w/ VSC
The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.
*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
w/o VSC
The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.
*1: w/ Speedometer Sensor
*2: w/o Speedometer Sensor
w/o VSC:
If the speedometer operation is not normal, refer to "Speedometer Malfunction".
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction
For vehicles without a tire pressure warning system, proceed to the next step.
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*5
Disconnect the U5*8, S33*9 or Y10*10 tire pressure warning ECU and receiver connector.*7
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles with a 1HZ, proceed to the next step.
*1: for 1HZ (w/ EGR System)
*2: for LHD
*3: for RHD
*4: w/ Differential Lock
*5: w/ Tire Pressure Warning System
*6: except Single and Double Cabs
*7: for Single Cab
*8: for Double Cab
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I128*2 or A31*3 emission control ECU connector.*1
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*4
Disconnect the U5*6, S33*7 or Y10*8 tire pressure warning ECU and receiver connector.*5
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a 1HZ (w/ EGR system), proceed to the next step.
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: w/ Differential Lock
*4: w/ Tire Pressure Warning System
*5: except Single and Double Cabs
*6: for Single Cab
*7: for Double Cab
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*3
Disconnect the U5*5, S33*6 or Y10*7 tire pressure warning ECU and receiver connector.*4
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a differential lock, proceed to the next step.
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the U5*7, S33*8 or Y10*9 tire pressure warning ECU and receiver connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ ABS | A |
| w/ VSC, w/o Pre-Collision System | B |
| w/ Pre-Collision System | C |
| w/o ABS | D |
A
B
C
D
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A20-22 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Waveform |
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal L25-9 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | L25-9 (SI) - Body ground |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ ABS:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/o VSC)>REMOVAL
w/ VSC:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ VSC)>REMOVAL
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
Disconnect the L25 combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*6
Disconnect the U5*8, S33*9 or Y10*10 tire pressure warning ECU and receiver connector.*7
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - U5-2 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or U5-2 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - S33-2 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or S33-2 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - Y10-2 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or Y10-2 (SPD) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (except Single and Double Cabs) | A |
| OK (for Single Cab) | B |
| OK (for Double Cab) | C |
| NG | D |
A
for Short Body:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Short Body)>REMOVAL
for Long Body:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Long Body)>REMOVAL
for Semi-long Body:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Semi-long Body)>REMOVAL
B
C
D
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
Disconnect the L25 combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*6
Disconnect the U5*8, S33*9 or Y10*10 tire pressure warning ECU and receiver connector.*7
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - L9-5 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or L9-5 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
Disconnect the L25 combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*6
Disconnect the U5*8, S33*9 or Y10*10 tire pressure warning ECU and receiver connector.*7
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - I84-8 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or I84-8 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - A29-8 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or A29-8 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1VD-FTV:
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: w/ Differential Lock
*4: for LHD
*5: for RHD
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
Disconnect the L25 combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*3
Disconnect the I128*4 or A31*5 emission control ECU connector.
Disconnect the U5*7, S33*8 or Y10*9 tire pressure warning ECU and receiver connector.*6
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - A31-5 (SP1) | Always | Below 1 Ω |
| L25-8 (+S) or A31-5 (SP1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - I128-5 (SP1) | Always | Below 1 Ω |
| L25-8 (+S) or I128-5 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE (for LHD), for 1VD-FTV (for LHD)
*2: for 1GR-FE (for RHD), for 1VD-FTV (for RHD)
*3: for 1HZ (w/ EGR System)
*4: for LHD
*5: for RHD
*6: w/ Differential Lock
*7: w/ Tire Pressure Warning System
*8: except Single and Double Cabs
*9: for Single Cab
*10: for Double Cab
Disconnect the L25 combination meter assembly connector.
Disconnect the L9 clock assembly connector.
Disconnect the I84*1 or A29*2 ECM connector.
Disconnect the I128*4 or A31*5 emission control ECU connector.*3
Disconnect the I8 No. 2 4 wheel drive control ECU connector.*6
Disconnect the U5*8, S33*9 or Y10*10 tire pressure warning ECU and receiver connector.*7
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-8 (+S) - I8-4 (SPD) | Always | Below 1 Ω |
| L25-8 (+S) or I8-4 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L25 combination meter assembly connector.
Disconnect the A20 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-9 (SI) - A20-22 (SP1) | Always | Below 1 Ω |
| L25-9 (SI) or A20-22 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A42-14 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L25 combination meter assembly connector.
Disconnect the A42 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-9 (SI) - A42-14 (SP1) | Always | Below 1 Ω |
| L25-9 (SI) or A42-14 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A45-18 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L25 combination meter assembly connector.
Disconnect the A45 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-9 (SI) - A45-18 (SP1) | Always | Below 1 Ω |
| L25-9 (SI) or A45-18 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG