Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the ignition switch ON and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch while holding a seat memory switch LH (for LHD) or RH (for RHD) (M1 or M2 switch) will register the transmitter recognition code into the seat memory switch LH (for LHD) or RH (for RHD) that was pressed. After registration is completed, the answer back buzzer sounds.

CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.



HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the power door lock control system.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

The power door lock control system operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK ENTRY AND START SYSTEM (Start Function)

NG

2.CHECK ENTRY AND START SYSTEM (Start Function)
a.

Check the entry and start system (for start function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

OK:

The entry and start system (for start function) operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION

NG

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
OK A
NG (Seat position memory function does not operate normally) B
NG (Seat position restoring function does not operate normally) C



A

4.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

4.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF ON: Front right door open
OFF: Front right door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF ON: Front left door open
OFF: Front left door closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID16
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*

*1: Although this item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

A seat position memory switch is linked to the electrical key transmitter sub-assembly.



Result:
Proceed to
OK
NG



OK

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered and the automatic memory call function operates normally.



Result:
Proceed to
OK
NG



OK

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate)

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

B

10.REPLACE POSITION CONTROL ECU ASSEMBLY LH

C

12.REPLACE POSITION CONTROL ECU ASSEMBLY RH
10.REPLACE POSITION CONTROL ECU ASSEMBLY LH
a.

Replace the position control ECU assembly LH with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.REPLACE POSITION CONTROL ECU ASSEMBLY RH
a.

Replace the position control ECU assembly RH with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
13.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)