Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P1AFD00  Flying Capacitor Circuit Voltage Out of Range  


DESCRIPTION

The battery ECU assembly monitors its internal operation and will store a DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1AFD00 Flying Capacitor Circuit Voltage Out of Range ECU internal malfunction
(1 trip detection logic)
·

Battery ECU assembly

·

Battery voltage sensor (for upper side)

·

Battery voltage sensor (for lower side)

·

Wire harness or connector

·

EV battery terminal block

·

No. 1 EV supply stack sub-assembly

·

No. 2 EV supply stack sub-assembly


Master Warning:
Comes on
EV Battery A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 30 seconds or more.

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0E2D00.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly is disposed of improperly or abandoned. Therefore, make sure to return all EV supply battery assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly to produce heat, resulting in a fire.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
Only P1AFD00 is output A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK ODOMETER

B

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

2.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

3.CHECK EV BATTERY TERMINAL BLOCK (EV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
3.CHECK EV BATTERY TERMINAL BLOCK (EV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
C371877

Check the connections of the EV battery high voltage connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Result Proceed to
OK A
Either connector was not connected securely The terminals are not damaged or corroded B
Either connector was not connected securely The terminal is damaged or corroded
(The No. 1 EV supply stack sub-assembly side connector)
C
Either connector was not connected securely The terminal is damaged or corroded
(The No. 2 EV supply stack sub-assembly side connector)
D


Post-procedure1

a.

Install the upper EV battery cover panel.



A

4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

B

CONNECT SECURELY

C

10.CHECK TOTAL DISTANCE DRIVEN

D

16.CHECK TOTAL DISTANCE DRIVEN
4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z14 or z15 was not connected securely The terminals are damaged or corroded C



A

5.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)

B

CONNECT SECURELY

C

11.CHECK TOTAL DISTANCE DRIVEN
5.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z16 or z17 was not connected securely The terminals are damaged or corroded C



A

6.CHECK EV BATTERY TERMINAL BLOCK

B

CONNECT SECURELY

C

12.CHECK TOTAL DISTANCE DRIVEN
6.CHECK EV BATTERY TERMINAL BLOCK

OK

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)

NG

REPLACE EV BATTERY TERMINAL BLOCK

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



c.

Disconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
C373310N06
0.385,0.458 0.802,0.75 0.417,0.292 0.49,0.531 0.74,0.708 0.25,0.177 10 true y2

Disconnect the y2 battery ECU assembly connector.


NOTICE:
·

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

·

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



f.

Disconnect the y3 battery voltage sensor (for lower side) connector.

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C374919C36
1.51,2.438 1.948,2.698 0.438,0.26 1.49,0.208 1.927,0.469 0.438,0.26 1.927,2 1.531,1.438 true 0.938,4.229 1.208,3.458 true 2.844,4.24 3.063,3.458 true 0.792,1.135 0.469,0.583 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.677,2.51 1.99,2.708 0.313,0.198 10 false y1 2.688,4.292 3.146,4.49 0.458,0.198 10 false GA0 0.302,0.396 0.76,0.594 0.458,0.198 10 false GA0 0.76,4.302 1.375,4.5 0.615,0.198 10 false VBB1 1.823,2.083 2.438,2.281 0.615,0.198 10 false VBB1 0.052,0.198 0.365,0.354 0.313,0.156 10 false *a 0.115,2.448 0.427,2.604 0.313,0.156 10 false *b
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y1)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

y2-17 (GA0) - y1-19 (GA0) Always Below 1 Ω
y2-32 (VBB1) - y1-34 (VBB1) Always Below 1 Ω



