Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314A31  Motor Electronics Coolant Pump "A" No Signal  


DESCRIPTION

Refer to the description for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

The water with motor pump assembly sends the water pump speed (measured value) signal to the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P314A31 Motor Electronics Coolant Pump "A" No Signal The water pump speed signal is not sent to the EV control ECU when the ignition switch is turned to ON (READY).*
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

Water with motor pump assembly

·

INV W/PMP fuse

·

INV W/PMP relay


Master Warning:
Comes on
EV A

*: Either of the following conditions is met.
·

A malfunction (open, short to +B or short to ground) in the speed signal line from the water with motor pump assembly to the EV control ECU is detected.

·

A malfunction in the water with motor pump assembly power source circuit is detected.

·

A malfunction in the +B line is detected.

·

A malfunction in EV control ECU power source circuit is detected.


Related Data List
DTC No. Data List
P314A31
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Ready Signal



Related Active Test
DTC No. Active Test
P314A31 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the EV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.



HINT:
·

When the auxiliary battery voltage is low, the water with motor pump assembly may not operate.

·

When the water with motor pump assembly signal line (SWP - IWP) is open or its connection is faulty, the water with motor pump assembly is operated forcibly.



Pre-procedure1

a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > EV > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump
50004 397 1 30

Procedure1

a.

Touch the water with motor pump assembly and check that it is operating (vibrating).

OK:

The water with motor pump is operating (vibrating).


HINT:

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV control ECU connector.


b.

Disconnect the B27 water with motor pump assembly connector.


Procedure1

a.
A479463C03
1.51,2.958 1.948,3.281 0.438,0.323 2.073,0.135 2.49,0.458 0.417,0.323 1.677,4.24 1.615,3.802 true 2.74,2.313 2.344,1.885 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 0.188,2.906 0.5,3.063 0.313,0.156 10 false *b 1.635,3.052 1.948,3.25 0.313,0.198 10 false B27 1.542,4.25 2,4.448 0.458,0.198 10 false NWP 2.167,0.24 2.479,0.438 0.313,0.198 10 false A17 2.656,2.333 3.115,2.531 0.458,0.198 10 false NIWP
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to Water with Motor Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,B27)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B27)Engine Compartment>No. 2 Stack Wire>Water Pump with Motor Assembly

A17-10 (NIWP) - B27-2 (NWP) Ignition switch off Below 1 Ω
A17-10 (NIWP) or B27-2 (NWP) -Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B27 water with motor pump assembly connector.


b.

Reconnect the A17 EV control ECU connector.



OK

6.CHECK EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK EV CONTROL ECU

Pre-procedure1

a.

Disconnect the B27 water with motor pump assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.
A478491C19
1.969,0.875 2.406,1.188 0.438,0.313 2.219,1.688 1.99,2.51 true 2.292,1.75 2.635,2.542 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.906,2.552 2.354,2.719 0.448,0.167 10 false E1 2.542,2.552 2.99,2.719 0.448,0.167 10 false NIWP 2.083,0.969 2.385,1.135 0.302,0.167 10 false A17
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-10 (NIWP) - A17-4 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the B27 water with motor pump assembly connector.



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the water with motor pump assembly may not operate.


Pre-procedure1

a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > EV > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump
50004 397 1 30

Procedure1

a.
A481524C02
2.052,0.135 2.5,0.479 0.448,0.344 1.948,1.656 2.281,0.958 true 2.75,1.656 2.354,1.031 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.875,3.625 3.333,3.823 0.458,0.198 10 false GND 2.688,1.667 3.302,1.865 0.615,0.198 10 false NIWP 2.156,0.229 2.615,0.427 0.458,0.198 10 false A17 1.823,1.656 2.281,1.854 0.458,0.198 10 false E1
*a Component with harness connected
(to EV Control ECU)


Connect an oscilloscope between the EV control ECU terminals specified in the table below, and measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-10 (NIWP) - A17-4 (E1) Ignition switch ON, during Active Test 5 V/DIV., 5 ms./DIV.

OK:

The duration of wavelength is 13 msec or less.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

17.REPLACE WATER WITH MOTOR PUMP ASSEMBLY
9.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)

NG

CONNECT SECURELY (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)
a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Check installation condition of the INV W/PMP relay.

OK:

INV W/PMP relay is installed correctly.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGCT NO.2 RELAY - INV W/PMP RELAY)

NG

19.INSPECT RELAY (INV W/PMP)
11.CHECK HARNESS AND CONNECTOR (IGCT NO.2 RELAY - INV W/PMP RELAY)

Pre-procedure1

a.
A480806C03
0.167,0.167 0.479,0.323 0.313,0.156 10 false *1 1.292,0.427 1.604,0.583 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 2 Relay


Remove the IGCT NO. 2 relay from the luggage room relay block.


b.
A479465C02
0.083,0.083 0.396,0.24 0.313,0.156 10 false *1 2.688,0.479 3,0.635 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 front compartment relay block


Procedure1

a.
A288054C11
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT NO. 2 relay holder) - 1 (INV W/PMP relay holder) Ignition switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


HINT:
·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

Luggage Room Relay Block

Apply slight vibration with a finger to the luggage room relay block and check whether a malfunction occurs.

·

No. 1 Front Compartment Relay Block

Apply slight vibration with a finger to the No. 1 front compartment relay block and check whether a malfunction occurs.

·

IGCT NO. 5 fuse

Apply slight vibration with a finger to the IGCT NO. 5 fuse and check whether a malfunction occurs.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 2 relay and INV W/PMP relay.



OK

12.INSPECT RELAY (INV W/PMP)

NG

20.CHECK INSTALLATION CONDITION (IGCT NO. 5 FUSE)
12.INSPECT RELAY (INV W/PMP)

Pre-procedure1

a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 front compartment relay block.


Procedure1

a.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP relay.



OK

13.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY - BODY GROUND)

NG

22.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
13.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY - BODY GROUND)

Pre-procedure1

A481459C01
1.458,1.021 1.938,1.385 0.479,0.365 2.354,2.51 2.021,1.927 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.198,2.563 2.656,2.76 0.458,0.198 10 false +BWP 1.594,1.135 2.01,1.313 0.417,0.177 10 false B27
*a Front view of wire harness connector
(to Water with Motor Pump Assembly)


A288054C11
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


a.

Disconnect the B27 water with motor pump assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B27)Location & Routing

Click Connector(B27)Engine Compartment>No. 2 Stack Wire>Water Pump with Motor Assembly

B27-4 (+BWP) - Body ground Ignition switch ON 11 to 14 V


NOTICE:
·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

·

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



HINT:
·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 1 Front Compartment Relay Block

Apply slight vibration with a finger to the No. 1 front compartment relay block and check whether a malfunction occurs.

·

INV W/PMP fuse

Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.

·

INV W/PMP Relay

Apply slight vibration with a finger to the INV W/PMP relay and check whether a malfunction occurs.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B27 water with motor pump assembly connector.



OK

14.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY - BODY GROUND)

NG

23.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
14.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the B27 water with motor pump assembly connector.


Procedure1

a.
A481459C02
1.49,1.063 1.906,1.302 0.417,0.24 1.208,2.469 1.396,1.917 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.052,2.521 1.51,2.719 0.458,0.198 10 false GND 1.594,1.104 2.01,1.281 0.417,0.177 10 false B27
*a Front view of wire harness connector
(to Water with Motor Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B27)Location & Routing

Click Connector(B27)Engine Compartment>No. 2 Stack Wire>Water Pump with Motor Assembly

B27-1 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B27 water with motor pump assembly connector.



OK

15.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

16.ADD EV COOLANT AND PERFORM AIR BLEEDING
16.ADD EV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the water with motor pump assembly, add EV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

END

17.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

18.ADD EV COOLANT AND PERFORM AIR BLEEDING
18.ADD EV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the water with motor pump assembly, add EV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

END

19.INSPECT RELAY (INV W/PMP)

Pre-procedure1

a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 front compartment relay block.


Procedure1

a.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP relay.



OK

CONNECT SECURELY (INV W/PMP RELAY)

NG

REPLACE RELAY (INV W/PMP)

20.CHECK INSTALLATION CONDITION (IGCT NO. 5 FUSE)
a.
A481457C01
2.865,1.656 2.656,0.542 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *1 2.552,0.375 2.865,0.531 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 5 Fuse


Check installation condition of the IGCT NO. 5 fuse.

OK:

IGCT NO. 5 fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

21.CHECK FUSE (IGCT NO. 5)

NG

27.INSPECT RELAY (INV W/PMP)
21.CHECK FUSE (IGCT NO. 5)

Pre-procedure1

a.
A481457C01
2.865,1.656 2.656,0.542 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *1 2.552,0.375 2.865,0.531 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 5 Fuse


Remove the IGCT NO. 5 fuse from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 5 fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 5 fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 5 FUSE HOLDER TERMINAL)

NG

28.CHECK FUSE HOLDER TERMINAL (IGCT NO. 5)
22.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE RELAY (INV W/PMP)

NG

29.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
23.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
a.
A479464C01
2.01,2.063 2.604,2.625 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 2.656,2.583 2.969,2.74 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Fuse


Check installation condition of the INV W/PMP fuse.

OK:

INV W/PMP fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

24.INSPECT RELAY (INV W/PMP)

NG

CONNECT SECURELY (INV W/PMP FUSE)

24.INSPECT RELAY (INV W/PMP)

Pre-procedure1

a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 front compartment relay block.


Procedure1

a.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP relay.



OK

25.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY CIRCUIT)

NG

30.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
25.CHECK HARNESS AND CONNECTOR (WATER WITH MOTOR PUMP ASSEMBLY CIRCUIT)

Pre-procedure1

a.

Remove the INV W/PMP fuse from the No. 1 front compartment relay block.


b.

Remove the INV W/PMP relay from the No. 1 front compartment relay block.


c.

Disconnect the B27 water with motor pump assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481458C01
1.625,0.74 2.021,1.042 0.396,0.302 2.083,1.479 2.542,1.865 true 3.833,0.083 4.146,0.24 0.313,0.156 10 false *1 6.552,1.802 6.865,1.958 0.313,0.156 10 false *2 6.167,0.313 6.479,0.469 0.313,0.156 10 false *3 0.938,0.677 1.25,0.833 0.313,0.156 10 false *a 1.719,0.833 2.031,1.031 0.313,0.198 10 false B27 2.573,1.875 3.188,2.073 0.615,0.198 10 false +BWP
*1 No. 1 Front Compartment Relay Block *2 INV W/PMP Fuse
*3 INV W/PMP Relay - -
*a Front view of wire harness connector
(to Water with Motor Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B27)Location & Routing

Click Connector(B27)Engine Compartment>No. 2 Stack Wire>Water Pump with Motor Assembly

B27-4 (+BWP) - 3 (INV W/PMP relay holder) Ignition switch off Below 1 Ω
2 (INV W/PMP relay holder) - 3 (INV W/PMP relay holder) Ignition switch off Below 1 Ω
3 (INV W/PMP fuse holder) or B27-4 (+BWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B27 water with motor pump assembly connector.


b.

Install the INV W/PMP relay.


c.

Install the INV W/PMP fuse.



OK

26.CHECK FUSE (INV W/PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK FUSE (INV W/PMP)
A479464C01
2.01,2.063 2.604,2.625 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 2.656,2.583 2.969,2.74 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Fuse


Pre-procedure1

a.

Remove the INV W/PMP fuse from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL OR INV W/PMP RELAY HOLDER TERMINAL)

NG

32.REPLACE WATER WITH MOTOR PUMP ASSEMBLY
27.INSPECT RELAY (INV W/PMP)

Pre-procedure1

a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 front compartment relay block.


Procedure1

a.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP relay.



OK

CONNECT SECURELY (IGCT NO. 5 FUSE)

NG

34.REPLACE RELAY (INV W/PMP)
28.CHECK FUSE HOLDER TERMINAL (IGCT NO. 5)
a.
A481457C01
2.865,1.656 2.656,0.542 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *1 2.552,0.375 2.865,0.531 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 5 Fuse


Check the terminals of the IGCT NO. 5 fuse holder.

OK:

The terminals of the IGCT NO. 5 fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 5)

NG

35.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 5 FUSE HOLDER TERMINAL)
29.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

30.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.
A481456C01
1.875,1.24 2.542,0.865 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 2.583,0.771 2.896,0.927 0.313,0.156 10 false *2
*1 No. 1 Front Compartment Relay Block
*2 INV W/PMP Relay


Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

31.CHECK FUSE (IGCT NO. 5)

NG

36.CHECK FUSE (IGCT NO. 5)
31.CHECK FUSE (IGCT NO. 5)
A481457C01
2.865,1.656 2.656,0.542 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *1 2.552,0.375 2.865,0.531 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 5 Fuse


Pre-procedure1

a.

Remove the IGCT NO. 5 fuse from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 5 fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 5 fuse.



OK

REPLACE RELAY (INV W/PMP)

NG

38.REPLACE RELAY (INV W/PMP)
32.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

33.ADD EV COOLANT AND PERFORM AIR BLEEDING
33.ADD EV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the water with motor pump assembly, add EV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

34.REPLACE RELAY (INV W/PMP)
a.

Replace INV W/PMP relay.


Result:
Proceed to
NEXT



NEXT

CONNECT SECURELY (IGCT NO. 5 FUSE)

35.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 5 FUSE HOLDER TERMINAL)
a.

Repair or replace the terminals of the IGCT NO. 5 fuse holder.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 5)

36.CHECK FUSE (IGCT NO. 5)
A481457C01
2.865,1.656 2.656,0.542 true 0.26,0.292 0.573,0.448 0.313,0.156 10 false *1 2.552,0.375 2.865,0.531 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 5 Fuse


Pre-procedure1

a.

Remove the IGCT NO. 5 fuse from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 5 fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 5 fuse.



OK

37.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)

NG

39.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
37.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

38.REPLACE RELAY (INV W/PMP)
a.

Replace INV W/PMP relay.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 5)

39.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

40.REPLACE RELAY (INV W/PMP)
40.REPLACE RELAY (INV W/PMP)
a.

Replace INV W/PMP relay.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 5)