Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0290063 CAMSHAFT(w/ DPF) A

1VD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


NOTICE:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


PROCEDURE

Hide 1.CHECK INJECTOR COMPENSATION CODE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 16400 7.REMOVE RADIATOR ASSEMBLY

Hide 44778 8.DISCONNECT CONNECTOR TO CHECK VALVE HOSE

Hide 87246A 9.DISCONNECT HEATER WATER HOSE

Hide 23271H 10.DISCONNECT NO. 1 AND NO. 2 FUEL HOSES

Hide 74403A 12.REMOVE BATTERY CARRIER SUB-ASSEMBLY

Hide 82111 13.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 17878 14.REMOVE NO. 3 INTAKE AIR CONNECTOR PIPE

Hide 29300 15.REMOVE VACUUM PUMP ASSEMBLY

Hide 44310 16.DISCONNECT VANE PUMP ASSEMBLY

Hide 87249B 17.DISCONNECT HEATER WATER OUTLET PIPE B

Hide 17940D 19.REMOVE INTERCOOLER ASSEMBLY

Hide 44769 23.REMOVE VACUUM RESERVOIR CONNECT TUBE

Hide 25850 24.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 82111 26.DISCONNECT ENGINE ROOM MAIN WIRE

a.
A391794

RH Side:

i.

Disconnect the 6 connectors.


ii.

Disconnect the 4 fuel injector connectors.


iii.

Remove the 5 bolts.


iv.

Detach the 2 clamps and disconnect the engine wire.



b.
A391795

LH Side:

i.

Disconnect the 6 connectors.


ii.

Disconnect the 4 fuel injector connectors.


iii.

Remove the 3 bolts.


iv.

Detach the 2 clamps and disconnect the engine wire.



c.
A391900

Remove the 2 bolts and disconnect the 2 ground wires.


d.

Detach the clamp from the No. 3 intercooler support bracket.


e.

Remove the 2 bolts and disconnect the 2 wire harness brackets.


f.
A391899

Detach the 2 clamps and disconnect the engine wire.


g.
A391898

Remove the 2 bolts and disconnect the 2 wire harness clamps and 2 connectors.


Hide 26100G 27.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 82112 29.DISCONNECT NO. 2 ENGINE ROOM WIRE

Hide 44761 30.REMOVE VACUUM PUMP TO CONNECTOR TUBE

Hide 15301 32.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 12142 33.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 11459 34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE SUPPORT

a.
A391906

Remove the 2 bolts and engine oil level dipstick guide support.


Hide 23706 35.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23764A 36.REMOVE NO. 4 NOZZLE LEAKAGE PIPE

Hide 23812D 38.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 23765 39.REMOVE NO. 5 NOZZLE LEAKAGE PIPE

Hide 23820A 40.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 41.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23810A 43.REMOVE COMMON RAIL ASSEMBLY RH

Hide 12263 44.DISCONNECT NO. 3 VENTILATION HOSE

Hide 23762B 45.REMOVE NO. 2 NOZZLE LEAKAGE PIPE

Hide 23670 47.REMOVE INJECTOR ASSEMBLY LH

Hide 12270 48.REMOVE OIL SEPARATOR ASSEMBLY

Hide 11202 49.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 12262 50.REMOVE NO. 2 VENTILATION HOSE

Hide 23761A 51.REMOVE NO. 1 NOZZLE LEAKAGE PIPE

Hide 23670 52.REMOVE INJECTOR ASSEMBLY RH

Hide 11201 53.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 13053 54.REMOVE NO. 3 AND NO. 4 CAMSHAFTS

a.
A168319C01
2.188,0.479 3.021,0.479 true 3.042,0.385 3.354,0.542 0.313,0.156 10 false *a
*a Arrow


Rotate the crankshaft clockwise, and align the No. 2 camshaft timing sprocket arrow with the cylinder head sub-assembly upper surface.


b.
A168320

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 2 chain tensioner assembly in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

U163084C01
0.844,1.552 0.844,2.354 true 2.677,0.271 2.802,0.417 0.125,0.146 10 false A 4.625,0.271 4.75,0.417 0.125,0.146 10 false B 6.25,0.271 6.375,0.417 0.125,0.146 10 false C 0.75,2.375 0.938,2.531 0.188,0.156 10 false *a
*a Stopper Plate - -



ii.

Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.




d.
A168364N01
2.031,0.667 2.833,0.667 true 2.875,0.583 3.333,0.781 0.458,0.198 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168322C01
1.667,1.333 1.667,1.167 1.667,1.167 2.406,0.906 true 1.594,1.323 1.906,1.479 0.313,0.156 10 false *a
*a Arrow


Rotate the crankshaft clockwise 360° so that the No. 2 camshaft timing sprocket arrow points at the No. 4 camshaft center.

NOTICE:

Do not rotate the crankshaft counterclockwise in order to align the No. 2 camshaft timing sprocket arrow and camshaft center.



g.
A168323C01
2.073,0.563 0.917,0.25 0.917,0.25 1.99,0.427 true 1.594,1.344 0.917,0.25 0.917,0.25 1.74,1.344 true 0.75,0.25 0.917,0.25 false 0.594,0.156 0.906,0.313 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket.


h.

Place matchmarks on the No. 3 and No. 4 camshaft gears.


i.
A168364N01
2.031,0.667 2.833,0.667 true 2.875,0.583 3.333,0.781 0.458,0.198 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts, No. 2 chain sub-assembly and No. 2 camshaft timing sprocket.

NOTICE:
·

Do not remove the No. 2 chain sub-assembly from the No. 2 camshaft timing sprocket.

·

Do not rotate the crankshaft until the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket are installed.



HINT:

If fixing the No. 2 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 2 camshaft timing sprocket holes and tie the No. 2 camshaft timing sprocket and No. 2 chain sub-assembly together.



k.
A168365

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the service bolt into the timing chain cover sub-assembly.


HINT:

If it is difficult to install the service bolt, rotate the camshaft so that the service bolt is easier to install.



l.
A168346

Loosen the 2 union bolts.


m.
A168347N01
2.01,1.208 2.198,1.396 0.188,0.188 10 true 20 1.656,1.781 1.969,1.979 0.313,0.198 10 false 19 1.99,0.865 2.198,1.031 0.208,0.167 10 true 18 1.635,0.302 1.833,0.469 0.198,0.167 10 true 17 2.573,1.198 2.76,1.375 0.188,0.177 10 true 16 2.24,1.792 2.552,1.99 0.313,0.198 10 false 15 2.583,0.854 2.781,1.052 0.198,0.198 10 true 14 2.229,0.302 2.438,0.458 0.208,0.156 10 true 13 1.417,1.208 1.625,1.375 0.208,0.167 10 true 12 1.063,1.792 1.375,1.99 0.313,0.198 10 false 11 1.406,0.875 1.604,1.052 0.198,0.177 10 true 10 1.083,0.281 1.219,0.448 0.135,0.167 10 true 9 3.177,1.208 3.313,1.396 0.135,0.188 10 true 8 3.188,1.427 3.323,1.594 0.135,0.167 10 true 7 3.198,0.865 3.333,1.031 0.135,0.167 10 true 6 3.208,0.625 3.344,0.802 0.135,0.177 10 true 5 0.323,1.292 0.438,1.479 0.115,0.188 10 true 4 0.385,1.74 0.5,1.927 0.115,0.188 10 true 3 0.281,0.802 0.396,0.99 0.115,0.188 10 true 2 0.292,0.323 0.438,0.51 0.146,0.188 10 true 1

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


n.
A168348

Remove the 2 union bolts and No. 3 and No. 4 camshaft oil feed pipe sub-assemblies.


o.
A168378

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



p.
A168350

Remove the No. 3 and No. 4 camshafts.


Hide 13511 55.REMOVE NO. 1 AND NO. 2 CAMSHAFTS

a.
A168309C01
0.417,0.396 1.438,0.396 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *a
*a Arrow


Rotate the crankshaft clockwise, and align the No. 1 camshaft timing sprocket arrow with the cylinder head sub-assembly upper surface.


b.
A168310

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 1 chain tensioner assembly in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

U163082C01
0.719,1.646 0.719,2.313 true 0.625,2.333 0.813,2.49 0.188,0.156 10 false *a 2.625,0.313 2.75,0.458 0.125,0.146 10 false A 4.469,0.313 4.594,0.458 0.125,0.146 10 false B 6.385,0.323 6.51,0.469 0.125,0.146 10 false C
*a Stopper Plate - -



ii.

Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.




d.
A168361N01
0.667,1.167 0.667,0.417 true 0.521,1.177 0.979,1.375 0.458,0.198 10 false SST

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168312C01
1.063,1 1.667,1.417 1.667,1.417 1.833,1.417 true 1.844,1.323 2.156,1.479 0.313,0.156 10 false *a
*a Arrow


Rotate the crankshaft clockwise 360° so that the No. 1 camshaft timing sprocket arrow points at the No. 1 camshaft center.

NOTICE:

Do not rotate the crankshaft counterclockwise in order to align the No. 1 camshaft timing sprocket arrow and camshaft center.



g.
A168313C01
1.469,0.573 2.5,0.25 2.5,0.25 1.552,0.469 true 1.854,1.292 2.5,0.25 2.5,0.25 1.719,1.302 true 2.5,0.25 2.667,0.25 false 2.677,0.156 2.99,0.313 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket.


h.

Place matchmarks on the No. 1 and No. 2 camshaft gears.


i.
A168362N01
0.667,1.083 0.667,0.375 true 0.531,1.094 0.99,1.292 0.458,0.198 10 false SST

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts and pump drive shaft gear.


k.

Disconnect the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket.

NOTICE:
·

Do not remove the No. 1 chain sub-assembly from the No. 1 camshaft timing sprocket.

·

Do not rotate the crankshaft until the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket are connected.



HINT:

If fixing the No. 1 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 1 camshaft timing sprocket holes and tie the No. 1 camshaft timing sprocket and No. 1 chain sub-assembly together.



l.
A168387

Turn the No. 1 camshaft clockwise so that the bolt is easier to install.


m.
A168363

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the service bolt into the timing chain cover sub-assembly.


HINT:

If it is difficult to install the service bolt, rotate the camshaft so that the service bolt is easier to install.



n.
A168341

Loosen the 2 union bolts.


o.
A168342N01
1.896,1.25 2.094,1.417 0.198,0.167 10 true 20 1.542,1.844 1.854,2.042 0.313,0.198 10 false 19 1.875,0.917 2.073,1.094 0.198,0.177 10 true 18 1.51,0.333 1.698,0.49 0.188,0.156 10 true 17 2.469,1.24 2.667,1.417 0.198,0.177 10 true 16 2.115,1.844 2.427,2.042 0.313,0.198 10 false 15 2.469,0.896 2.656,1.073 0.188,0.177 10 true 14 2.115,0.344 2.333,0.51 0.219,0.167 10 true 13 1.302,1.25 1.5,1.427 0.198,0.177 10 true 12 0.958,1.844 1.271,2.042 0.313,0.198 10 false 11 1.302,0.906 1.51,1.094 0.208,0.188 10 true 10 0.958,0.333 1.073,0.5 0.115,0.167 10 true 9 3.073,1.25 3.229,1.427 0.156,0.177 10 true 8 3.063,1.469 3.188,1.667 0.125,0.198 10 true 7 3.094,0.906 3.271,1.073 0.177,0.167 10 true 6 3.115,0.667 3.229,0.833 0.115,0.167 10 true 5 0.396,1.313 0.51,1.49 0.115,0.177 10 true 4 0.479,1.781 0.594,1.969 0.115,0.188 10 true 3 0.365,0.813 0.49,0.99 0.125,0.177 10 true 2 0.427,0.375 0.552,0.573 0.125,0.198 10 true 1

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


p.
A168343

Remove the 2 union bolts and No. 1 and No. 2 camshaft oil feed pipe sub-assemblies.


q.
A168344

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



r.

Remove the No. 1 and No. 2 camshafts.