b.
C374919C37
1.5,2.396 1.948,2.646 0.448,0.25 1.5,0.208 1.948,0.458 0.448,0.25 2.167,2.063 2.365,1.469 true 0.844,4.219 1.208,3.438 true 2.729,4.24 3.073,3.469 true 1.521,1.146 1.167,0.49 true 1.656,0.271 1.969,0.469 0.313,0.198 10 false y2 1.656,2.458 1.969,2.656 0.313,0.198 10 false y3 0.125,0.167 0.438,0.323 0.313,0.156 10 false *a 0.146,2.385 0.458,2.542 0.313,0.156 10 false *b 2.563,4.333 3.021,4.531 0.458,0.198 10 false GA2 0.969,0.313 1.427,0.51 0.458,0.198 10 false GA2 1.99,2.135 2.448,2.333 0.458,0.198 10 false VBB3 0.646,4.302 1.104,4.5 0.458,0.198 10 false VBB3
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y3)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

y2-12 (GA2) - y3-19 (GA2) Always Below 1 Ω
y2-26 (VBB3) - y3-34 (VBB3) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).



b.

Reconnect the y2 battery ECU assembly connector.


c.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




OK

8.CHECK BATTERY VOLTAGE SENSOR (for Upper Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BATTERY VOLTAGE SENSOR (for Upper Side)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of battery voltage sensor.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C374921C22
1.51,1.104 1.896,1.354 0.385,0.25 0.594,3.521 0.979,3.771 0.385,0.25 2.396,3.51 2.781,3.76 0.385,0.25 2.958,2.156 2.75,1.729 true 1.042,2.177 1.344,1.74 true 2.958,4.385 3.292,4.073 true 0.5,4.396 0.115,4.073 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.656,1.167 1.969,1.365 0.313,0.198 10 false y1 0.688,3.583 1.146,3.781 0.458,0.198 10 false z14 2.479,3.583 2.938,3.781 0.458,0.198 10 false z15 2.854,2.229 3.313,2.427 0.458,0.198 10 false GA0 0.604,4.396 1.063,4.594 0.458,0.198 10 false GA0 2.573,4.365 3.031,4.563 0.458,0.198 10 false VA42 0.823,2.229 1.281,2.427 0.458,0.198 10 false VBB1
*a Component without harness connected
(to Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y1,z14,z15)Location & Routing

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

Click Connector(z14)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

Click Connector(z15)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

y1-19 (GA0) - z14-10 (GA0) Always 5.88 to 6.12 kΩ
y1-34 (VBB1) - z15-1 (VA42) Always 5.88 to 6.12 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




OK

9.CHECK BATTERY VOLTAGE SENSOR (for Lower Side)

NG

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

9.CHECK BATTERY VOLTAGE SENSOR (for Lower Side)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of battery voltage sensor.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).



Procedure1

a.
C374921C23
1.51,1.104 1.896,1.354 0.385,0.25 0.594,3.521 0.979,3.771 0.385,0.25 2.396,3.51 2.781,3.76 0.385,0.25 2.958,2.156 2.75,1.729 true 1.042,2.177 1.344,1.74 true 2.958,4.385 3.323,4.083 true 0.5,4.396 0.125,4.073 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.656,1.167 1.969,1.365 0.313,0.198 10 false y3 0.688,3.583 1.146,3.781 0.458,0.198 10 false z16 2.479,3.583 2.938,3.781 0.458,0.198 10 false z17 2.854,2.229 3.313,2.427 0.458,0.198 10 false GA2 0.604,4.396 1.063,4.594 0.458,0.198 10 false GA2 2.573,4.365 3.031,4.563 0.458,0.198 10 false VA84 0.823,2.229 1.281,2.427 0.458,0.198 10 false VBB3
*a Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y3,z16,z17)Location & Routing

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

Click Connector(z16)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

Click Connector(z17)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

y3-19 (GA2) - z16-10 (GA2) Always 5.88 to 6.12 kΩ
y3-34 (VBB3) - z17-1 (VA84) Always 5.88 to 6.12 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).




OK

NG

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

10.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

13.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
11.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

14.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
12.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

15.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
13.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

14.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

15.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

16.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

17.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
17.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK