Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P244B  Diesel Particulate Filter Differential Pressure Too High  


DESCRIPTION

Refer to DTC P244C.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P244C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P244B Diesel Particulate Filter Differential Pressure Too High While driving, catalyst differential pressure becomes more than 0.45 for 3 seconds (1 trip detection logic).
·

Front exhaust pipe assembly (DPF catalytic converter)

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

Related Data List
DTC No. Data List
P244B
·

DPF Differential Pressure

·

Catalyst Differential Press

·

Exhaust Fuel Addition FB



MONITOR DESCRIPTION

The ECM compares the pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057E06
5.979,2.354 5.802,2.354 5.802,2.354 5.302,1.99 true 2.135,3.344 2.375,3.344 2.375,3.344 2.688,2.063 true 4,1.177 4.49,0.458 4.49,0.458 4.708,0.458 true 1.229,3.271 2.125,3.625 0.896,0.354 10 Stores P244B 3.531,2.906 4.688,3.198 1.156,0.292 10 Mass Air Flow 0.135,0.094 2.292,0.323 2.156,0.229 10 Differential Pressure Malfunction: 0.25,1.427 1.24,1.896 0.99,0.469 10 DPF Differential Pressure 4.771,0.375 5.969,0.604 1.198,0.229 10 Clogged with PM 5.76,1.031 7.146,1.458 1.385,0.427 10 Increases PM amount of DPF catalyst 6.042,2.271 6.969,2.646 0.927,0.375 10 No PM in DPF catalyst 1.125,0.729 1.51,0.958 0.385,0.229 10 High 5.604,2.896 5.99,3.125 0.385,0.229 10 High 1.125,2.563 1.51,2.792 0.385,0.229 10 Low 1.573,2.906 1.958,3.135 0.385,0.229 10 Low

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P244B Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 61

e.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Press value is more than 0.45, it indicates a high possibility that the DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P244B is output A
DTC P244B is output at the same time as P2463*
Other relevant DTCs are output B


HINT:

*: When P244B is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B is not output at the same time as P2463 is output, perform the diagnostic procedure for P244C.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P244C




A

3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

9.GO TO DTC CHART
3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
DPF Differential Pressure increases as engine speed increases from idle speed A
Except above B


A241154E04
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 Engine Speed (rpm) 0.833,2.99 1.74,3.375 0.906,0.385 10 MAF (gm/sec) 0.688,4.115 1.698,4.521 1.01,0.406 10 DPF Differential Pressure (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 A 1.771,1.875 1.875,2.156 0.104,0.281 10 0 1.781,3.24 1.885,3.521 0.104,0.281 10 0 1.792,4.615 1.896,4.896 0.104,0.281 10 0 0.677,0.854 1.948,1.24 1.271,0.385 10 Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

5.CHECK FOR BLACK SMOKE

B

4.CLEAN OR REPLACE AIR HOSE
4.CLEAN OR REPLACE AIR HOSE
a.

Even though it has been determined that the air hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B before repairing or cleaning it.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)

NG

8.REPLACE FRONT EXHAUST PIPE ASSEMBLY (DPF CATALYTIC CONVERTER)
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Catalyst Differential Press.

Powertrain > Engine > Data List
Tester Display
Catalyst Differential Press
50003 61 608

d.

Check the value of Catalyst Differential Press at 4000 rpm without load.

Result:
Result Proceed to
Catalyst Differential Press is more than 0.56 A
Except above B




A

8.REPLACE FRONT EXHAUST PIPE ASSEMBLY (DPF CATALYTIC CONVERTER)

B

7.PERFORM PM FORCED REGENERATION
7.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


e.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
8.REPLACE FRONT EXHAUST PIPE ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Even though it has been determined that the front exhaust pipe assembly (DPF catalytic converter) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.


Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B.


a.

Clean and/or repair the hoses of the differential pressure sensor assembly.


b.

Replace the front exhaust pipe assembly.


NOTICE:

Perform initialization procedure for "DPF Catalyst Record Clear".

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



Result:
Proceed to
NEXT



NEXT

END