.417 1.385,0.656 10 false Exhaust Temperature B1S1, B1S2 or B1S3 3.906,0.656 4.76,0.99 0.854,0.333 10 false MIL Goes On 5.823,1.073 7.094,1.5 1.271,0.427 10 false P200C, P200E and P2428 Threshold 2.49,0.385 3.115,0.719 0.625,0.333 10 false Abnormal 3.688,2 6.156,2.188 2.469,0.188 10 false Normal (302 to 572°C) 5.646,1.771 6.125,2.104 0.479,0.333 10 false Normal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P200C PM forced regeneration*
*: When P200C is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
P200E PM forced regeneration*
*: When P200E is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
P2428 PM forced regeneration*
*: When P2428 is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Check the values of "Exhaust Temperature B1S1", "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" that were saved in Procedure 1.

Result
Result Items to be Replaced
DTC P2428 is output and the value of "Exhaust Temperature B1S1" is 850°C (1562°F) or higher Exhaust gas temperature sensor
DTC P200E is output and the value of "Exhaust Temperature B1S2" is 850°C (1562°F) or higher No. 2 exhaust gas temperature sensor
DTC P200C is output and the value of "Exhaust Temperature B1S3" is 850°C (1562°F) or higher No. 3 exhaust gas temperature sensor


b.

If DTC P200C, P200E and/or P2428 is output, the exhaust gas temperature sensors need to be replaced. However, make sure to perform all diagnostic procedures for P200C, P200E and/or P2428 before replacing the exhaust gas temperature sensors.

HINT:

If the exhaust gas temperature sensors are subjected to an abnormally high temperature, the internal resistance of the sensor increases. This causes incorrect temperature measurement.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR BLACK SMOKE
3.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedure [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL INJECTION SYSTEM

NG

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (DPF CATALYTIC CONVERTER)
4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Even though it has been determined that the front exhaust pipe assembly (DPF catalytic converter) needs to be replaced, make sure to perform all diagnostic procedures for DTC P200C, P200E and/or P2428 before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

5.CHECK FUEL INJECTION SYSTEM
5.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

6.CHECK INTAKE / EXHAUST SYSTEM
6.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

7.CHECK AFTER TREATMENT CONTROL SYSTEM
7.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

8.REPLACE MALFUNCTIONING PARTS
8.REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P200C, P200E and/or P2428.


a.

Replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (for 5 Door)>REMOVAL

NOTICE:

Perform initialization procedure for Catalyst Record Clear and DPF Deterioration Record Clear.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION






Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



Result:
Proceed to
NEXT



NEXT

END