Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  Engine Knocking or Rattling  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Knocking and abnormal sound due to extremely rich combustion

·

Abnormal sound due to friction between parts


(a) Fuel injector malfunctions
·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


(b) Abnormal common rail pressure
·

Suction control valve

·

Fuel pulsation sound

·

Air in fuel


(c) Friction between parts
(d) Compression pressure
·

Injector compensation codes

·

Fuel leakage

·

Intake system leakage

·

Intake system blockage

·

Throttle valve system

·

Fuel pressure sensor

·

Manifold absolute pressure sensor

·

Mass air flow meter

·

Atmospheric pressure sensor (built into ECM)

·

Vehicle modifications

·

Low quality fuel

·

Lack of fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



CAUTION / NOTICE / HINT

HINT:
·

This troubleshooting procedure checks for knocking and rattling.

·

Knocking is most likely to occur while the engine is idling.



NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION

·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION



PROCEDURE

1.CHECK SOUND AREA
a.

Find the source of the abnormal sound using a mechanic's sound scope.

Result:
Result Proceed to
Combustion noise from engine A
Noise from specific part B




A

2.READ OUTPUT DTCS (RELATING TO ENGINE)

B

REPAIR OR REPLACE MALFUNCTIONING PARTS

2.READ OUTPUT DTCS (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
No DTC is output A
Engine related DTCs are output B




A

3.CHECK INJECTOR COMPENSATION CODE

B

3.CHECK INJECTOR COMPENSATION CODE
NOTICE:

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


a.

Check the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 61 148
OK:

Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM.



Result:
Proceed to
OK
NG



OK

4.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)

NG

10.REGISTER INJECTOR COMPENSATION CODE
4.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Knocking.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

5.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)
5.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)
a.

Check Injection Feedback Val #1 to #8 and Injection Volume in the snapshot taken when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than +3 mm3/st A
Injection Volume is less than 5.5 mm3/st at 3000 rpm B
Except above C


HINT:
·

When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the fuel injectors are not malfunctioning.





A

6.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

B

13.REPLACE FUEL INJECTORS OF ALL CYLINDERS

C

14.CHECK SNAPSHOT (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
6.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.


d.

Check the engine speed during the Active Test.

Powertrain > Engine and ECT > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine Speed of Cyl #5
Engine Speed of Cyl #6
Engine Speed of Cyl #7
Engine Speed of Cyl #8
50004 61 111 492,493,494,495,496,497,498,499
Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #8 are within +/-10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

7.CHECK CYLINDER COMPRESSION PRESSURE

B

8.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

When compression is low, there may be cracks in the piston or the injector may be installed improperly.



Result:
Proceed to
OK
NG



OK

8.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
a.

Replace the fuel injector of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

10.REGISTER INJECTOR COMPENSATION CODE
10.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 61 148

Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the knocking has been successfully repaired.


Result:
Proceed to
NEXT



NEXT

END

13.REPLACE FUEL INJECTORS OF ALL CYLINDERS
a.

Replace the fuel injectors all cylinders.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

9.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
14.CHECK SNAPSHOT (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was warmed up and idling.

OK:

Fuel Press is within 5000 kPa of Target Common Rail Pressure.



Result:
Proceed to
OK
NG



OK

15.CHECK ENGINE KNOCKING OR RATTLING

NG

20.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
15.CHECK ENGINE KNOCKING OR RATTLING
a.

Check engine knocking or rattling.

Result:
Result Proceed to
Sound disappears A
Except above (Sound continues occurring) B




A

END

B

16.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS
16.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS
a.

Check the temperature when knocking trouble occurs.

Result:
Result Proceed to
Knocking occurs only in cold engine A
Knocking occurs both in cold and warmed up engine B




A

17.INSPECT GLOW PLUG (RESISTANCE)

B

24.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
17.INSPECT GLOW PLUG (RESISTANCE)

Result:
Proceed to
OK
NG



OK

18.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD)

NG

18.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD)
a.

Make sure that the engine is cold so that the snapshot can be taken under the correct conditions.


b.

Connect the GTS to the DLC3.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Knocking.


e.

Take a snapshot of the following Data List items.

HINT:

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.



Result:
Proceed to
NEXT



NEXT

19.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #8)
19.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #8)
a.

Check Injection Feedback Val #1 to #8 in the snapshot taken when the engine was idling.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than +3 mm3/st A
Except above B


HINT:
·

When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the fuel injector are not malfunctioning.





A

8.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

B

24.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
20.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/o DPF)>REMOVAL

HINT:

If the Fuel Press becomes too high when transitioning due to problems with pre-stroke control valve operation, knocking noise worsens.

When the Fuel Press becomes excessively high as a result of a suction control valve malfunction, knocking sounds worsen.



Result:
Proceed to
NEXT



NEXT

21.BLEED AIR FROM FUEL SYSTEM
21.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

22.PERFORM FUEL SUPPLY PUMP INITIALIZATION
22.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

23.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the knocking has been successfully repaired by starting the engine.


Result:
Proceed to
NEXT



NEXT

END

24.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
MAP
50003 61 64,314

d.

Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).

Standard:

Difference between MAP and Atmosphere Pressure is less than 8 kPa.


HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

The standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, the pressure drops by 1 kPa. This varies by weather.



Result:
Result Proceed to
MAP and Atmosphere Pressure have same value A
MAP is different from actual atmospheric pressure B
Atmosphere Pressure is different from actual atmospheric pressure C




A

25.BASIC INSPECTION

B

C

25.BASIC INSPECTION
a.

Check the fuel quality.


b.

Check the fuel for air.


c.

Check the fuel system for blockages.


d.

Check the air cleaner filter element sub-assembly.


e.

Check the engine oil.


f.

Check the engine coolant.


g.

Check the engine idling speed and maximum engine speed.


h.

Check the vacuum pump.


Result:
Proceed to
NEXT



NEXT

END